• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.05a
• /
• pp.288-292
• /
• 2002

We propose the new type of on-chip ESD protection method for RF applications. By using the properties of RF circuits, we can use the short-circuited stub as ESD protection device in front of the DC blocking capacitor Specially, we can use short-circuited stub as the portion of the matching circuit so to reduce the and various parameters of the transmission line. This new type ESD protection method is very different from the conventional ESD protection method. With the new type ESD protection method, we remove the parasitic capacitance of ESD protection device which degrade the performance of core circuit.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.4 no.1
• /
• pp.29-34
• /
• 2009

In this paper, we design RF transceiver architecture and building blocks for impulse radio UWB system. Impulse radio UWB signal occupies the wide frequency band which is very low transmission power. So, it can minimize the interference effect with the other system. Using UWB technology, we obtain position awareness service. Therefore, we describe the RF transceiver architecture of direct conversion receiver and define the requirement of RF transceiver. Moreover, we implement a prototype RF transceiver based on the presented standard and verify a function and performance through the wireless data communication and ranging test.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2003.11a
• /
• pp.175-179
• /
• 2003

In this paper, we developed a DTV RF (Radio frequency) capture, analysis, and regeneration system adapting digital signal processing and high speed hard disk interfacing techniques and analyzed characteristics of captured RF signal. This system can be used in the various field of DTV transmission because this system can capture the receiving real DTV signals and analyze captured RF signals that contain the complex characteristics of the real-world RF environments and regenerate it in a laboratory without the performance degradation. The system can capture and replay the DTV RF signals in real-time on hard disk. Therefore, there is no limit for the amount of captured data with in the installed storage capacity. We can expect various possible applications for this system such as a tool for the development of the receiver performance analysis, design, and analysis for the DTV coverage areas, etc. This system can also be used as RF signal analyzer.

• Journal of electromagnetic engineering and science
• /
• v.16 no.1
• /
• pp.24-28
• /
• 2016

This study presents a conductivity measurement technique that is applicable at radio frequencies (RF). Of particular interest is the measurement of the RF conductivity of a flexible Zell fabric, which is often used to implement wearable antennas on clothes. First, the transmission coefficient is measured using a planar microstrip ring resonator, where the ring is made of a Zell fabric. Then, the fabric's conductivity is determined by comparing the measured transmission coefficient to a set of simulation data. Specifically, a MATLAB-based root-searching algorithm is used to find the minimum of an error function composed of measured and simulation data. Several error functions have been tested, and the results showed that an error function employing only the magnitude of the transmission coefficient was the best for determining the conductivity. The effectiveness of this technique is verified by the measurement of a known copper foil before characterizing the Zell fabric. The conductivity of the Zell fabric at 2 GHz appears to be within the order of $10^4S/m$, which is lower than the DC conductivity of $5{\times}10^5S/m$.

• Journal of Communications and Networks
• /
• v.18 no.3
• /
• pp.340-350
• /
• 2016

The performance of large-scale cognitive radio (CR) networks with secondary users sustained by opportunistically harvesting radio-frequency (RF) energy from nearby primary transmissions is investigated. Using an advanced RF energy harvester, a secondary user is assumed to be able to collect ambient primary RF energy as long as it lies inside the harvesting zone of an active primary transmitter (PT). A variable power (VP) transmission mode is proposed, and an energy-based opportunistic spectrum access (OSA) strategy is considered, under which a secondary transmitter (ST) is allowed to transmit only if its harvested energy is larger than a predefined transmission threshold and it is outside the guard zones of all active PTs. The transmission probability of the STs is derived. The outage probabilities and the throughputs of the primary and the secondary networks, respectively, are characterized. Compared with prior work, the throughput can be increased by as much as 29%. The energy-based OSA strategy can be generally applied to a non-CR setup, where distributed power beacons (PBs) are deployed to power coexisting wireless signal transmitters (WSTs) in a wireless powered sensor network.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.7 no.8
• /
• pp.1612-1620
• /
• 2003

This papers describes a nonlinear transfer function modelling of designed GaAs FET power amplifier by measured and simulated values of designed PA amplifier for multi­carrier transmission system, With the results of PA nonlinearity characteristic, we can estimates AM­AM and AM­PM of designed PA. According to the estimated nonlinear characteristics, we can analysis the ACPR of PA for spectral regrowth, the error vector measurement(EVM) of constallation signals and bit error rate of QPSK and 64­QAM. The suggested nonlinear modelling results are used to get an accurate estimate of digital characteristics between PA amplifier and wireless multi­carrier transmission system using OFDM.

• Journal of Communications and Networks
• /
• v.18 no.2
• /
• pp.201-209
• /
• 2016

In wireless sensor networks (WSNs) duty cycling has been an imperative choice to reduce idle listening but it introduces sleep delay. Thus, the conventional WSN medium access control protocols are bound by the energy-latency tradeoff. To break through the tradeoff, we propose a radio wave sensor called radio frequency (RF) wakeup sensor that is dedicated to sense the presence of a RF signal. The distinctive feature of our design is that the RF wakeup sensor can provide the same sensitivity but with two orders of magnitude less energy than the underlying RF module. With RF wakeup sensor a sensor node no longer requires duty cycling. Instead, it can maintain a sleep state until its RF wakeup sensor detects a communication signal. According to our analysis, the response time of the RF wakeup sensor is much shorter than the minimum transmission time of a typical communication module. Therefore, we apply duty cycling to the RF wakeup sensor to further reduce the energy consumption without performance degradation. We evaluate the circuital characteristics of our RF wakeup sensor design by using Advanced Design System 2009 simulator. The results show that RF wakeup sensor allows a sensor node to completely turn off their communication module by performing the around-the-clock carrier sensing while it consumes only 0.07% energy of an idle communication module.

• Journal of Satellite, Information and Communications
• /
• v.10 no.3
• /
• pp.6-10
• /
• 2015

RF energy harvesting technology is a promising technology for generating the electrical power from ambient RF signal to operate low-power consumption devices(eg. sensor) in wireless communication networks. This paper, motivated by this and building upon existing CR(Cognitive Radio) network model, proposes a optimal control policy for RF energy harvesting CR networks model where secondary users that have low power consumption harvest ambient RF energy from transmission by nearby active primary users, while periodically sensing and opportunistically accessing the licensed spectrum to the primary user's network. We consider that primary users and secondary users are distributed as Poisson point processes and contact with their intended receivers at fixed distances. Finally we can derive the optimal frame duration, transmission power and density of secondary user from the proposed model that can maximize the secondary users's throughput under the given several conditions and suggest future directions of research.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.6
• /
• pp.25-29
• /
• 2017

This paper presents a hetero-integration of electrostatically actuated RF MEMS Switch and step up DC-DC converter on a redistribution layer using commercial PCB process. RF characteristics of Duroid with $56{\Omega}$ impedance GCPW transmission line and that of FR4 with $59{\Omega}$ impedance CPW transmission line were analyzed. From DC to 6GHz, RF characteristics of Duroid were better than that of FR4, insertion loss was 2.08dB lower, return loss was 3.91dB higher, and isolation was 3.33dB higher.

• Journal of Advanced Navigation Technology
• /
• v.14 no.5
• /
• pp.655-660
• /
• 2010

This paper examines RF-to-DC conversion efficiency of rectifying circuit for wireless power transmission. The rectifying circuit consists of low pass filter, diode circuits and dc pass filter. All these components may be effect on the conversion efficiency. Using the simulation, we study these components how to effect on the conversion efficiency. On the basis of the simulation results, the 912MHz rectifying circuit with 50% efficiency at low input power such as 0dBm is fabricated and its characteristics are measured.