• Journal of electromagnetic engineering and science
• /
• v.15 no.4
• /
• pp.250-257
• /
• 2015

This paper presents an experimental measurement system for 3-6 GHz microwave tomography (MT) of the breast. The measurement system is constructed as a minimal test bed to verify key components such as the sensing antennas, radio frequency (RF) transceiver, sensing mechanism, and image reconstruction method for our advanced MT system detecting breast cancer at an early stage. The test bed has eight RF channels operating at 3 to 6 GHz for high spatial resolution and a two-axis scanning mechanism for three-dimensional measurement. The measurement results from the test bed are shown and discussed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.4
• /
• pp.562-568
• /
• 2009

In this paper, using the periodic ground structure (PGS), highly miniaturized branch-line coupler and impedance transformer were realized on Si radio frequency integrated circuit (RFIC). The branch-line couple exhibited good RF performance from 41.75 to 50 GHz, and its size was $0.46{\times}0.55mm^2$, which is 37 % of conventional one. The impedance transformer exhibited good RF performance from 1 to 40GHz, and its size was $0.01mm^2$, which is 6.99 % of conventional one.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.1
• /
• pp.107-112
• /
• 2009

This paper describes design and fabrication issues of the SiP(System in Package) one-chip for a portable digital broadcasting receiver. It includes RF tuner chip, demodulator chip and passive components for the receiver system. When we apply the SiP one-chip technology to the broadcasting receiver, the system board size can be reduced from $776mm^2$ to $144mm^2$. SiP one-chip has an advantage that the area reduces more 81% than separated chips. Also the sensitivity performance advances -1dBm about 36 channels in the RF weak electric field, the power consumption reduces about 2mW and the C/N keeps on the same level.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.7
• /
• pp.1235-1240
• /
• 2008

In this paper, we presented an active RFID system in 2.45GHz range including LNA, Mixer and gain block. And in this work, a link budget model for RFID applications are proposed. We describe the detailed design and implementation of our system. Our components in RFID system has features such as low Noise Figure, reliable energy budget, and standard compliance with ISO 18000-4. Our receiver is effective for development and evaluation of prototype applications because of the flexibility of the design hardware. So, our platform will be suitable for versatile item management applications.

• Korean Journal of Food Science and Technology
• /
• v.35 no.5
• /
• pp.1003-1006
• /
• 2003

The quality of dried ginseng products (white ginseng, red ginseng, and taeguk ginseng) was investigated according to the National Standards. All the dried ginseng products met the general quality standard established: moisture content of 14.0% or less, ash content of 5.0% or less, and water-saturated n-butanol extracts of 2.0% or more. Ginsenoside $Rb_1$, Rf, and $Rg_1$, the effective components of Korean ginseng were detected by HPLC analysis. However, uniformity of individual products within a package was not kept for almost all of the products except for red ginseng products.

• Korean Journal of Crystallography
• /
• v.7 no.1
• /
• pp.1-7
• /
• 1996

We developed an automatic diameter control system to control the diameter of single crystal for Czochralski growth. The system is composed of load cell, software program and data acquisition system connected to computer which controls RF power. This study describes the basic principle, characteristics and components of the system. The diameter of Nd:YAG crystal could be controlled within ±5% tolerance by this system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.6A
• /
• pp.397-404
• /
• 2003

In this paper, we have analyzed the level of cross-modulation noise required for CDMA mobile station and proposed a guideline for optimum design. From the analysis, the level of cross-modulation noise is determined by the system's noise figure(NF) and VCO's phase noise and there is a trade-off relationships between them. In addition, we have determined the value of LNA's IIP3 and duplexer's isolation to satisfy the above level in designing the system. Therefore, this paper will give a guideline for a selection of components in designing cdma2000 mobile station.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.7 s.98
• /
• pp.753-759
• /
• 2005

In this paper, we have developed a new type of single balanced mixer with the RF MEMS $180^{\circ}$ hybrid coupler using surface micromachining technology. The $180^{\circ}$ hybrid coupler in this mixer is composed of the dielectric-supported air gapped microstriplines(DAMLs) which have signal line with $10{\mu}m$ height to reduce substrate dielectric loss and dielectric posts with size of $20{\mu}m{\times}20{\mu}m$ to elevate the signal line on air with stability At LO power of 7.2 dBm, the conversion loss was 15.5 dB f3r RF frequency or 57 GHz and RF power of -15 dBm. Also, we obtained the good RF to LO isolation of -40 dB at LO frequency of 58 GHz and LO power of 7.2 dBm. The main advantage of this type of mixer is that we are able to reduce the size of the chips due to integrating the MEMS passive components.

• ETRI Journal
• /
• v.38 no.5
• /
• pp.981-987
• /
• 2016

We present a cost-effective dual polarization quadrature phase-shift coherent receiver module using a silica planar lightwave circuit (PLC) hybrid assembly. Two polarization beam splitters and two $90^{\circ}$ optical hybrids are monolithically integrated in one silica PLC chip with an index contrast of $2%-{\Delta}$. Two four-channel spot-size converter integrated waveguide-photodetector (PD) arrays are bonded on PD carriers for transverse-electric/transverse-magnetic polarization, and butt-coupled to a polished facet of the PLC using a simple chip-to-chip bonding method. Instead of a ceramic sub-mount, a low-cost printed circuit board is applied in the module. A stepped CuW block is used to dissipate the heat generated from trans-impedance amplifiers and to vertically align RF transmission lines. The fabricated coherent receiver shows a 3-dB bandwidth of 26 GHz and a common mode rejection ratio of 16 dB at 22 GHz for a local oscillator optical input. A bit error rate of $8.3{\times}10^{-11}$ is achieved at a 112-Gbps back-to-back transmission with off-line digital signal processing.

• Korean Journal of Materials Research
• /
• v.22 no.2
• /
• pp.86-90
• /
• 2012

Insoluble catalytic electrodes were fabricated by RF magnetron sputtering of Pt on Ti substrates and the performance of seawater electrolysis was compared in these electrodes to that is DSA electrodes. The Pt-sputtered insoluble catalytic electrodes were nearly 150 nm-thick with a roughness of $0.18{\mu}m$, which is 1/660 and 1/12 of these values for the DSA (dimensionally stable anodes) electrodes. The seawater electrolysis performance levels were determined through measurements of the NaOCl concentration, which was the main reaction product after electrolysis using artificial seawater. The NaOCl concentration after 2 h of electrolysis with artificial seawater, which has 3.5% NaCl normally, at current densities of 50, 80 and 140 mA/$cm^2$ were 0.76%, 1.06%, and 2.03%, respectively. A higher current density applied through the electrodes led to higher electrolysis efficiency. The efficiency reached nearly 58% in the Pt-sputtered samples after 2 h of electrolysis. The reaction efficiency of DSA showed higher values than that of the Pt-sputtered insoluble catalytic electrodes. One plausible reason for this is the higher specific surface area of the DSA electrodes; the surface cracks of the DSAs resulted in a higher specific surface area and higher reaction sites. Upon the electrolysis process, some Mg- and Ca-hydroxides, which were minor components in the artificial seawater, were deposited onto the surface of the electrodes, resulting in an increase in the electrical resistances of the electrodes. However, the extent of the increase ranged from 4% to 7% within an electrolysis time of 720 h.