• Journal of Sensor Science and Technology
• /
• v.12 no.6
• /
• pp.265-272
• /
• 2003

This paper describes anodic bonding characteristics of MLCA (Multi Layer Ceramic Actuator) to Si-wafer using evaporated Pyrex #7740 glass thin-films for MEMS applications. Pyrex #7740 glass thin-films with same properties were deposited on MLCA under optimum RF magneto conditions(Ar 100%, input power $1\;W/cm^2$). After annealing in $450^{\circ}C$ for 1 hr, the anodic bonding of MLCA and Si-wafer was successfully performed at 600 V, $400^{\circ}C$ in - 760 mmHg. Then, the MLCA/Si bonded interface and fabricated Si diaphragm deflection characteristics were analyzed through the actuation test. It is possible to control with accurate deflection of Si diaphragm according to its geometries and its maximum non-linearity is 0.05-0.08 %FS. Moreover, any damages or separation of MLCA/Si bonded interfaces do not occur during actuation test. Therefore, it is expected that anodic bonding technology of MLCA/Si wafers could be usefully applied for the fabrication process of high-performance piezoelectric MEMS devices.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.265.2-265.2
• /
• 2016

Oxide thin film transistors (TFTs) have attracted considerable interest for gate diver and pixel switching devices of the active matrix (AM) liquid crystal display (LCD) and organic light emitting diode (OLED) display because of their high field effect mobility, transparency in visible light region, and low temperature processing below $300^{\circ}C$. Recently, oxide TFTs with polycrystalline In-Ga-O(IGO) channel layer reported by Ebata. et. al. showed a amazing field effect mobility of $39.1cm^2/Vs$. The reason having high field effect mobility of IGO TFTs is because $In_2O_3$ has a bixbyite structure in which linear chains of edge sharing InO6 octahedral are isotropic. In this work, we investigated the characteristics and the effects of oxygen partial pressure significantly changed the IGO thin-films and IGO TFTs transfer characteristics. IGO thin-film were fabricated by rf-magnetron sputtering with different oxygen partial pressure ($O_2/(Ar+O_2)$, $Po_2$)ratios. IGO thin film Varies depending on the oxygen partial pressure of 0.1%, 1%, 3%, 5%, 10% have been some significant changes in the electrical characteristics. Also the IGO TFTs VTH value conspicuously shifted in the positive direction, from -8 to 11V as the $Po_2$ increased from 1% to 10%. At $Po_2$ was 5%, IGO TFTs showed a high drain current on/off ratio of ${\sim}10^8$, a field-effect mobility of $84cm^2/Vs$, a threshold voltage of 1.5V, and a subthreshold slpe(SS) of 0.2V/decade from log(IDS) vs VGS.

• Korean Journal of Materials Research
• /
• v.30 no.10
• /
• pp.558-565
• /
• 2020

AZO thin films are grown on a p-Si(111) substrate by RF magnetron sputtering. The characteristics of various thicknesses and heat treatment conditions are investigated by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Hall effect and room-temperature photoluminescence (PL) measurements. The substrate temperature and the RF power during growth are kept constant at 400 ℃ and 200 W, respectively. AZO films are grown with a preferred orientation along the c-axis. As the thickness and the heat treatment temperature increases, the length of the c-axis decreases as Al³⁺ ions of relatively small ion radius are substituted for Zn²⁺ ions. At room temperature, the PL spectrum is separated into an NBE emission peak around 3.2 eV and a violet regions peak around 2.95 eV with increasing thickness, and the PL emission peak of 300 nm is red-shifted with increasing annealing temperature. In the XPS measurement, the peak intensity of Al_2p and O_ll increases with increasing annealing temperature. The AZO thin film of 100 nm thickness shows values of 6.5 × 10¹⁹ cm^-3 of carrier concentration, 8.4 cm^-2/V·s of mobility and 1.2 × 10^-2 Ω·cm electrical resistivity. As the thickness of the thin film increases, the carrier concentration and the mobility increase, resulting in the decrease of resistivity. With the carrier concentration, mobility decreases when the heat treatment temperature increases more than 500 ℃.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.393-396
• /
• 2004

본 논문에서는 완충층용 MgO 박막을 P-type(100)Si 기판위에 작업가스 $Ar:O_2=80:20$, RF 파워 50W, 기판온도 $400^{\circ}C$, 10mtorr의 작업진공에서 $500{\AA}$ 증착하였다. 제작된 MgO/Si 기판위에 RF Magnetron sputtering법으로 작업가스 $Ar:O_2$의 비율을 90:10, 80:20, 70:30으로 변화하면서 $BST(Ba_{0.5}Sr_{0.5}TiO_3)$ 박막을 약 $2000{\AA}$ 증착하였다. XRD 측정결과 작업가스비의 변화에 관계없이(110)BST와 (111)BST 피크만이 관찰되었으며 작업가스 $Ar:O_2=80:20$에서 가장 양호한 결정성을 나타내었다. I-V 측정결과 인가전계 ${\pm}100kV/cm$에서 $10^{-7}A/cm^2$이하의 양호한 누설전류 특성을 보여주고 있으며 C-V 측정결과 작업가스 $Ar:O_2$의 비율 90:10, 80:20, 70:30에서의 비유전율은 각각 283, 305, 296으로서 작업가스비 80:20에서 제작된 박막의 특성이 가장 우수하였다. 작업가스비 80:20에서 제작된 박막의 SEM 측정결과 결정이 성장되었음을 확인할 수 있었고 그레인의 크기는 약 10nm였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.10
• /
• pp.859-863
• /
• 2007

Aluminum oxide films were deposited on n-type 6H-SiC(0001) substrates by RF magnetron sputtering technique for MIS devices applications. Well-behaved C-V characteristics were obtained measured in MIS capacitors structures. The calculated interface trap density measured at $300^{\circ}C$ was about $4.6{\times}10^{10}/cm^2\;eV$ in the upper half of the bandgap. The gate leakage current densities of the MIS structures were about $10^{-8}A/cm^2$ and about $10^{-6}A/cm^2$ measured at room temperature and at $300^{\circ}C$ for a ${\pm}1\;MV/cm$, respectively These results indicate that the interface property of this structure is enough quality to MIS devices applications.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.05a
• /
• pp.152-155
• /
• 2006

Carbon nitride ($CN_X$) films were prepared by reactive RF magnetron sputtering system at various deposition conditions and the C-V characteristics of MIS(metal - insulator - semiconductor) capacitors that have the structures of Al/$CN_x$/p-Si/Al and Al/$CN_x$/$Si_3N_4$/p-Si/Al were investigated. The resistivity of carbon nitride was above $2.40{\times}10^8{\Omega}{\cdot}cm$ at room temperature. The C-V plot showed a typical capacitance-voltage characteristics of semiconductor insulating layers, while it showed hysterisis due to interface charges. Amorphous carbon nitride (a-$CN_x$) films, that have relatively high resistivity and low dielectric constant could be useful as interlayer insulator materials of VLSI(very large-scale integration) and ULSI(ultra large-scale integration).

• The Korean Journal of Pain
• /
• v.14 no.2
• /
• pp.261-265
• /
• 2001

Radiofrequency thermocoagulation of the gasserian ganglion is a safe procedure that can be controlled well and provides satisfactory pain relief from trigeminal neuralgia with low risk. Here the authors report a case of radiofrequency thermocoagulation performed on a recurred trigeminal neuralgia patient, with particular attention to the V3 area. The patient was treated with microvascular decompression 7 years previous, which lead to untolerable side effects from carbamazepine medication. Following the paresthesia and masseter muscle contracture test at 50 Hz-0.06 volt and 2 Hz-0.5 volt respectively, RF lesionings were performed for 60 sec at $60^{\circ}C$ and 70 sec at $70^{\circ}C$. One week after the procedure, the pain was reduced with a mild hypoesthesia in the V2 area. After 6 months, the pain recurred. Therefore, we performed the same procedure again. After 8-months of follow-up, there has been no pain or complications.

• Proceedings of the IEEK Conference
• /
• 1998.06a
• /
• pp.461-464
• /
• 1998

Self-aligned AlGaAs/GaAs HBTs with the emitter area of 1.5*10.mu.$m^{2}$ were fabricated usng $WN_{x}$ as emitter metal. Their DC and RF characteristics were investigated. The common emitter current gain was 45 at $J_{c}$ = 6*$10^{4}$A/$cm^{2}$. From the Gummel plot, the ideality factors of $I_{c}$ and $I_{B}$ were 1.18 and 1.70, respectively. Emitter and base resistance were extracted from voltage drop region in gummel plot, and their values were 5.3.ohm. and 38.2.ohm.. The extrapolated $f_{T}$ = 72GHz and $f_{max}$ = 81GHz were obtained at $V_{CE}$ = 2V.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1992.05a
• /
• pp.114-116
• /
• 1992

ITO/TiO$_2$/Se solar cell were fabricated by vacuum deposition method, the Se and TiO$_2$were deposited on the ITO/Glass. Prior to the electrical properties of film, the provide Te between the ITO and the Se film were deposited by substrate temperature 20[$^{\circ}C$] and evaporation time 15[min], next time TiO$_2$ were treated by rf-magnetron sputtering in substrate temperature 250[$^{\circ}C$]. Fabricated ITO/TiO$_2$/Se solar cell were as follows : Open Voltage V$\_$oc/=848[mV], Short Circuit Current I$\_$sc/=10.79[mA/$\textrm{cm}^2$]. Fill Factor FF=0.518, energy conversion efficiency η=4.74[%] under the illumination of AM 1.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.175-175
• /
• 2011

인체감지 적외선 센서로 사용되는 마이크로볼로미터 센서 감지재료인 $V_{2-x}W_xO_5$를 증착하고 단위소자를 제작하여 저항 및 센서성능을 측정 조사하였다. 감지재료는 $V_2O_5$에 W을 첨가하여 $V_{2-n}W_nO_5$ 타겟을 제작하였으며 RF sputtering 장비를 이용하여 $V_{1.85}W_{0.15}O_5$ 박막을 증착하였다. 증착온도 $400^{\circ}C$, $Ar/O_2$ 가스비율 50/20, 두께 200nm로 증착된 센서 재료의 특성을 조사한 결과 저항은 약 $20{\sim}70k{\Omega}$이었으며, TCR 값은 -3%/$^{\circ}C$ 이상으로 매우 우수한 박막특성을 얻었다. 볼로미터소자는 $40{\times}40{\sim}140{\times}140um^2$의 셀면적으로 설계하여 전극패턴과 습식식각공정으로 센서 구조체를 제작하였다. 소자의 성능평가는 검출기 측정장비를 이용하여 반응도 및 탐지도 특성을 조사하였다.