• ETRI Journal
• /
• v.33 no.1
• /
• pp.6-12
• /
• 2011

A case study of an active transmitting patch antenna revealed a characteristic loop locus of DC power versus RF output power as drive frequency was varied, with an operational bandwidth substantially smaller than the impedance bandwidth of the radiator. An approximate simulation technique, based on separation of the output capacitance of the power transistor, yielded easily visualized plots of power dependence on internal load impedance, and a simple interpretation of the experimental results in terms of a near-resonance condition between the output capacitance and output packaging inductance.

• Journal of the Korean Vacuum Society
• /
• v.8 no.1
• /
• pp.75-82
• /
• 1999

Ion energy is one of the crucial property in thin film deposition by internal ICP assisted I-PVD. As ion energy is determined by the difference between the plasma potential and the substrate bias potential, ICP excitation frequency was tested with medium frequency of 4 MHz and two types of tuning circuits, alternate and floating LC network with a biasing resistor, were tested. The results showed that plasma potential was less than 5 V in a range of Ar pressures, 5mTorr to 30 mTorr, at 4 MHz RF 600 W and 60 V of maximum RF antenna voltage was maintained either at RF input or output terminal. By proper control of RLC circuit installed after after RF antenna, 50V of RF induced voltage on RF antenna was obtained at 500W input power. The total impedance of RF antenna and plasma was around 10$\Omega$, and minimum RF voltage was obtained with a condition of lowest reactance at most 0.05$\Omega$.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.9 no.6
• /
• pp.534-538
• /
• 2016

This paper discusses the characteristics and effects of dielectric inner-supports on discone antenna for broadband RF test chamber, and the verification has been performed by simulation. Several design parameters such as the thickness of the gap support, the position of the side support, and the thickness of the side support has been analyzed. The thickness of the gap support affected the reflection coefficient. An effect of the offset of the side support from the center was slight below 3 GHz and significant above 3 GHz. The thickness of the side support did not affect the reflection coefficient or the gain much. The performance of the fabricated discone antenna was in good agreement with the simulated results. This investigation of a dielectric support effects could be used to design a commercial discone antenna for broadband RF test chamber, focusing on electrical performance and mechanical stability.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.2A
• /
• pp.139-146
• /
• 2009

This paper presents an average internal loop-back antenna calibration method for array antenna in TDD(Time Division Duplex) systems. The proposed method calibrates the amplitude and the phase of RF systems using into mal coupler and switches without aids of external calibration systems. The average calibration scheme of the proposed method also increases reliability of calibration performance. Computer simulation demonstrates that the proposed method corrects beamforming angles of DOA estimation algorithm and BER performance in transmit power allocation scheme.

• Journal of Astronomy and Space Sciences
• /
• v.16 no.2
• /
• pp.191-198
• /
• 1999

Results of RF compatibility test between KOMPSAT(Korea Multi-Purpose SATellite) and TTC(Tracking, Telemetry, and Command) station are described. S/C(Spacecreft) RF Test, telemetry test, command test, ranging test, and tracking receiver test were performed with respect to pass/fail criteria. To provide physical RF interface between KOMPSAT and TTC equipment, direct low cable and antenna-to-antenna interface were implemented. Through RF compatibility test, it was fully demonstrated that KOMPSAT and TTC equipment are functionally workable.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.6
• /
• pp.603-611
• /
• 2008

In this paper, we introduce a multi-coil antenna which is useful for reducing the effects of radio frequency noise in an inductively coupled RFID system. A multi-coil antenna is composed of a central coil and four subsidiary coils that are connected in series. A multi-coil antenna is designed so that the total noise disappear when the induced voltages of a central coil and subsidiary coils are added. The noise in a multi-coil antenna was about 30 dB lower than that in a single coil antenna. The multi-coil antenna is very effective in noise reduction even in an environment that the spatial distribution of RF noise is changed abruptly, and the induced noise was about 16 dB lower than that in a dual coil antenna.

• Journal of Advanced Navigation Technology
• /
• v.25 no.5
• /
• pp.390-396
• /
• 2021

In this research, design and fabrication of marine repeater capable to extend communication coverage in monitoring system of fishing gear automatic identification, which is one of implementation method of the real-name electric fishing gear system declared by Ministry of Oceans and Fisheries in 2016, is reported. The proposed marine repeater is fabricated in a form of RF repeater with interference cancellation system (ICS), which can cancel the oscillation due to feedback signal between service antenna and link antenna. In design process, we secure the isolation of 30 dB between service antenna and link antenna. It is confirmed that when the level of feedback signal into repeater input be lower of 15 dB than repeater gain, error vector magnitude due to oscillation can be lower than the performance criterion of 6%, from the test verification. It is expected that the service coverage will be extended by applying the developed marine ICS RF repeater into marine IoT network including monitoring system of fishing gear automatic identification.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.4
• /
• pp.431-440
• /
• 2012

In this paper, new beam-forming array antenna is proposed. The proposed beam-forming array antenna has control ability for beam-direction/width by employing low loss reconfigurable power divide and three-dimensional array structure. The reconfigurable power divider is key idea in the proposed antenna, because it has reconfigurable RF power distribution ability to each antenna. And, for research and verification of the proposed antenna, 3-dimensional beam-forming array antenna is implemented, and the experimental results show that the proposed antenna has various radiation modes from 1:1 to 1:N by adjusting RF power distribution.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.5
• /
• pp.759-764
• /
• 2012

In this paper, we propose a microwave hyperthermic lipolysis method to reduce subcutaneous fat without skin burn using external RF antenna. Since skin is closer to the antenna and has higher conductivity compared to the fat beneath, the temperature of the skin rises higher than that of the fat when the external antenna illuminates EM energy into a body, which may cause skin burn. In order to avoid the damages on skin, a skin cooling system is employed to the external antenna. The operating frequency is set at 5.8 GHz which is one of the ISM bands, to concentrate EM power efficiently on fat and not to heat up the muscle behind the fat. The operation time and RF power level has been determined based on experimental results with pork. The feasibility of the proposed method was shown by applying the method to the rat.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.2
• /
• pp.148-157
• /
• 2015

In this paper, we propose a compact antenna hat to perform RF compatibility testing efficiently between the launch vehicle and ground stations. The proposed structure implements a small size and low loss using the conductive shield instead of the conventional RF absorber. The S-band antenna hat, which is fabricated for an inverted-F onboard antenna with the size of $74mm{\times}13mm{\times}16mm$, has the small enclosure of $88mm{\times}35mm{\times}44mm$, the return loss of 25.6 dB, the insertion loss of 0.26 dB, and the leakage loss of 49.4 dB at the center frequency of 2.25 GHz. The simulated and measured results show a good agreement.