• Journal of Mechanical Science and Technology
• /
• 제14권9호
• /
• pp.978-984
• /
• 2000

The aim of this study is to investigate the ductile fracture behaviour under Mode I loading using SA533B pressure vessel steel. Experiments consist of the Round Notch Bar Test (RNB), Single Edge Crack Bending Test (SECB), and V-Notch Bar Test (VNB). Results from the RNB test were used to tune the damage modelling constant. The other tests were performed to acquire the J-resistance curves and to confirm the damage constants. Microstructural observation includes the measurement of crack profile to obtain the roughness parameter. Finally, simulation using Rousellier Ductile Damage Theory (RDDT) was carried out with 4-node quadrilateral element ($L_c=0.25\;mm$). For the crack advance, the failed element removal technique was adopted with a ${\beta}$ criterion. In conclusion, the predicted simulation using RDDT showed a good agreement with the experimental results. A trial using a roughness parameter was made for a new evaluation of J-resistance curve, which is more conservative than the conventional one.

• Structural Engineering and Mechanics
• /
• 제41권2호
• /
• pp.205-229
• /
• 2012

This paper presents a new nine-node Lagrangian quadrilateral plate bending element (MQP9) using the Integrated Force Method (IFM) for the analysis of thin and moderately thick plate bending problems. Three degrees of freedom: transverse displacement w and two rotations ${\theta}_x$ and ${\theta}_y$ are considered at each node of the element. The Mindlin-Reissner theory has been employed in the formulation which accounts the effect of shear deformation. Many standard plate bending benchmark problems have been analyzed using the new element MQP9 for various grid sizes via Integrated Force Method to estimate defections and bending moments. These results of the new element MQP9 are compared with those of similar displacement-based plate bending elements available in the literature. The results are also compared with exact solutions. It is observed that the presented new element MQP9 is free from shear locking and produced, in general, excellent results in all plate bending benchmark problems considered.

• 대한토목학회논문집
• /
• 제14권3호
• /
• pp.439-452
• /
• 1994

본 논문에서는 동적하중을 받는 철근 콘크리트 뼈대구조의 경비 최적설계방법과 한계상태 설계 최적화 알고리즘을 제시하였다. 뼈대구조의 동적반응은 모드 중첩법을 이용하여 해석하였으며 뼈대구조의 각 부재를 두 개 이상의 요소로 구성하여 각 요소의 절점에서는 축방향, 횡방향 및 휨방향의 거동을 규명할 수 있도록 3 d.o.f(자유도)로 구성된 강성 매트릭스와 질량 매트릭스를 사용하였다. 철근과 콘크리트의 주 재료 경비로 유도한 목적함수는 한계 상태 설계 규정에 따라 철근 콘크리트 뼈대구조의 역학적 거동의 문제와 사용성 제약조건을 만족하면서 최적화를 이루도록 하였다. 목적함수와 제약조건은 단면의 유효깊이, 보의 폭, 인장과 압축 철근의 단면적, 기둥의 전단 철근 단면적들의 설계변수로 유도하였으며 최적화 문제를 형성하였다. 몇가지 예제를 통하여 동적거동을 고려한 철근 콘크리트 뼈대구조의 자동화된 최적 설계 알고리즘의 가능성, 타당성 및 효율성을 검토하였다.

• 한국가스학회지
• /
• 제20권4호
• /
• pp.78-84
• /
• 2016

대용량 알루미늄 라이너의 제작을 위해 역 드로잉 공정을 적용하였고, 최적의 역 드로잉 공정 설계에 대한 연구를 수행하였다. $350^{\circ}C$의 어닐링된 Al6061의 인장시험 및 해석을 수행하여 라이너 성형 해석을 위한 대변형률에서의 유동응력 및 연성파괴지수를 구하였다. 역드로잉 공정의 유한요소해석을 수행하여 금형의 형상, 블랭크 홀딩력, 드로잉비, 금형간의 간격, 부분가열영향에 대해 분석하였다. 유한요소해석을 통해 주름 및 파단을 방지하는 최적의 조건을 도출하여 시제품을 제작하였으나, 드로잉된 컵의 끝부분에서 부분적인 파단이 발생하였다. 하지만 후속공정을 적용하기 위한 충분한 길이가 확보되어 플로우 포밍, 스피닝 공정을 적용하여 최종제품을 제작하였다.

• 한국양식학회:학술대회논문집
• /
• 한국양식학회 2003년도 추계학술발표대회 논문요약집
• /
• pp.88-89
• /
• 2003

Rotifer의 먹이 생물로 이용되는 Chlorella의 대량 배양에는 농업용 비료가 널리 이용되고 있다. 그러나 농업용 비료만을 사용할 경우 f/2배지에 비해 성장이 낮은 단점이 있다. 따라서 본 연구는 농업용 비료 배지에 여러 가지 미량 성분을 첨가하여 그 성장 변화를 측정하고, 고밀도 대량 배양에 필요한 미량 원소 성분을 파악하고자 하였다. 먼저 Chlorella의 대량 배양에 이용되는 농업용 비료 배지(복합, 요소비료)에 실내 배양에 주로 이용되는 f/2배지의 trace element 성분 중 코발트(Co), 구리(Cu), 아연(Zn) 및 몰리브덴(Mo)를 f/2배지의 함량을 기준으로 각각 0.5, 1.0, 1.5 및 2.0배로 첨가하여 $25^{\circ}C$, 5,000 lux 연속조명, 15$\textperthousand$에서 배양한 결과 각 미량 원소의 첨가 함량이 높을수록 Chlorella의 성장은 높게 나타났다. 전체 실험구 중에서 아연 2.0배, 구리 2.0배를 첨가한 비료 배지에서 S.G.R.이 각각 0.3598, 0.3599의 성장을 나타내었으며, 아연과 구리 성분을 첨가한 Chlorella에서 높은 성장률을 보였다. 위의 실험에서 첨가효과가 좋은 Cu와 Zn 2.0배와 철(Fe)과 망간(Mn)을 같은 비율(0.5~2.0배)로, 다시 배양한 결과, Cu 2.0배와 Zn 2.0배는 S.G.R.이 각각 0.6283과 0.6231로 가장 높았으며, Fe 2.0배, Mn 2.0배와 1.5배에서 S.G.R이 각각 0.6210, 0.6200, 0.6183의 높은 성장률을 나타내었다. 위의 실험에서 농업용 비료에 첨가된 모든 trace element 중에서 가장 좋은 성장을 나타낸 구리(Cu) 성분의 정확한 공급 농도를 파악하기 위하여 농업용 비료에 2, 3, 4 및 5배를 첨가하여 $25^{\circ}C$, 5,000 lux, 15$\textperthousand$에서 배양한 결과, S.G.R.이 CU 함량을 3배로 첨가하였을 경우 2716$\times$$10^4$cells/$m\ell$로 가장 높은 세포 밀도를 나타내었다. 또한 5종의 trace element (Fe, Mn, Zn, Cu, Co)를 혼합하여 비료 배지(1.25배)에 첨가하여 미량 원소간의 상호 작용에 대해서 알아 본 결과, Fe와 Mn 두가지 성분만을 농업용 비료 배지에 혼합하였을 경우 세포수가 2720$\times$$10^4$cells/$m\ell$로서 높은 성장을 나타내었다. 다음으로 Fe, Mn, Zn 및 Cu 4종을 모두 혼합하여 첨가한 실험구가 2608$\times$$10^4$ cells/$m\ell$ 높은 세포 밀도를 나타내었다. 이러한 결과로서 옥외에서 농업용 비료배지에 구리(Cu, f/2배지 기준 3.0배)성분을 첨가함으로써 Chlorella의 성장을 효율적으로 향상시킬 수 있을 것으로 판단된다.

• 대한수학회논문집
• /
• 제33권2호
• /
• pp.379-395
• /
• 2018

Assume that R is a commutative ring with non-zero identity which is not an integral domain. An ideal I of R is called an annihilating ideal if there exists a non-zero element $a{\in}R$ such that Ia = 0. S. Visweswaran and H. D. Patel associated a graph with the set of all non-zero annihilating ideals of R, denoted by ${\Omega}(R)$, as the graph with the vertex-set $A(R)^*$, the set of all non-zero annihilating ideals of R, and two distinct vertices I and J are adjacent if I + J is an annihilating ideal. In this paper, we study the relations between the diameters of ${\Omega}(R)$ and ${\Omega}(R[x])$. Also, we study the relations between the diameters of ${\Omega}(R)$ and ${\Omega}(R[[x]])$, whenever R is a Noetherian ring. In addition, we investigate the relations between the diameters of this graph and the zero-divisor graph. Moreover, we study some combinatorial properties of ${\Omega}(R)$ such as domination number and independence number. Furthermore, we study the complement of this graph.

• 소성∙가공
• /
• 제22권6호
• /
• pp.317-322
• /
• 2013

A radio frequency(R/F) switch connector is widely used in wireless devices such as mobile phone and navigator to check defects of the circuit board of product. The R/F switch connector shell plays a role in protecting the switch connector. Previously, this part was machined using a turning, which is time-consuming and has poor material utilization. Furthermore, the workpiece material of brass containing lead that has excellent machinability has environmentally regulated during recent years. The purpose of the current study was to develop the connector shell by forming through progressive dies including embossing, burring and forging process in order to achieve higher productivity and dimensional accuracy without tool failure. To accomplish this objective, a strip layout was designed and finite element (FE) analysis was performed for each step in the process. Try-out for the connector shell was conducted using progressive die design based on FE-analysis results. Dimensional accuracy of developed part was investigated by scanning electron microscopy. The result of the investigation for the dimensions of the formed connector shell showed that the required dimensional accuracy was satisfied. Moreover, productivity using the progressive die increased four times compared to previous machining process.

• Geomechanics and Engineering
• /
• 제9권4호
• /
• pp.415-426
• /
• 2015

Researches have been done to discover ways to strengthen peat soil deposits. In this model study, fibrous peat that is the most compressible types of peat has been reinforced with precast peat columns stabilized with ordinary Portland cement and polypropylene fibres. Rowe cell consolidation tests as well as plate load tests (PLTs) were conducted on various types of test samples to evaluate the strength and deformation of untreated peat and peat reinforced by various types of columns. PLTs were conducted in a specially designed and fabricated circular steel test tank. The compression index ($C_c$) and recompression index ($C_r$) of fibrous peat samples reduced considerably upon use of precast columns. Also, PLT results confirmed the results obtained from Rowe cell tests. Use of polypropylene fibres added to cement further decreased ($C_c$) and ($C_r$) and increased load bearing capacity of untreated peat. Finite element method (FEM) using Plaxis 3D was carried out to evaluate the stress distributions along various types of tested samples and also, to compare the deformations obtained from FEM analysis with the actual maximum deformations found from PLTs. FEM results indicate that most of the induced stresses are taken on the upper portion of tested samples and reach their maximum values below the loading plate. Also, a close agreement was found between actual deformation values obtained from PLTs and values resulted from FEM analysis for various types of tested samples.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.1688-1690
• /
• 1996

In this paper, by using the Finite Element Method, we analysed the melting and clearing characteristic of fuse elments shapes. The melting characteristics and the effects of temperature conduction by fuse element shames was studied. We compared the actul testing results by the clearing device with the simulation result.

• 소성∙가공
• /
• 제17권8호
• /
• pp.649-656
• /
• 2008

Springback is one of factors affecting precision in metal forming. Its effect is particularly prominent in bending process. In this study, bending and forging process are used in order to manufacture a micro spring with two bending region from $60{\mu}m$ diameter wire. Springback in the process lowers the precision of the micro spring. Overbending for springback compensation has wide usage in a general way. However, this method requires repeated modifications of press dies until the tolerance is allowable, which causes that production cost and time increase. In this paper, we analyzed the mechanism of springback in the forming process of the micro spring using finite element method. In addition, a simple method to control springback without modifying dies was proposed by performing numerical analysis with various parameters.