• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.1
• /
• pp.96-102
• /
• 1990

Cracks found in pressure vessels have been reported to be mostly semi-elliptic surface cracks. The fatigue crack growth behaviour of the surface cracks on pressure vessel materials, SPV 50Q and API 5A-K55, was studied with the consideration of the crack opening character. To determine the crack opening loads for the surface cracks, the displacement/strain were measured at three positions; the center and the side of the surface crack, the back face of the specimen using CMOD gauge and strain gauges. The experimental results showed that the crack opening load levels measured at the side of the surface crack were generally a little higher than those measured at the back face. As for the crack growth rates at the different parts of the surface crack, the experiments also showed that, if .DELTA.K$_{eff}$ is used, the exponent n of the Paris' law obtained were the same for the rear and the side parts of the surface cracks.

• Geophysics and Geophysical Exploration
• /
• v.9 no.1
• /
• pp.60-66
• /
• 2006

Three differing sandstones, two synthetic and one field sample, have been tested ultrasonically under a range of confining pressures and pore pressures representative of in-situ reservoir pressures. These sandstones include: a synthetic sandstone with calcite intergranular cement produced using the CSIRO Calcite In-situ Precipitation Process (CIPS); a synthetic sandstone with silica intergranular cement; and a core sample from the Otway Basin Waarre Formation, Boggy Creek 1 well, from the target lithology for a trial $CO_2$ pilot project. Initial testing was carried on the cores at "room-dried" conditions, with confining pressures up to 65 MPa in steps of 5 MPa. All cores were then flooded with $CO_2$, initially in the gas phase at 6 MPa, $22^{\circ}C$, then with liquid-phase $CO_2$ at a temperature of $22^{\circ}C$ and pressures from 7 MPa to 17 MPa in steps of 5 MPa. Confining pressures varied from 10 MPa to 65 MPa. Ultrasonic waveforms for both P- and S-waves were recorded at each effective pressure increment. Velocity versus effective pressure responses were calculated from the experimental data for both P- and S-waves. Attenuations $(1/Q_p)$ were calculated from the waveform data using spectral ratio methods. Theoretical calculations of velocity as a function of effective pressure for each sandstone were made using the $CO_2$ pressure-density and $CO_2$ bulk modulus-pressure phase diagrams and Gassmann effective medium theory. Flooding the cores with gaseous phase $CO_2$ produced negligible change in velocity-effective stress relationships compared to the dry state (air saturated). Flooding with liquid-phase $CO_2$ at various pore pressures lowered velocities by approximately 8% on average compared to the air-saturated state. Attenuations increased with liquid-phase $CO_2$ flooding compared to the air-saturated case. Experimental data agreed with the Gassmann calculations at high effective pressures. The "critical" effective pressure, at which agreement with theory occurred, varied with sandstone type. Discrepancies are thought to be due to differing micro-crack populations in the microstructure of each sandstone type. The agreement with theory at high effective pressures is significant and gives some confidence in predicting seismic behaviour under field conditions when $CO_2$ is injected.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.11a
• /
• pp.360-364
• /
• 2001

본 논문에서는 최근의 진화적 구조최적화(ESO) 전략을 회전축의 형상최적화에 적용하였으며, 각 계산 스텝마다 단위 유한요소의 크기를 변경함으로써 기존의 방법보다 빠르고 정확한 최적형상에 수렴하는 새로운 방법을 제시하였다. 축요소의 직경을 시스템 설계변수로 하였으며, 축중량의 감소, 공진배율(Q-factor)의 감소 및 충분한 위험속도의 분리여유를 갖도록 목적함수를 설정하였다. 불평형응답 및 굽힙응력의 구속조건을 부가하였으며, 목적함수에 대한 설계변수의 감도해석을 수행하였다. 전동기축계에 대한 적용 결과로부터 주파수와 동적 구속조건하의 로터베어링 시스템에 대한 축 형상 최적화에 ESO법이 효과적으로 이용될 수 있음을 확인하였다.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1767-1772
• /
• 2008

A microcantilever is a well-known MEMS structure for sensing bio-chemical molecules. When bio-chemical molecules are adsorbed on the microcantilever's surface, resonance frequency shift is generated. There are two issues in this phenomena. The first one is which one between mass change and surface stress change effects is more dominant on the resonance frequency shift. The second one is what will be the performance change when the boundary condition is changed from cantilevers to double clamped beams. We have studied the effect of surface stress change and compared it with that of mass change by using FEM analysis. Furthermore, for microstructures having different boundary conditions, we have studied Q-factor, which determines the detection limit of micro/nano mechanical sensors.

• 기술발표회
• /
• s.2006
• /
• pp.303-310
• /
• 2006

This study researched N-Value, strength of clayey soil and preconsolidation pressure m order to variety application of standard Penetration test. We compared it makes on analysis of the relationship of the N-value and $q_u$ with relation formula is presented in existing, presented the estimated preconsolidation pressure by using the predicted undrained shear strength.

• The Journal of Engineering Geology
• /
• v.30 no.4
• /
• pp.617-634
• /
• 2020

The purpose of this study is to investigate the relationship of between earthquakes and fluctuation of water level in a groundwater well of the active-fault zone and 124 national groundwater monitoring wells in Gyeongju area. The spatial and temporal relationships between the fluctuation of water level and the earthquake were analyzed by the calculation of earthquake effectiveness (ε) and q-factor which are the function of earthquake magnitude and distance from epicenter. Two earthquake events of E1 (April 22, 2019, M 3.8) and E2 (June 11, 2019, M 2.5) show a close relationship with a post-seismic 83 cm decrease and a pre-seismic 76 cm increase in water level at the active fault zone of Dangu-ri, respectively. The spatial analysis of water level fluctuation data in National Groundwater Monitoring Networks caused by earthquake events shows a more distinct response in deep groundwater around fault zones than other area, and a greater change in deep groundwater than shallow groundwater. It's inferred that the decrease and increase in groundwater level are affected by the expansion of fractures and compression of rock mass due to seismic stress, respectively. The effective ranges of ε-value and q-factor of the monitoring well in Dangu-ri were calculated as 2.70E-10~5.60E-10 and 14.4~18.0, respectively.

• Nuclear Engineering and Technology
• /
• v.21 no.2
• /
• pp.111-122
• /
• 1989

With the Zircaloy-4 tube oxidized in high temperature (1323 K) steam for 5, 10, 30 and 60 minutes, the expanding copper mandrel test was carried out over a temperature range of 673-l173k at $\varepsilon\;=\;3.0\times10^5S\;^1$. The oxidation parameters $(K_i)$ in the present study were linearly proportional to square root of time $(Ki= \delta_{kit})$ and their rate constants ($\delta_{ki}$) are 0.281, 2.82, and 2.313 for weight gain and thickness of Zr02 and $\alpha$(0) layer, respectively. Activation energy for high temperature (873-1073k) plastic deformation of Zircaloy-4 increases from 251 KJ/mol to 323 KJ/mol with increase in oxidation time from 5 minutes to 60 minutes due to the high strengthened Zr02. With the oxide layer thickness [K ; expressed in "Equivalent Cladding Reacted" (ECR,%)] and the yield stress obtained from the mandrel test, an empirical relation was derived as ($\sigma/C)^n=K^mexp$ (Q/RT) with n=6.9, m=5.7, C=0.155, 0.138, 0.051, and 0.046 MPa for Q=251, 258, 316, 323 KJ/mol, respectively.

• Journal of the Korean Geotechnical Society
• /
• v.25 no.6
• /
• pp.5-16
• /
• 2009

The is study is to evaluate the small strain shear modulus ($G_{max}$) of Busan clay using in-situ penetration tests. A series of dilatometer tests (DMT) and piezocone penetration tests (CPTu) are performed at Busan newport and Noksan sites, and hybrid oedometer tests are also carried out on the specimens obtained from both sites. The $G_{max}$ is evaluated from the shear wave velocity ($V_s$) measured by the bender elements installed at the boundary of oedometer cell. By analyzing these data, the relationship of $G_{max}$ and state variables, such as confined stress and void ratio, is developed. The analysis of lab and in-situ test results reveals that the ratio of $G_{max}$ to $q_t$ is inversely proportional to the plasticity index while the ratio of $G_{max}$ to $E_D$ has a linear relationship with ($I/I_D$)$(p_a/{\sigma}'_v)^{0.5}$. Two correlations suggested in this study, based on CPT and DMT results, appear to provide reasonable predictions of the small strain shear modulus.

• Journal of the Korean Geotechnical Society
• /
• v.22 no.4
• /
• pp.85-94
• /
• 2006

Triaxial tests at isotropic confining pressure of 200 kPa were carried out to show the undrained shear behavior of artificially cemented sands, which were cemented by gypsum, and the influences of relative density and DOC (degree of cementation) were investigated from the results. The yield strength, the elastic secant modulus at yield point and the peak frictional angle of cemented sands increased abruptly compared to uncemented sands, and it was checked that cementation exerts more influence on the behavior of sand than the relative density. But after breakage of the cementation bonds, the relative density was more important factor on the behavior of sand than the cementation. Because the compressibility md the excess pore pressure of cemented sands were reduced due to the cementation bonds, the effective stress path of cemented sands was going toward to the total stress path of uncemented sands. The cementation of sand restricted the dialtion of sand at the pre-yield condition, but induced more dilation in the post-yield condition.

• Journal of the Mineralogical Society of Korea
• /
• v.15 no.1
• /
• pp.44-58
• /
• 2002

A new polymorph of tridymite, an incommensurately modulated phase (IC phase), has been identified. While the symmetry of the IC lattice is same as that of the Ll phase, the geometry of the IC lattice structure is same as the basis of the L3 structure with a different modulation (modulation vector q=0.22 $c*_{H}$;$\lambda$ 37 ). On the other hand, the characteristic curved diffuse diffration observed from the Ll atoms could occur even at room phase suggests that the dynamic disordering of atoms, especially oxygen atoms could occur even at room temperature. The phase transition of Ll to L3 by grinding is gradual but very conspicuous: LllongrightarrowL1+IClongrightarrowIC+L3longrightarrowL3. However, it is revealed that real transition processes of individual grains are directly related to the local stress fields and preexisting microstructures.