• Journal of Radiation Protection and Research
• /
• 제12권2호
• /
• pp.19-27
• /
• 1987

황산망간 용액조장치의 $^{56}Mn\;{\gamma}$선 검출효율을 결정하는데 $^{56}Mn$용액의 방사능을 절대측정하는 것은 필수적이다 $^{56}Mn$시료를 제작하기 위하여 99.99%의 순도를 갖는 Mn금속조각 13.718mg되는 시료를 한국에너지연구소 TRIGA MARK-II 원자로의 중성자선속이 약 $10^{13}n/cm^2{\cdot}s$되는 열중성자장에서 12분간 조사시켰다. 중성자 방사화된 $^{56}Mn$금속시료를 0.1N-HCI 용액 50ml 용해시켜서 $^{56}Mn$시료를 제작하여 $4{\pi}{\beta}-{\gamma}$ 동시계수기술로 방사능을 측정한 결과 불확도 0.366%를 갖는 값으로서 1987년 10월 15일 0 시를 기준하여 408.070kBq/mg을 얻었다.

• Progress in Superconductivity
• /
• 제7권2호
• /
• pp.145-151
• /
• 2006

Nickel and nickel-tungsten alloy were electroplated on a cold rolled and heat treated copper(Cu) substrate. 4 mm-thick high purity commercial grade Cu was rolled to various thicknesses of 50, 70, 100 and 150 micron. High reduction ratio of 30% was applied down to 150 micron. Rolled texture was converted into cube texture via high temperature heat treatment at $400-800^{\circ}C$. Grain size of Cu was about 50 micron which is much smaller compared to >300 micron for the Cu prepared using smaller reduction pass of 5%. 1.5 km-long 150 micron Cu was fabricated with a rolling speed of 33 m/min and texture of Cu was uniform along length. Abnormal grain growth and non-cube texture appeared for the specimen anneal above $900^{\circ}C$. 1-10 micron thick Ni and Ni-W film was electroplated onto an annealed cube-textured Cu or directly on a cold rolled Cu. Both specimens were annealed and the degree of texture was measured. For electroplating of Ni on annealed Cu, Ni layer duplicated the cube-texture of Cu substrate and the FWHM of in plane XRD measurement for annealed Cu layer and electroplated layer was $9.9^{\circ}\;and\;13.4^{\irc}$, respectively. But the FWHM of in plane XRD measurement of the specimen which electroplated Ni directly on cold rolled Cu was $8.6^{\circ}$, which is better texture than that of nickel electroplated on annealed Cu and it might be caused by the suppression of secondary recrystallization and abnormal grain growth of Cu at high temperature above $900^{\circ}C$ by electroplated nickel.

• 한국결정학회지
• /
• 제7권1호
• /
• pp.73-80
• /
• 1996

단일 온도대역 수평 Bridgman(1-T HB)법에 의해 2인치 직경의 GaAs 단결정을 성장시키기 위하여 그 장치를 설계·제작하였고, undoped, Si-doped 및 Zn-doped 단결정을 성장하였다. 단결정성의 측면에서 성장횟수별 비로 0.73의 단결정성을 보였고, 격자결함 밀도(etch pit density)는 n-type의 경우 평균 5,000/cm2, p-type의 경우 10,000/cm2, 그리고 undoped의 경우 20,000/cm2 정도를 보였다. 한편 undoped GaAs 단결정의 경우, Hall 측정에 의한 carrier 농도가 ∼1×1016/cm3인 것으로 나타나 기존의 이중 온도대역(2-T : double temperature zone) 또는 삼중 온도대역(3-T : three temperature zone) 수평 Bridgman 방식에 비하여 Si 유입량이 절반 수준인 것으로 측정되었다. 따라서 1-T HB 방식에 의하여 2-T나 3-T HB 방법보다 나은 수율을 갖고 더 순도가 높은 GaAs 단결정을 성장시킬 수 있었다.

• Carbon letters
• /
• 제10권1호
• /
• pp.9-13
• /
• 2009

We propose an evaluation method of the relative content of single-walled carbon nanotubes (SWCNT) in SWCNT soot synthesized by arc discharge using UV-VIS-NIR absorption spectroscopy. In this method, we consider the absorbance of semiconducting and metallic SWCNTs together to calculate the relative content of SWCNTs with respect to a highly purified reference. Our method provides the more reliable and realistic evaluation of SWCNT content with respect to the whole carbonaceous content than the previously reported method.

• 한국재료학회지
• /
• 제16권5호
• /
• pp.285-291
• /
• 2006

Copper powders have been widely used in electrically conductive coatings, electrode materials et al. and are very prospective since they are cheaper than noble metal powders such as silver or palladium. In this study, copper powders for metal filler of EMI shielding have been prepared using a solvothermal process from $CuSO_4$, NaOH, Glucose, mixed solvent ($H_2O$: Ethanol) and hydrazine which was used as a reducing agent at various reaction conditions. The prepared copper powders showed finely dispersed spherical shape without agglomerate, uniform morphology, narrow size distribution, high purity and were about 400-700 nm in size. The prepared powders were characterized using XRD, SEM, TGA, XPS, particle size measurement and EMI shielding efficiency.

• 마이크로전자및패키징학회지
• /
• 제23권4호
• /
• pp.63-67
• /
• 2016

Divalent europium-activated $Ca_2PO_4Cl$ phosphor powders were prepared by a chemical synthetic method followed by heat treatment in reduced atmosphere, and the crystal structures, morphologies and photoluminescence properties of the powders were investigated by x-ray powder diffraction, scanning electron microscope and spectrometer. The effect of Ca/P mole ratio at the starting materials on the final products was evaluated. The optimized synthesis condition obtained in this study was Ca/P mole ratio of 2.0. The present phosphor materials had higher photoluminescence intensity and better color purity than the commercial blue phosphor powders, $(Ca,Ba,Sr)_{10}(PO_4)_6Cl_2:Eu^{2+}$. The result of excitation spectrum measurement indicated that the excitation efficiency of the synthesized powders was higher for the long-wavelength UV region than that of the commercial phosphor. It was thus concluded that the samples prepared in this study can be successfully applied for the light-emitting devices such as LED excited with long-wavelength UV light sources.

• 한국표면공학회지
• /
• 제35권5호
• /
• pp.305-311
• /
• 2002

Optical measurements have been used to study the biaxial tensile strain in heteroeptaxial ZnTe epilayers on the (100) GaAs substrate by hot wall epitaxy (HWE) with Zn reservoir. It is effect on the low-temperature photoluminescence spectrum of the material. Optimum growth condition has been determined by a four-crystal rocking curve (FCRC) and a low temperature photoluminescence measurement (PL). It was found that Zn partial pressure from Zn reservoir has a strong influence on the quality of grown films. Under the determined optimum growth condition, ZnTe epitaxial films with thickness of 0.72~24.8$\mu\textrm{m}$ were grown for studying the effect of the thickness on crystalline quality. The PL and FCRC results indicated that the quality of ZnTe films becomes higher rapidly with increase of thickness up to 6$\mu\textrm{m}$. The best value of the FWHM of the four crystal rocking curve, 66 arcsec, was obtained on the film with 12$\mu\textrm{m}$ in thickness. The PL spectrum shows the splitted strong free exciton emissions and very weak deep band emissions. These results show the high quality of films.

• 한국연초학회지
• /
• 제22권1호
• /
• pp.91-98
• /
• 2000

This study was carried out to evaluate the uncertainty in the analysis of menthol content from the mentholated cigarette. Menthol in the sample cigarette was extracted with methanol containing an anethole as an internal standard, and then analyzed by gas chromatography. As the sources of uncertainty associated with the analysis of menthol, were the following points tested, such as the weighing of sample, the preparation of extracting solution, the pipetting of extracting solution into the sample, the preparation of standard solution, the precision of GC injections for standard & sample solution, the GC response factor of standard solution, the reproducibility of menthol analysis, and the determination of water content in tobacco, etc. For calculating the uncertainties, type A of uncertainty was evaluated by the statistical analysis of a series of observation, and type B by the information based on supplier's catalogue and/or certificated of calibration. Sources of uncertainty were subsequently included and mathematically combined with the uncertainty arising from the assessment of accuracy to provide the overall uncertainty. It was shown that the main source of uncertainty came from the errors in the reproducibility of menthol and water determination, the purity of menthol reference material in the preparation of standard solution, and the precision of GC injections for sample solution. The errors in sample weighing and volume measurement contributed relatively little to the overall uncertainty. The expanded uncertainty in the mentholated cigarettes, Korean and American brand, at 0.95 level of statistical confidence was $\pm$0.06 and $\pm$0.07 mg/g for a menthol content of 1.89 and 2.32 mg/g, respectively.

• 한국대기환경학회지
• /
• 제8권3호
• /
• pp.155-161
• /
• 1992

A simple, fast yet sensitive method is described for the determination of fifty elements in coal by inductively coupled plasma mass spectrometry. The method involves complete dissolution of coal with mixed acid $(HNO_3, HF, HClO_4)$ in hish pressure Teflon bomb and subsequent inductively coupled plasma mass spectrometric(ICP-MS) measurement. The accuracy of the method, being evaluated by the analysis of NIST SRMs (1632a, 1632b) is better than 20% RSD for most elements. The limits of detection defined by two times $\sigma$ (standard deviation of operational blank) are in order of sub-ppm to ppm, which are low enough to quantitate most elements. However, the determiantions for few elements such as V, As, Se are severely interfered by molecular ions such that their accurate determiantions are not possible. Analytical results for twentyon coals from eight countries including six ones world major coal producing, Korea, Japan, China, I.C.S., U.S.A., Canada, Australia, and South Africa are presented. While the results for major elements agree well with the existing ones, those for a few trace elements disagree considerably. The existing values are considerably higher. It is not possible to judge which are more accurate. However, the exisisting values are more likely to be errorous inasmuch as they are obtained without using high purity reagents and clean laboratory techniques.

• 한국세라믹학회지
• /
• 제38권10호
• /
• pp.867-870
• /
• 2001

지지촉매로 Ni-graphite를 사용하고 ${C_2}{H_2}$를 이용한 열화학기상증착법에 의하여 탄소나노소재를 합성하였다. 합성된 시편은 SEM, TEM, 라만 분광법으로 분석하였으며, 수소저장특성은 전기화학적인 방법에 의하여 평가하였다. 탄소나노소재 합성시 메카노케미컬 처리과정을 거친 시편이 거치지 않은 시편에 비하여 탄소나노튜브의 순도가 우수하였다. 한편, 탄소나노소재를 정제함에 따라 수소저장특성이 크게 향상되었다.