• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.8
• /
• pp.2051-2056
• /
• 2014

This paper investigated the separation of magnetic signal from a ferro-magnetic object. The magnetic signals were ILM(induced longitudinal magnetization) and IVM(induced vertical magnetization), which were induced by earth magnetic field and PLM(permanent longitudinal magnetization) and PVM(permanent vertical magnetization), which were due to a permanent magnetization of the object, respectively. Magnetic signal separation was based on the fact that magnetization vector could be analyzed according to longitudinal and vertical directions. Also the influence of non-uniform magnetic field from a rectangular coil on the separation was examined. A military vessel with a size close to rectangular coil has more errors on the magnetic signal separation.

• Journal of the Korea Society for Simulation
• /
• v.24 no.3
• /
• pp.45-54
• /
• 2015

This paper presents the influence of backlash can be greatly increased on the frequency response characteristic which is presented as the angular velocity of a motor to the motor input voltage, if the motor input voltage is adequately reduced. And, this paper verifies theoretically, analytically and experimentally the availability on the method of detecting the change of backlash magnitude by investigating on the change of the anti-resonance and resonance frequencies in the frequency response characteristic due to the change of backlash magnitude. The amount of change of anti-resonance frequency is more useful that of resonance frequency when detecting the change of backlash magnitude, because the change of anti-resonance frequency can be measured more stable. This paper also shows the sharp change of resonance frequency can be investigated when the motor input voltage is enough reduced. The work will be useful for the further research on the backlash estimation method of a servo system with a gear reducer.

• Korean Journal of Optics and Photonics
• /
• v.25 no.2
• /
• pp.78-84
• /
• 2014

In this paper secondary optics for an LED lamp with a narrow beam angle of $15^{\circ}$ were optimized by using a two-reflector system, to reduce both its size and the occurrence of satellite rings. The conic constant and the curvature of the primary reflector were determined by considering the relation of the source size to the beam angle, and the optimal position and radius of the secondary reflector were found for reducing the occurrence of satellite rings. Luminous flux efficiency was about 80%.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.21 no.5
• /
• pp.11-18
• /
• 2021

The small radio frequency tracking radar is a tracking system with a radio frequency sensor that identifies a target through all-weather radio frequency signal processing for a target and searches, detects and tracks the target for the major target. In this paper, we describe the development of a board equipped with TMS320C6678 and XILINX FPGA (Field Programmable Gate Array), a high-speed multi-core DSP that acquires target information through all-weather radio frequency and identifies a target through real-time signal processing. We propose DSP-FPGA combination architecture for DSP and FPGA selection and signal processing, and also explain the design of SRIO for high-speed data transmission.

• Journal of the Korea Society for Simulation
• /
• v.27 no.4
• /
• pp.69-77
• /
• 2018

Launching system is designed to store the payload, withstand the rigors, and prevent it from rusting and damaging. The behavior during initial deployment of the missile is determined by production, assembly and insertion condition of a launching tube and a missile. The purpose of this research is to confirm the safety of a launching tube by statistically analyzing behavior of the missile, during initial deployment stage. Error parameters which effect initial behavior of the missile are selected and analyzed through Monte-Carlo Simulation. Based on the result of simulation, tip-off and stress distribution between rail and shoe is predicted by using the commercial analysis program called Recurdyn. Lastly, the safety factor is calculated based on yield strength of the material and maximum stress of the rail during the process of launching. The safety of the launching system is verified from the result of the safety factors.

• Journal of the Korea Society for Simulation
• /
• v.28 no.2
• /
• pp.81-88
• /
• 2019

Since the AESA radar scans and tracks a distant targets or ground, it requires a test field which meets far-field condition before flight test. In order to test beam foaming, targeting, and availability from cluttering and jamming, it is general to build a outdoor roof-lab test site at tens of meters high. However, the site is affected by surrounding terrain, weather, and noise wave and is also requires time, space, and a lot of costs. In order to solve this problem, theoretical near-field beam foaming method has proposed. However, it requires modification of associated hardware in order to construct near-field test configuration. In this paper, we propose near-field beam foaming method which use single LUT in order to calibrate the variation of TRM(transmit-receive module) which consists AESA radar without modification of associated hardware and software. It requires less costs than far-field test and multiple LUT based near-field test, nevertheless it can derives similar experimental results.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.3
• /
• pp.141-147
• /
• 2019

In this paper, a beam pattern performance analysis was performed according to number of array elements and spacing of the phase array antenna. The distance between array elements in an array structure design was reduced due to the electrical length of Ka-band, which increases the number of array elements in applying the aperture. If the number of elements reduce by widening the array distance, the grating lobes of the same size as the main beam will occur in visible region. If the number of array elements should be applied to a system where the number of array elements should be minimized, the analysis was performed on a plan to reduce the number of array elements and minimize degradation of performance, such as beam width and side lobe level.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.21 no.6
• /
• pp.799-806
• /
• 2018

In this paper, we analyzed the communication distances in the flat and spherical earth model using the main specifications of the wireless communication device under development to be installed in the unmanned surface vehicle(USV). We installed the wireless communication device on the test ship and the actual communication test was performed in the South Sea of Korea, it compared the experimental result with the simulated results. If the installation altitude of the transmitting and receiving antennas is low, there is not the big difference between the two models. However, when the altitude of one of the two antennas is high, the spherical earth model has similar results to the experimental data. As the altitude of the antenna installation increases, fading occurs in a certain section. We expect that this fading can be overcome through antenna technologies such as space diversity.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.1
• /
• pp.197-202
• /
• 2019

A small millimeter-wave tracking radar power supply must provide stable power with minimal ripple noise and the switching frequency noise of the DC-DC converter must have a real-time self-test capability through on-the-fly monitoring without causing false alarms and ghost In this study, we developed a multi-output switching power supply with output power of more than 80% (@ 100% load) and 10 output power by adopting + 28VDC input for application to small millimeter wave tracking radar, DC-DC converter is applied for large power output and multi-output flyback method is applied for the remaining small power output. The test results show that 85% efficiency efficiency is achieved under 100% load condition.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.1
• /
• pp.9-14
• /
• 2019

A small millimeter-wave tracking radar is a pulse-based radar that searches, detects, and tracks a target in real time through a TWS (Track While Scan) method for a traps target on the sea with a large RCS running at low speed. It is necessary to develop a board equipped with a high-speed CPU to acquire and track target information through LPRF, DBS, and HRR signal processing techniques for a trap target operating various kinds of dexterous objects such as chaff and decoy, We designed a signal processor structure including DFT (Discrete Fourier Transform) module design that can perform real - time FFT operation using FPGA (Field Programmable Gate Array) and verified the signal processor implemented through performance test.