• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1998.06a
• /
• pp.325-329
• /
• 1998

In this paper, the (Sr$_{1-x}$ Ca$_{x}$)TiO$_3$(SCT) thin films were deposited at various substrate temperature using RF magnetron sputtering method on optimized Pt-coated electrodes (Pt/TiN/SiO$_2$/Si). An influence of substrate temperature and annealing temperature on the structural and dielectric properties are investigated. The substrate temperature changed from 100[$^{\circ}C$] to 500[$^{\circ}C$] and crystalline SCT thin films were deposited abode 400[$^{\circ}C$]. All thin films had (111) preferred orientation, the (100) oriented films were obtained at the substrate temperature above 400[$^{\circ}C$]. The dielectric constant changes almost linearly in the temperature region of -80~+90[$^{\circ}C$], the temperature characteristics of the dielectric loss exhibited a stable value within 0.1, then not affected by substitutional contents. The capacitance characteristics appears a stable value within $\pm$5[%].

• Proceedings of the KIEE Conference
• /
• 1996.11a
• /
• pp.206-208
• /
• 1996

Thin films of magnesium oxide(MgO) were deposited on glass substrates by RF magnetron sputtering method. The characteristics of MgO thin films were analyzed as a function of various deposition conditions such as substrate temperature, substrate self-bias, input power and pressure. As the substrate temperature and bias voltage were increased, the grain size of MgO thin film increased. XRD peaks of (111) and (222) direction became dominant, as the substrate bias voltage increases and temperature decreases.

• Journal of the Korean Vacuum Society
• /
• v.18 no.3
• /
• pp.213-220
• /
• 2009

The optimal condition of low temperature deposition of transparent conductive Al-doped zinc oxide (AZO) films is studied by RF magnetron sputtering method. To achieve enhanced-electrical property and good crystallites quality, we tried to deposit on glass using a two-step growth process. This process was to deposit AZO buffer layer with optimal growth condition on glass in-situ state. The AZO film grown at rf 120 W on buffer layer prepared at RF $50{\sim}60\;W$ shows the electrical resistivity $3.9{\times}10^{-4}{\Omega}cm$, Carrier concentration $1.22{\times}10^{21}/cm^3$, and mobility $9.9\;cm^2/Vs$ in these results, The crystallinity of AZO film on buffer layer was similar to that of AZO film on glass with no buffer later but the electrical properties of the AZO film were 30% improved than that of the AZO film with no buffer layer. Therefore, the cause of enhanced electrical properties was explained to be dependent on degree of crystallization and on buffer layer's compressive stress by variation of $Ar^+$ ion impinging energy.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.953-956
• /
• 2003

Transparent conductive ZnO:Ga thin films were deposited on glass substrates using rf magnetron sputtering method for flat panel display. The ZnO:Ga films were preferentially oriented to c-axis (002) of on substrates. The surface morphology was smooth and had not porous whatever substrate temperature was. The electrical conductivity of the thin films were in the range of $1.6{\times}10^2{\sim}6.7{\times}10^3\;{\Omega}^{-1}cm^{-1}$ at the growth temperature from 50 to $400^{\circ}C$, whereas has a maximum at around $250^{\circ}C$. By combining of XRD and EXAFS, the crystallinity and grain size decreased with increasing substrate temperature corresponding to the reduction of the grain-boundary scattering. The optical transmittance of sputtered ZnO:Ga thin films had an improved about 86% in the UV-visible region.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.6
• /
• pp.829-833
• /
• 1996

Superconducting YBaCuO thin films were deposited on MgO (100) single crystal substrate by rf reactive sputtering method. Sputtering target was prepared by mixing the original powders of $Y_2O_3$, $BaCO_3$, and CuO at $830^{\circ}C$, and its composition was $YBa_2Cu_{3.3}O_x$ adding the excess CuO to compensate for the loss of Cu in the deposition process. The sputtering conditions for a high quality of YBCO thin film were: substrate temperature of 13$0^{\circ}C$; gas pressure of 10 mTorr; gas mixture ($O_2$: Ar =10: 90); distance of 2.5 inch; and rf power density of 4.87 W /$\textrm{cm}^2$. The deposition rate was 2.4~2.6 nm/min. From the RBS results, it was found that Cu and Ba contents in thin films decreased with the increase of substrate temperature. The increase of gas pressure resulted in significant deficiency of Ba elements.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.446-447
• /
• 2007

The rapid thermal annealing effect of transparent IZTO(indium zinc oxide) and IAZO(indium alminium zinc oxide) films grown on glass substrate for solar cell or flat panel displays(FPDs) was studied. We prepared IZTO using RF magnetron sputtering and IAZO using DC co-sputtering method. Subsequently, using rapid thermal annealing(RTA) system, prepared IZTO and IAZO films were annealed at 300, 400, 500, $600^{\circ}C$ for 90sec. In addition, Electrical and optical characteristics were measured by Hall effect measurement and UV/Vis spectrometer examinations, respectively. To analyze structural properties and surface smoothness of the IZTO and IAZO films, XRD and SEM examinations were performed, respectively. It was shown that IZTO and IAZO films exhibited microcrystalline structure over $400^{\circ}C$ and amorphous structural regardless of RTA temperature, respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.06a
• /
• pp.120-121
• /
• 2006

To investigate the ZnO thin films which are interested in the next generation of short wavelength LEDs and Lasers, the ZnO thin films were deposited by RF magnetron sputtering system. Al sputtering process of ZnO thin films substrate temperature, work pressure respectively is $100^{\circ}C$ and 15 mTorr, and the purity of target is ZnO 5N. The ZnO thin films were in-situ annealed at $600^{\circ}C$, $800^{\circ}C$ in $O_2$ atmosphere. Phosphorus (P) and arsenic (As) were diffused into ZnO thin films sputtered by RF magnetron sputtering system in ampoule tube which was below $5{\times}10^{-7}$ Torr. The dopant sources of phosphorus and arsenic were $Zn_3P_2$ and $ZnAS_2$. Those diffusion was perform at $650^{\circ}C$ during 3hr. We confirmed that p-type properties of ZnO thin films were concerned with dopant sources rather than diffusion temperature.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.2
• /
• pp.73-78
• /
• 2004

AIN thin film has been deposited on the $AI_2$$O_3$substrate with reactive radio frequency( RF) magnetron sputtering method. In this work, elelctromechanical coupling coefficient of AIN thin film was increased with an increase of AIN thin film thickness, and the maximum value was 0.11%. Insertion loss of SAW device was decreased with an increase of AIN thin film thickness and the minimum value was 33［㏈］. SAW velocity of IDTs/AIN/$AI_2$$O_3$structure and IDTs/AIN/$AI_2$$O_3$/Si structure were about 5480［㎧］and 5040［㎧］respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.175.1-175.1
• /
• 2015

CuSn thin films were deposited by rf magnetron co-sputtering method with pure Cu and Sn metal targets with a variety of rf powers. CuSn thin films were studied with a surface profiler (alpha step), X-ray photoelectron spectroscopy (XPS), X-ray induced Auger electron spectroscopy (XAES), X-ray diffraction (XRD), and contact angle measurement. The thickness of CuSn thin films was fixed at $200{\pm}10nm$ and deposition rate was calculated by the measured with a surface profiler. From the survey XPS spectra, the characteristic peaks of Cu and Sn were observed. Therefore, CuSn thin films were successfully synthesized on the Si (100) substrate. The oxidation state and chemical environment of Cu and Sn were investigated with the binding energy regions of Cu 2p XPS spectra, Sn 3d XPS spectra, and Cu LMM Auger spectra. Change of the crystallinity of the films was observed with XRD spectra. Using contact angle measurement, surface free energy (SFE) and wettability of the CuSn thin films were studied with distilled water (DW) and ethylene glycol (EG).

• Journal of Electrical Engineering and Technology
• /
• v.2 no.1
• /
• pp.98-101
• /
• 2007

Yttrium(Y)-substituted bismuth titanate $(Bi_{4-x},Y_x)Ti_3O_{12}$ [x=0, 0.25, 0.5, 0.75, 1](BYT) thin films were deposited using an RF sputtering method on the $Pt/TiO_2/SiO_2/Si$ substrates. The structural properties and electrical properties of yttrium-substituted $(Bi_4-xYx)Ti_3O_{12}$ thin films were analyzed. The remanent polarization of $(Bi_4-xYx)Ti_3O_{12}$ films increased with increasing Y-content. The $(Bi_{3.25}Y_{0.75})Ti_3O_{12}$ films fabricated using a top Au electrode showed saturated polarization-electric field(P-E) switching curves with a remanent polarization(Pr) of $8{\mu}C/cm^2$ and coercive field (Ec) of 53 kV/cm at an applied voltage of 7 V. The $(Bi_{3.25}Y_{0.75})Ti_3O_{12}$ films exhibited fatigue-free behavior up to $4.5{\times}10^{11}$ read/write switching cycles at a frequency of 1MHz.