• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.152-159
• /
• 1999

YBa$_2Cu_3O_{7-{\delta}}$ (YBCO) films grown on CeO$_2$-buffered r-cut sapphire substrates (CbS's) were prepared and their structural and electrical properties were measured. Post-annealed CeO$_2$ films were used as buffer layers for the experiments. It turned out that the YBCO films grown on post-annealed CbS's had the rms roughness of less than 20 ${\AA}$ and peak-to-peak roughness of about 30 ${\AA}$ when the YBCO film thickness was 3000 ${\AA}$. Meanwhile, YBCO films on in-situ grown CeO$_2$ buffer layers on r-cut sapphire substrates appeared to have the peak-to-peak roughness of more than 450 ${\AA}$. X-ray diffraction data revealed that the YBCO flms were epitaxially grown along the c-axis with the typical FWHM of(005) ${\theta}$ -2 ${\theta}$ peak about 0. 16 $^{\circ}$ and ${\Delta}$ ${\omega}$ of the (005) peak about 0.5 $^{\circ}$. T$_c$ > 87 K, ${\Delta}$T < 1 K and R(look)/R(100K) ${\ge}$3 were observed from the YBCO films. Applicability of the YBCO films for high-frequency applications was described.

• Nuclear Engineering and Technology
• /
• v.54 no.2
• /
• pp.462-468
• /
• 2022

The selection and effective utilization of peak-fitting software for conventional gamma-ray spectrum analysis is significant for accurate determination of the mass fraction of elements, particularly in complex peak regions. Majority of the peak-fitting programs can derive similar peak characteristics for singlet peaks, but very few programs can deconvolute multi-peaks in a complex region. The deconvolution of multi-peaks requires special peak-fitting functions, such as left and right-skew distributions. In the this study, 843.76 keV (²⁷Mg) peak area from the complex region (840 keV-850 keV) determined and compared using four different peak-fitting programs, namely, GammaVision, Genie2000, HyperLab, and HyperGam. The 843.76 keV peak interfered with 841.63 keV (^152mEu) and 846.81 keV (⁵⁶Mn). The total Mg concentration was determined through k₀-instrumental neutron activation analysis by applying the isotopic interference correction factor ²⁷Al(n,p)²⁷Mg through the simultaneous determination of Al concentration. HyperLab and HyperGam peak-fitting programs reported consistent peak areas, and resultant concentrations agreed with the certified values of matrix-certified reference materials.

• Physical Therapy Korea
• /
• v.14 no.4
• /
• pp.84-90
• /
• 2007

The purpose of this study was to assess the test-retest reliability of heart rate (HR) and velocity measurements during peak effort and free treadmill walking tests in older patients with gait-impaired chronic hemiparetic stroke and control group. Twenty-two adults (13 men, 9 women; mean age, $73.7{\pm}5.2$ yrs) with chronic hemiparetic stroke are the experimental group. Nineteen elderly people (5 men, 14 women; mean age, $72.3{\pm}3.5$ yrs) were recruited as control group. Patients had mild to moderate chronic hemiparetic gait deficits, making handrail support necessary during treadmill walking. Free and peak effort treadmill walking tests were measured and then repeated at least two days later. Reliability was calculated from HR and walking velocity during free and peak effort treadmill walking test. Among the people who had strokes, HR [ICC(2,1)=.85, r=.86] and velocity [ICC(2,1)=.93, r=.93] were good parameters during free testing. Maximal testing generated good results for HR [ICC(2,1)=.81, r=.82] and velocity [ICC(2,1)=.96, r=.96] with the chronic hemiparetic stroke. In elderly people, HR [ICC(2,1)=.59, r=.62] and velocity [ICC(2,1)=.77, r=.76] were moderately reliable during free testing. Maximal testing produced moderate parameters for HR [ICC(2,1)=.74, r=.74] and velocity [ICC(2,1)=.66, r=.66] in the elderly. This study provides that free and maximal treadmill testing produce highly reliable HR and velocity measurements in adults with chronic hemiplegia using minimal handrail support.

• Journal of agriculture & life science
• /
• v.50 no.5
• /
• pp.173-182
• /
• 2016

This study was aimed to identify the phenotypic relationships between calving interval and lactation curve parameters in Korean Holstein cow. The data of 36,505 lactation records was obtained from the Dairy Herd Improvement program run by Dairy Cattle Improvemnet Center of National Agricultural Federation of Korea. All lactation records were collectied from the multiparous cows calving between 2011 to 2013. The estimated lactation curves were drawn using Wood model based on actual milk yield records, and NLIN Procedure of SAS program (ver. 9.2). General linear multivariate models for calving interval, 305-d milk yield, lactation parameters(A, b, c), persistency, peak day, and peak yield included fixed effects of calving year-season (spring, summer, fall and winter) and parity(2, 3 and 4). For calving interval, 305-d milk yield, lactation parameters(A, b, c), persistency, peak day and peak yield, all two fixed effect(calving year-season, parity) were significant(p<0.05). The estimated lactation functions using Wood model for 2, 3, and 4 parity were yt=24.66t0.175e-0.00302t, yt=24.69t0.192e-0.00334t, and yt=24.22t0.200e-0.00341t, respectively. Phenotypic correlation (partial residual correlation) between calving interval and 305-d milk yield, A, b, c, persistency, peak day, and peak yield were 0.093, -0.014, 0.028, -0.046, 0.099, 0.085, and 0.052, respectively. To conclude, if calving interval increase then ascent to peak, persistency, peak day and peak yield are increase, and descent after peak is decrease. So, total 305-d milk yield is increase.

• Journal of the Korean Wood Science and Technology
• /
• v.18 no.1
• /
• pp.10-14
• /
• 1990

한국산 옻액의 경화거동을 알아보기 위하여 F.T.-I.R. 분석을 수행하였다. Acetone 추출한 urushiol의 F.T.-I.R. peak는 $3,422cm^{-1}$, $2,928cm^{-1}$, $1,622cm^{-1}$, $1,475cm^{-1}$, $1,281cm^{-1}$, $984cm^{-1}$, $947cm^{-1}$, $735cm^{-1}$이었다. 또한, 옻액의 정시경화거동에서 $1,651cm^{-1}$ peak는 urushiol-quinone이 laccase의 촉매작용에 의하여 산화중합한 후 982와 $947cm^{-1}$의 conjugated diene와 결합해서 dimer 형성을 알 수 있었다.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.3
• /
• pp.394-400
• /
• 2012

In this paper, charging modes of series resonant converter for a high voltage energy storage capacitor are compared in terms of charging time, peak resonant current, normalized peak resonant current and voltage in each operation mode. Operating principles of the full bridge series resonant converter with capacitor load are explained and analyzed in discontinuous and continuous operation mode. Based on the analysis and simulation result, $0.6{\omega}_r$ < ${\omega}_s$ < $0.75{\omega}_r$ and $1.3{\omega}_r$ < ${\omega}_s$ < $1.4{\omega}_r$ are evaluated to the best range of switching frequency for charging of an high voltage energy storage capacitor. 1.8 kJ/s SRC prototype is assembled with TI 28335 DSP controller and 40 kJ, 7 kV energy storage capacitor. Design rules based on the comparative analysis are verified by experiment.

• Journal of Korea Water Resources Association
• /
• v.41 no.7
• /
• pp.693-700
• /
• 2008

Detention pond has an important role in peak flow reduction to mitigate flood damage. Design of detention pond is accomplished through the preliminary stage, and design stage in general. New development projects produce increased peak flow and flow amounts. In this case it is necessary to design the detention pond easily and simply. A simplified design method of the detention pond is suggested in this study. Used design variables are peak flow ratio(${\alpha}$) and storage ratio($S_r$). ${\alpha}$ is the peak flow ratio of before and after development of the basin. $S_r$ is a ratio of storage volume to total runoff volume. Applicability of the proposed method was also proved. The simple procedure of detention pond design is proposed in this study.

• Fire Science and Engineering
• /
• v.16 no.4
• /
• pp.15-19
• /
• 2002

This dissertation is about the development of $BaTiO_3$-type PTC(Positive Temperature Coefficient) thermistor by composition method. A multilayer-type PTC samples were fabricated under optimal conditions after setting the experimental composition equation as ($Ba_{0.95-x}$S $r_{0.05}$$Ca_{x}$ )$TiO_3$-$0.01TiO_2$-$0.01SiO_2$-$\alpha$$MnCO_3$-$\beta$N $b_2$ $O_{5}$.) and their testing results were analyzed. The optimal sin-tering and cooling temperatures were 13$50^{\circ}C$ for two hours and $100^{\circ}C$/h for an hour, respectively; By composing Ca and Mn, dopants to lower the resistivity at room temperature, and Nb, a dopant to raise peak resistivity(Ca:5 mol%, Mn:0.08 mol%, Nb:0.18 mol%), appropriately, a PTC thermistor, having the characteristics of relatively low resistivity at room temperature and high peak resistivity and a good temperature coefficient, has been developed. And we find that it is possible of application for fire detection sensor.r.r.

• Journal of Biomedical Engineering Research
• /
• v.35 no.4
• /
• pp.87-94
• /
• 2014

Recent technological advances have increased interest in personal health monitoring. Electrocardiogram(ECG) monitoring is a basic healthcare activity and can provide decisive information regarding cardiovascular system status. In this study, we developed a capacitive ECG measurement system that can be included within a cloth mattress pad. The device permits ECG data to be obtained during sleep by using capacitive electrodes. However, it is difficult to detect R-wave peaks automatically because signals obtained from the system can include a high level of noise from various sources. Because R-peak detection is important in ECG applications, we developed an algorithm that can reduce noise and improve detection accuracy under noisy conditions. Algorithm reliability was evaluated by determining its sensitivity(Se), positive predictivity(+P), and error rate(Er) by using data from the MIT-BIH Polysomnographic Database and from our capacitive ECG system. The results showed that Se = 99.75%, +P = 99.77%, and Er = 0.47% for MIT-BIH Polysomnographic Database while Se = 96.47%, +P = 99.32%, and Er = 4.34% for our capacitive ECG system. Based on those results, we conclude that our R-peak detection method is capable of providing useful ECG information, even under noisy signal conditions.

• Smart Media Journal
• /
• v.8 no.3
• /
• pp.62-69
• /
• 2019

Electrocardiogram (ECG) signals cannot be counterfeited and can easily acquire signals from both wrists. In this paper, we propose a method of generating a coupling image using direction information of ECG signals as well as its usage in a personal recognition method. The proposed coupling image is generated by using forward ECG signal and rotated inverse ECG signal based on R-peak, and the generated coupling image shows a unique pattern and brightness. In addition, R-peak data is increased through the ECG signal calculation of the same beat, and it is thus possible to improve the recognition performance of the individual. The generated coupling image extracts characteristics of pattern and brightness by using the proposed convolutional neural network and reduces data size by using multiple pooling layers to improve network speed. The experiment uses public ECG data of 47 people and conducts comparative experiments using five networks with top 5 performance data among the public and the proposed networks. Experimental results show that the recognition performance of the proposed network is the highest with 99.28%, confirming potential of the personal recognition.