• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2003년도 춘계종합학술대회
• /
• pp.586-589
• /
• 2003

Repeater is developed. Based on the systems The up-converter of the WCDMA Digital Optic pecifications, the structure of the up-converter is accomplished and its block diagram is drawn. The up-converter is implemented according to these block diagrams. Subsequently the low pass filter, the automatic level controlled attenuator, the frequency synthesizer and other components for the up-converter are designed and implemented, and a main board to integrate these modules is also manufactured. To reduce the noise floor of system and suppress the RF spurious noise, a PCB layout is performed carefully. For each module consisting of the up-converter and the entire system, the performance tests are accomplished to check the performance about the specifications.

• ETRI Journal
• /
• 제32권5호
• /
• pp.827-830
• /
• 2010

For an adaptive cruise control (ACC) stop-and-go system in automotive applications, three radar sensors are needed because two 24 GHz short range radars are used for object detection in an adjacent lane, and one 77 GHz long-range radar is used for object detection in the center lane. In this letter, we propose a single sensor-based 24 GHz radar with a detection capability of up to 150 m and ${\pm}30^{\circ}$ for an ACC stop-and-go system. The developed radar is highly integrated with a high gain patch antenna, four channel receivers with GaAs RF ICs, and back-end processing board with subspace based digital beam forming algorithm.

• 한국항해학회지
• /
• 제19권3호
• /
• pp.29-34
• /
• 1995

IEC and CISPR have continuously endeavored the measurement method of Immunity Test as international unification, but not established yet. The main reason is that the measurement method and the normalization of threshold to obtain the complicated parameters for Immunity Test are difficult. Thus, the Immunity Test Setups are used differently according to the measured electromagnetic environments. This study developed an Immunity Test System and Algorithm for measurement software suitable for IEC801-3 Regulatons using ready-made amplifier, signal generator, and developes interconnecting interface board interacting with other appratus i.e., RF Switch, Power Meter, Field Sensor and Pre-amp. We are to develope an automated software using Top/Down and OOP(Object Oriented Programming) method.

• Journal of Electrical Engineering and Technology
• /
• 제11권1호
• /
• pp.175-183
• /
• 2016

This paper brings out a novel method for reducing Near end and Far end Crosstalk using Electromagnetic Band Gap structures (EBG) in High Speed RF transmission lines. This work becomes useful in high speed closely spaced Printed Circuit Board (PCB) traces connected to multi core processors. By using this method, reduction of −40dB in Near-End Crosstalk (NEXT) and −60 dB in Far End Crosstalk (FEXT) is achieved. The results are validated through experimental measurements. Time domain analysis is performed to validate the signal integrity property of coupled transmission lines.

• 제어로봇시스템학회논문지
• /
• 제16권4호
• /
• pp.374-380
• /
• 2010

This paper proposes a wearable interface for a tendon-driven robotic hand prosthesis. The proposed interface is composed of a dataglove to measure finger and wrist joint angle, and a micro-control board with a wireless RF module. The interface is used for posture control of the robotic hand prosthesis. The measured joint angles by the dataglove are transferred to the main controller via the wireless module. The controller works for directly controlling the joint angle of the hand or for recognizing hand postures using a pattern recognition method such as LDA and k-NN. The recognized hand postures in this study are the paper, the rock, the scissors, the precision grasp, and the tip grasp. In experiments, we show the performances of the wearable interface including the pattern recognition method.

• Journal of Welding and Joining
• /
• 제18권4호
• /
• pp.64-69
• /
• 2000

Reliability of PBGA(Plastic Ball Grid Array) package is very weak compared with normal plastic packages. The reliability are the lower resistance to popcorn cracking, which is reduced by moisture absorption in PCB(Printed Circuit Board). This paper adapts plasma treatment process and analyzes their effect. The contents of C and Cl decrease after plasma treatment but O, Ca and N relatively increase. The Plasma treatment to improve the adhesion between EMC(Epoxy Molding Compound) and PCB(solder mask). The degree of improvement was over 100% Max., which is depend on the properties of EMC. Ar+H$_2$as plasma gas show good result. There is a little difference in RF power and treatment time.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 춘계학술대회 논문집 반도체 재료 센서 박막재료 전자세라믹스
• /
• pp.150-152
• /
• 2004

The number of layers in rigid PCB(printed circuit board) is restricted, so the number of components can be embedded in module is restricted also. But using flexible multilayer PCB, the layers over than 7 can be evaluated. In this study, to verify the possibility of application of flexible multilayer PCB to RF modules, multilayered embedded capacitor is fabricated and analyzed. The characteristics of embedded capacitor is analyzed and compared to that of MLCC and LTCC capacitor. Embedded capacitor has better electrical features than MLCC and compatible one to LTCC capacitor.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.278-280
• /
• 2007

In this paper, wd design the Program Specific Information (PSI) parser and its On-Screen Display (OSD) on the middleware of ALi M3330 MPEG-2 decoder processor to analyze DVB-T Transport Stream(TS) information. To test the functional operation of the designed parser, we implement the DVB-T test board including the RF-tuner using ALi M3330 MPEP-2 decoder processor and confirm the correct operation using the input TS stream generated by DVB-T stream generator. The developed PSI parser could be used for the test environment, various channel extension, and the development of DVB-T reception module.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.169-171
• /
• 2007

This paper presents the development of DVB-T reception module including the RF-tuner. For the development of the reception module, we design the board using the ALi M3330 MPEG-2 decoder processor and implement its device driver. Simple On-Screen Display (OSD) applications are also designed on the middleware of ALi M3330 MPEG-2 decoder processor. To evaluate the performance of reception module, we test the decoding operations using the input TS stream generated by DVB-T stream generator and confirm the correctness of its functional operations.

• 센서학회지
• /
• 제16권4호
• /
• pp.247-253
• /
• 2007

Low power consumption sensor network platform (sensor node) for sensor networking with IEEE 802.15.4 protocol was fabricated. The sensor node used ceramic bar type antenna for increasing RF signal performance and decreasing PCB size occupied by antenna. The communication range of the fabricated sensor node was about $20{\sim}30$ m in open environment with 915 MHz frequency bandwidth and well supported by Tiny OS. The sensor node have good connectivity with various external devices by RS-232, I2C, analogue and digital expansion board, hence, this sensor node can be applied to various applications in wireless sensor network and ubiquitous sensor network.