• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.885-888
• /
• 2000

The effects of deposition temperature and post annealing process of ferroelectric PbZr$\sub$0.52/Ti$\sub$0.48/O$_3$(PZT) thin films by pulsed laser deposition (PLD) were investigated. The PZT thin films were deposited at 400, 450, 500, and 550$^{\circ}C$, with/without post annealing at 650$^{\circ}C$ for 30 min. The PZT thin films deposited above 500$^{\circ}C$ without post annealing were crystallized into peroveskite phase, but the PZT thin films deposited below 450$^{\circ}C$ had pyrochlore phase. The PZT thin films deposited below 450$^{\circ}C$ with post annealing also crystallized into pure perovskite. Compared to the PZT thin films which were deposited at 450$^{\circ}C$ and post annealed, the films deposited at 550$^{\circ}C$ have a columnar microstructure and high remnant polarization 28 (${\mu}$C/cm$^2$). With in-situ annealing at oxygen ambient, the PZT thin films reduced oxygen vacancies and increased retained polarization.

• Journal of the Korean Ceramic Society
• /
• v.37 no.5
• /
• pp.418-424
• /
• 2000

Effects of Ar ion damage prior to the phase transformation from pyrochlore to perovskite structure of PZT thin films have been investigated. As the degree of damage increased by increasing the acceleration voltage in the ion mass doping system, the phase transformation temperature decreased such that the temperature could be lowered down to 550$^{\circ}C$ when the film was damaged at 15 kV for 5 minutes. When the film was damaged prior to the heat treatment grain size of the perovskite thin films became less than 300${\AA}$. It turned out that relatively high value of the remanent polarization (about 30${\mu}$C/$\textrm{cm}^2$) as well as improvement of the fatigue characteristics to a large extent is closely related to the fine grain size of thus obtained PZT films.

• Journal of the Korean Ceramic Society
• /
• v.29 no.3
• /
• pp.216-222
• /
• 1992

PLZT thin films were prepared using sol-gel spin coating. The films mainly consisted of perovskite phase when heat treated at 600$^{\circ}C$ and in O2 or air atmosphere for 2 hours after 7 coating cycles. Cracks were formed when smaller than after 9 coating cycles. When ITO interlayer existed between Corning 7059 glass substrate and the film, cracks were not formed after 9 coating cycles, but cracks were formed after 11 coating cycles because of large volume change of the film contracting on the substrate during the heat treatment. In the observation of microstructure, the thin films have perovskite phase of about 2 $\mu\textrm{m}$ grain size and pyrochlore phase of 100∼200${\AA}$ grain size.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.4 no.4
• /
• pp.347-355
• /
• 1994

Thin films of $PbTiO_3$ were deposited on bare silicon wafers by the sol-gel process. Heat treatment of films was executed at temperature range from $400^{\circ}C$ to $750^{\circ}C$ to investigated its effect on the crystal structure and element distribution of $PbTiO_3$films. Only the perovskite structure was observed in the films annealed at $440^{\circ}C$ but pyrochlore structure was partially found at temperature range from $480^{\circ}C to 550^{\circ}C$. Thin films annealed at temperatures higher than $600^{\circ}C$ showed only the perovskite structure again but also showed the increasing loss of lead.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.5
• /
• pp.370-375
• /
• 2001

PZT thin films (3500${\AA}$) ahve been prepared onto Pt/Ti/corning glass (1737) substrates with a RF magnetron sputtering system using Pb$\sub$1.50/(Zr$\sub$0.52/,Ti$\sub$0.48)O$_3$ ceramic target. We used two-step annealing techniques, PZT thin films were grown at a 300$^{\circ}C$ substrate temperature and then subjected to an RTA treatment. In case of 500$^{\circ}C$ RTA temperature show pyrochlore phase. The formation of Perovskite phase started above 600$^{\circ}C$ and PZT thin films generated (101) preferred orientation. As the RTA time and temperature increased, crystallization of PZT films were enhanced. The PZT capacitors fabricated at 650$^{\circ}C$ for 10 minutes RTA treatment showed remanent polarization 30 ${\mu}$C/$\textrm{cm}^2$, saturation polarization 42${\mu}$C/$\textrm{cm}^2$, coercive field 110kV/cm, leakage current density 2.83x10$\^$-7/A/$\textrm{cm}^2$, remanent polarization were decreased by 30% after 10$\^$9/ cycles.

• Journal of the Korean Vacuum Society
• /
• v.10 no.4
• /
• pp.416-423
• /
• 2001

Microstructural, optical and dielectric properties of $SrTiO_3$ thin films were investigated. These films were deposited on the ITO glasses by rf-magnetron sputtering at room temperature and subequently heat treated in $O_2$ atmosphere at various temperatures. It has been found from X-ray diffraction patterns that as-deposited films prepared at room temperature are amorphous, while the films heat treated at temperature range of 400~$600^{\circ}C$ reveal the structure of pyrochlore. On the other hand, the structure of perovskite is dominantly observed in the films heat treated at temperatures over $650^{\circ}C$ in which the drastic changes of optical band gap and dielectric constant are observed. In addition, the phase transition peak is observed at $272^{\circ}C$ in the films heat treated at $600^{\circ}C$, while the dielectric dispersion is observed at near $310^{\circ}C$ in the films heat treated at $650^{\circ}C$.

• Transactions on Electrical and Electronic Materials
• /
• v.8 no.2
• /
• pp.84-88
• /
• 2007

[ $Bi_{1.5}Zn_{1.0}Nb_{1.5}O_7$ ] (BZN), $Bi_2Mg_{2/3}Nb_{4/3}O_7$ (BMN), and $Bi_2Cu_{2/3}Nb_{4/3}O_7$ (BCN) pyrochlore thin films were prepared on $Cu/Ti/SiO_2/Si$ substrates by pulsed laser deposition and the micro-structural and electrical properties were characterized for embedded capacitor applications. The BZN, BMN, and BCN films deposited at $25\;^{\circ}C$ and $150\;^{\circ}C$, respectively show smooth surface morphologies and dielectric constants of about $39\;{\sim}\;58$. The high dielectric loss of the films deposited at $150\;^{\circ}C$ compared with films deposited at $25\;^{\circ}C$ was attributed to the defects existing at interface between the films and copper electrode by an oxidation of copper bottom electrode. The leakage current densities and breakdown voltages in 200 nm thick-BMN and BZN films deposited at $150\;^{\circ}C$ are approximately $2.5\;{\times}\;10^{-8}\;A/cm^2$ at 3 V and above 10 V, respectively. Both BZN and BMN films are considered to be suitable materials for embedded capacitor applications.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.4 no.2
• /
• pp.199-209
• /
• 1994

$PbTiO_3$ thin films were prepared on soda-lime-silica slide glasses, Si-wafer and sapphire substrate by the dip-coating of precursor solution. As starting materials, titanium tetra iso-propoxide and lead acetate trihydrate were used. Then acetylacetone was added to prepare stable sol. The effect of the parameters such as viscosity and composition of sol were investigated. The optical transmittance at visible range, refractive index, IR spectra were measured in varying compositions, thickness and heat treatment temperature. The crystallization of $PbTiO_3$ films were measured by using XRD and SEM. Diffusion of compositions from slide glass to thin film were investigated by using EDX, too. These sols not precipitated for 20 days. Transmittance of $PbTiO_3$ films at visible range were decreased with the increase of thickness and heat treatment temperatures, and were exhibited flat spectra. Pyrochlore type appeared in the films on slide glass and perovskite type appeared in the films on Si-wafer or sapphire at $600^{\circ}C$. Perovskite crystals transformed to $PbTi_3O_7$ phase at $800^{\circ}C$.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.63 no.1
• /
• pp.46-49
• /
• 2014

$Pb(Zr_{0.52}Ti_{0.48})O_3(PZT)$ thin films deposited on $Ru/RuO_2$ bottom electrode that grown for in-situ progress used rf magnetron sputtering method. We investigated the dependence of the crystalline and electrical properties in the way of capacitors PZT thin films. Our results show that all PZT films indicated polycrystalline perovskite structure with preferred orientation (110) and no pyrochlore phase is observed. The electric properties of the Ru improved with increasing Ru thin films thickness. A well-fabricated Ru/PZT/Ru (100 nm) /$RuO_2$ capacitor showed a leakage current density in the order of $2.03{\times}10^{-7}$ $A/cm^2$ as a 50 kV/cm, a remnant polarization (Pr) of 9.22 ${\mu}C/cm^2$, and a coercive field (-EC) of -32.22 kV/cm. The results show that $Ru/Ru/RuO_2$ bottom electrodes are expected to reduce the degradation ferroelectric fatigue and excellent ferroelectric properties.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.49-52
• /
• 2003

The role of gas ratio with the crystallization behavior and electrical properties in $Bi_{3.25}La_{0.75}Ti_3O_{12}$(BLT) thin films by rf magnetron sputtering method has not been precisely defined. In this work, the ferroelectric properties of these films with gas variation was investigated. BLT thin films were deposited on the Pt/Ti bottom electrode by rf magnetron sputtering method and then they were crystallized by rapid thermal annealing (RTA). The experiment showed that all BLT films indicated perovskite polycrystalline structure with preferred orientation (020) and (0012). And no pyrochlore phase was observed. The fabricated film annealed with $O_2$ of 15 sccm showed that value of leakage current was $9.67{\times}10^{-7}A/cm^2$ at 50kV /em, and the value of remanent polarization (2Pr=Pr+-Pr-) was $11.8{\mu}C/cm^2$. Therefore we induce access to memory device application by rf-magnetron sputtering method in this report.