• Structural Engineering and Mechanics
• /
• 제52권3호
• /
• pp.559-572
• /
• 2014

This paper presents the results of an experimental investigation on the flexural behavior of doubly reinforced lightweight concrete (R.L.C.) beams tested under cyclic loading. A total of 20 beam specimens were tested. Test results are presented in terms of ductility index, the degradation of strength and stiffness, and energy dissipation. The flexural properties of R.L.C. beam were compared to those of normal concrete (R.C.) beams. Test results show that R.L.C. beam with low and medium concrete strength (20, 40MPa) performed displacement ductility similar to the R.C. beam. The ductility can be improved by enhancing the concrete strength or decreasing the tension reinforcement ratio. Using lightweight aggregate in concrete is advantageous to the dynamic stiffness of R.L.C. beam. Enhancement of concrete strength and increase of reinforcement ratio will lead to increase of the stiffness degradation of beam. The energy dissipation of R.L.C beam, similar to R.C. beam, increase with the increase of tension reinforcement ratio. The energy dissipation of unit load cycle for smaller tension reinforcement ratio is relatively less than that of beam with higher reinforcement ratio.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2001년도 봄 학술발표회 논문집
• /
• pp.138-145
• /
• 2001

This paper presents F.E.M. analysis result about the behavior of R.C. beam repaired with steel plate and fiber sheet. The effect of repairing varies with reinforcement ratio of R.C. beam, plate thickness, numbers of fiber sheet, and repairing length, etc. F.E.M. analysis using a program, DIANA, was carried out taking these factors as parameter in this study. Analysis result shows that repaired R.C. beam behaves differently according to parameters and certain cases imply that repairing is useless or may lay structure in dangerous condition. F.E.M. model considers that interfacial behavior between different two parts of repaired beam is rigid based on an assumption that adhesive failure does not appear before yielding of reinforcement and its analysis shows the result coincides with that of experiment.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 1998년도 학술발표회 발표논문집
• /
• pp.119-123
• /
• 1998

New design automation method of R/C beam based on the finite element method and the nonlinear truss model approach has been presented. The proposed method can substitute inaccurate existing method, which has limitation in its application, provide accurate and efficient design results for any type of R/C beam.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 봄 학술발표회 논문집
• /
• pp.597-602
• /
• 2001

Most of the predicted shear strength of continuous R.C. beam whitout web reinforcement were accepted by testing simple beams. But the experimental results may show that a differential behavior on simple and continuous R.C. beam. In this study, estimated shear strength of continuous R.C. beam without web reinforcement with internal force state factors by test as purpose to apply available predicted equation to normal continuous R.C. beam. This equation is applied to experimentally tested data and the results were compared with those predicted by the codes. Predicted shear strength using force state factor can provide a tested data rather than codes which like ACI

• Advances in materials Research
• /
• 제11권1호
• /
• pp.59-73
• /
• 2022

In the construction industry, thin-walled frame elements with very slender open cross-sections and low torsional stiffness are often subjected to a complex loading condition where axial, bending, shear and torsional stresses are present simultaneously. Hence, these often fail in instability even before the yield capacity is reached. One of the most common instability conditions associated with thin-walled structures is Lateral Torsional Buckling (LTB). In this study, a first order Generalized Beam Theory (GBT) formulation and numerical analysis of cold-formed steel lipped channel beams (C80×40×10×1, C90×40×10×1, C100×40×10×1, C80×40×10×1.6, C90×40×10×1.6 and C100×40×10×1.6) subjected to uniform moment is carried out to predict pure Lateral Torsional Buckling (LTB). These results are compared with the Finite Element Analysis of the beams modelled with shell elements using ABAQUS and analytical results based on Euler's buckling formula. The mode wise deformed shape and modal participation factors are obtained for comparison of the responses along with the effect of varying the length of the beam from 2.5 m to 10 m. The deformed shapes of the beam for different modes and GBTUL plots are analyzed for comparative conclusions.

• Steel and Composite Structures
• /
• 제3권5호
• /
• pp.333-348
• /
• 2003

The behaviour of composite frame - shear wall systems with regard to creep and shrinkage with high beam stiffness has been largely unattended until recently since no procedure has been available. Recently an accurate procedure, termed the Consistent Procedure (CP), has been developed which is applicable for low as well as for high beam stiffness. In this paper, CP is adapted for a class of composite frame - shear wall systems comprising of steel columns and R.C. shear walls. Studies are reported for the composite systems with high as well as low beam stiffness. It is shown that considerable load redistribution occurs between the R.C. shear wall and the steel columns and additional moments occur in beams. The magnitude of the load redistribution and the additional moment in the beams depend on the stiffness of the beams. It is also shown that the effect of creep and shrinkage are greater for the composite frame - shear wall system than for the equivalent R.C. frame - shear wall system.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1995년도 가을 학술발표회 논문집
• /
• pp.129-133
• /
• 1995

The purpose of this study is to evaluate the flexural bond performance in beam using 3-types anti-corrosion coatings. For the test. we used $15\times\times20\times110cm$ R.C beams, in which the epoxy, the red lead, and the cementitious anti-corrosion coating re-bars used. The results of test using these 3-type anti-corrosion coatings are shown that the flexural bond performance of cementitious anti-corrosion coating rebar in R.C beam is superior to other anti-corrosion coatings rebars.

• 콘크리트학회지
• /
• 제5권4호
• /
• pp.167-178
• /
• 1993

본 논문의 목적은 R.C.보 최적설계에 이산수학계획법을 적용하여 상세설계를 포함하는 실제설계의 가능성을 연구하기 위한 것이다. 이산최적문제에서 설계변수로는 단면의 총높이, 폭, 유효높이 및 길이방향철근의 단면적 그리고 전단철근의 단면적과 길이 방향철근의 절단점과 같은 상세변수 등이 고려되었다. 목적함수는 경비함수로 취했으며, 제약조건으로는 강도설계법에 의한 설계휨강도, 전단강도, 연성, 사용성, 콘크리트 덮개 및 철근간격, 복부보강 그리고 정착길이와 길이방향철근의 절단점 등에 관한 시방서 요구사항을 고려하여 문제를 형성하였다. 이산변수를 갖는 최적설계를 효율적으로 실행하기 위해 첫째단계에서 Feasible Direction Methed를 이용하여 연속최적해를 구했으며, 둘째단계에서 분기한계법(Branch and bound method)을 이용하여 이산최적해를 얻는 최적화 알고리즘을 제안하였다. 제안된 알고리즘의 신뢰도를 검증하기 위해 2개의 이산설계변수를 갖는 수치예에 적용하여 도해법 및 rounde-up method와 그 결과를 비교하였고, 단순지지된 R.C.보 및 2경간연속 R.C.보에 적용하여 제안된 알고리즘의 신뢰도, 효율성 및 적용성을 입증하였다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 봄 학술발표회 논문집
• /
• pp.555-560
• /
• 2003

Fatigue strength of concrete is ususlly presented by the Wohler Curve. But, new dimension T(time) from the view point of cyclic creep concept should be considerd. This paper presented four variable F-N-T-R relationship, this four variable relationship simultaneously accounts for the time effect and the effect of load rate. And analytical models are presented to predict fatigue strength of R/C beam strengthened with steel plate and carbon fiber sheet. Also, the correlation between the ratio of stress and the fatigue life was investigated.

• The Korean Journal of Ceramics
• /
• 제4권4호
• /
• pp.331-335
• /
• 1998

R-curve, of three kinds of silicon nitride-based ceramics were measured, using single edge notched beam (SENB) method at room and at elevated temperatures, up to $1200^{\circ}C$. Stable fraacture was seen on ceramic materials with SENB specimens if the machined notch is deep enough, even though the crack resistance did not increase with crack length. Hot pressed silicon nitride did not show the rising R-curve behavior at room temperature, but it showed some rising at $1000^{\circ}C$ and above. Si3N4 reinforced with SiC whiskers showed no rising behavior at room and elevated temperatures, as it has smaller grain size, compare to the monolithic specimen. Gas pressure sintered silicon nitride had very large and elongated grains, and it showed rising R-curve even at room temperature. However, it showed some creep behavior at $1200^{\circ}C$ and the calculated R-curve on this condition did not show a good result. We cannot apply this technique on this condition for obtaining the R-curve.