• Journal of the Mineralogical Society of Korea
• /
• v.26 no.4
• /
• pp.299-312
• /
• 2013

Magnetite, a major constituent mineral of the Hongcheon carbonatite-phoscorite complex, was produced over three stages in each rock type and decreased in quantity toward the late stage. Electron microprobe analyses for magnetite revealed that Ti and V were detected in traces, but showed increasing tendency from early to late stage. On the contrary, Mg and Mn decreased distinctly, and it is the general differentiation trend of carbonatitic magma. Al also showed decreasing tendency in carbonatite and phoscorite, and Cr was mostly below detection limit except late phoscorite. In early stage, $Fe^{2+}$ was largely replaced by $Mg{2+}$ and $Mn^{2+}$, and $Fe^{3+}$ by $Al^{3+}$ in magnetite, but it has nearly pure composition in late stage. Tendency of increase in V and decrease in Mn toward late stage represents that magma differentiation progressed under the condition of decreasing oxygen fugacity. Low concentrations of Mg, Al, Cr and Ti, as well as the absence of olivine and phlogopite, suggest that the Hongcheon carbonatite-phoscorite complex was generated from depleted magma. Especially, lower concentrations of Mg in magnetite compared to other typical carbonatite-phoscorite complex, and abundant occurrence of Fe-carbonate minerals and quartz in late stage, suggest that magma differentiation of the Hongcheon carbonatite-phoscorite proceeded to the latest stage.

• Korean Journal of Environmental Agriculture
• /
• v.36 no.1
• /
• pp.17-21
• /
• 2017

BACKGROUND: Castor oil and wormseed extract are important active ingredients for biopesticide, and ricinoleic acid in castor oil and three monoterpenes (ascaridole, carvacrol and p-cymene) in wormseed extract are known bioactive substances. However, their stabilities had not been studied, even though the stability was the core property for estimation of shelf-life of biopesticide. Aimed to investigate the thermal stabilities of the bioactive substances in castor oil and wormseed extracts. METHODS AND RESULTS: The contents of ricinoleic acid and three monoterpenes (ascaridole, carvacrol and p-cymene) were analyzed by gas chromatography (GC). The thermal stabilities of the bioactive substance were measured at $0^{\circ}C$, $23^{\circ}C$, $30^{\circ}C$, $40^{\circ}C$, $45^{\circ}C$ and $54^{\circ}C$ for 84 d. The half-lives of ricinoleic acid in biopesticides was ranged from 28.9 d to 57.8 d at $30^{\circ}C$, and the stability of pure castor oil were located in the range ($t_{1/2}$=46.2d for Indian product and 27.7 d for Korean product) at the same temperature. The half-lives of the total monoterpenes in biopesticides were ranged from 3.9 d to 27.7 d at $30^{\circ}C$. Among the monoterpenes, the stability ascaridole and p-cymene were decreased in acidic condition. All the bioactive substances showed similar stability on the different thermal conditions. CONCLUSION:The half-lives of most bioactive substance from castor oil and wormseed extracts were less than 100 d. To increase the stability of bioactive substance in biopesticide, stabilizing additives like antioxidant and oxygen remover should be considered to extend of the shelf-life.

• Korean Journal of Materials Research
• /
• v.30 no.8
• /
• pp.383-392
• /
• 2020

In this paper, AgCl/Ag₃PO₄/diatomite photocatalyst is successfully synthesized by microemulsion method and anion in situ substitution method. X-ray diffraction (XRD), photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), transmission electron microscopy (TEM), and ultraviolet-visible spectroscopy (UV-Vis) are used to study the structural and physicochemical characteristics of the AgCl/Ag₃PO₄/diatomite composite. Using rhodamine B (RhB) as a simulated pollutant, the photocatalytic activity and stability of the AgCl/Ag₃PO₄/diatomite composite under visible light are evaluated. In the AgCl/Ag₃PO₄/diatomite visible light system, RhB is nearly 100 % degraded within 15 minutes. And, after five cycles of operation, the photocatalytic activity of AgCl/Ag₃PO₄/diatomite remains at 95 % of the original level, much higher than that of pure Ag₃PO₄ (40 %). In addition, the mechanism of enhanced catalytic performance is discussed. The high photocatalytic performance of AgCl/Ag₃PO₄/diatomite composites can be attributed to the synergistic effect of Ag₃PO₄, diatomite and AgCl nanoparticles. Free radical trapping experiments are used to show that holes and oxygen are the main active species. This material can quickly react with dye molecules adsorbed on the surface of diatomite to degrade RhB dye to CO₂ and H₂O. Even more remarkably, AgCl/Ag₃PO₄/diatomite can maintain above 95 % photo-degradation activity after five cycles.

• Polymer(Korea)
• /
• v.32 no.1
• /
• pp.63-69
• /
• 2008

The mechanical properties and morphologies of cellulose blends with two different additives were compared. Poly (vinyl alcohol) (PVA) of ethylene glycol (EG) were used as additives in the formation of cellulose blends through the solution blending. The properties of blends were varied with the additive content in the polymer matrix. The ultimate tensile strength and initial modulus of the cellulose blends were highest for a blend PVA content of 30 wt% and for a blend EG content of 10 wt%, respectively. Ternary blended systems of composition of cellulose/PVA (70/30=w/w)/EG were also prepared by the solution blending method with different EG contents. The mechanical properties of these systems were found to be optimal for EG contents of up to 40 wt%. The mechanical properties of the cellulose ternary blend films were superior to those of the cellulose binary blend films. The oxygen permeability transmission rate ($O_2TR$) monotonically decreased with increasing EG content in the ternary blend films. Overall, the mechanical properties of the cellulose blend films were found to be better than those of pure cellulose films.

• The Journal of Korean Academy of Prosthodontics
• /
• v.39 no.1
• /
• pp.71-83
• /
• 2001

The purpose of this study was to compare the effects of various surface treatments by measuring removal torque on bone healing around titanium implants. 40 Screw-shaped cp titanium implants with length of 4mm, outer diameter of 3.75mm, and pitch-height of 0.5mm were used Group 1 was left as machined(control), Group 2 was blasted with $50{\mu}m\;Al_2O_3$, group 3 was blasted and etched in etching solution($NH_4OH : H_2O_2:H_2O= 1 : 1 : 5$) at $90^{\circ}C$ for 1 minute group 4 was blasted and oxidated under pure oxygen at $800^{\circ}C$. The implant surface roughness was analyzed with SEM and CLSM(Confocal Laser Scanning Microscope) and implants were placed in proximal tibial metaphysis of 10 New Zealand White rabbits. After 3 months of healing period, removal torque of each implant was measured to compare bone healing around implant. The results obtained were as follows 1. In SEM view, blasting increased the roughness of the surface, but etching of that rough surface decreased the roughness due to the removal of the tip of the peak. Oxidation also decreased the roughness due to formation of needle-like oxide grains on the implant surface. 2. The Sa value from CLSM was least in the machined group($0.47{\mu}m$), greatest in blasted group($1.25{\mu}m$), and the value decreased after etching($0.91{\mu}m$) and oxidation($0.94{\mu}m$). 3. The removal torque of etched group(24.5Ncm) was greater than that of machined group(16.7Ncm) (P<0.05), and was greatest in the oxidated group(40.3Ncm) and the blasted group(34.7Ncm).

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.7
• /
• pp.1448-1452
• /
• 2004

In this paper, a photodiode capable of obtaining a sufficient photo/ dark current ratio at both a forward bias state and a reverse bias state is proposed. The photodiode includes a glass substrate, an Cr thin film formed as a lower electrode over the glass substrate, Cr silicide thin film(∼l00$\AA$) ) formed as a schottky barrier over the Cr thin film, a hydrogenated amorphous silicon film formed as a photo conduction layer over a portion of the Cr silicide thin film. Transparent conduction film ITO (thickness 100nm) formed as an upper electrode over the hydro-generated amorphous silicon film is then deposited in pure argon at room temperature for the Schottky contact and light window. The high quality Cr silicide thin film using annealing of Cr and a-Si:H is formed and analyzed by experiment. We have obtained the film with a superior characteristics. The dark current of the ITO/a-Si:H Schottky at a reverse bias of -5V is ∼3$\times$IO-12 A/un2, and one of the lowest reported, hitherto. AES(Auger Electron Spectroscophy) measurements indicate that this notable improvement in device characteristics stems from reduced diffusion of oxygen, rather than indium, from the ITO into the a-Si:H layer, thus, preserving the integrity of the Schottky interface. The spectral response of the photodiode for wavelengths in the range from 400nm to 800nm shows the expected behavior whereby the photocurrent is governed by the absorption characteristics of a-Si:H.

• KSBB Journal
• /
• v.22 no.2
• /
• pp.91-96
• /
• 2007

The saccharogenic liquid (SFW) obtained by the enzymatic saccharification of food wastes was used as a medium for production of bacterial cellulose (BC). The enzymatic saccharification of food wastes was carried out by the cultivation supernatant of Tricoderma inhamatum KSJ1 culture. Acetobacter xylinum KJ1 was employed for the BC production culture. Under the scaled-up aeration condition of 1.0 vvm, 5.64 g/L of BC was produced in 3 days cultivation in 50 L air circulation bioreactor using SFW medium with addition of 0.4% agar. The productivity was similar to that of 10 L air circulation bioreactor (5.84 g/L). This cultivation method with 50 L air circulation bioreactor decreasing shear stress and increasing oxygen transfer coefficient ($k_La$) was very useful in BC mass production. The physical properties, such as morphology, molecular weight, crystallinity, and tensile strength of BC produced by the static culture (A), the air circulation culture using 10 L bioreactor (B) and 50 L bioreactor (C) were investigated. The number average molecular weight of BCs produced under the different culture conditions (A-C) showed 2,578,000, 1,975,000, and 1,809,000, respectively. Tensile strength was 1.72 $kg/mm^2$, 1.19 $kg/mm^2$, and 1.18 $kg/mm^2$, respectively. All of the BCs had a form of cellulose I representing pure cellulose. The relative degree of crystallinity showed the range of 86.2$\sim$87.8%. BC production by the air circulation culture mode brought more favorable results in terms of the physical properties and its ease of scale-up. Therefore, it is expected that the new BC production method, the air circulation culture using SFW, would contribute greatly to BC-related manufacturing.

• Journal of the Korean Chemical Society
• /
• v.31 no.6
• /
• pp.491-497
• /
• 1987

$ThO_2-Tm_2O_3$ (TDT) solid solutions containing 1,3,5,8,10, and 15 mol% $Tm_2O_3$ were synthesized from spectroscopically pure $ThO_2$ and $Tm_2O_3$ polycrystalline powders. The TDT solid solutions were indentified to the fluorite structure by the X-ray powder technique. The values of the lattice parameter were decreased with increasing amount of $Tm_2O_3$ incorporated. But, there was no linearity for the samples containing 8, 10, and 15 mol% $Tm_2O_3$. It was concluded that these samples became incomplete solid solutions. From the intensity analyses of X-ray diffraction patterns, the residual factor was found below 0.13 even for the 15 mol% TDT system. lt was confirmed from the DTA and TGA analyses that any phase transitions did not occur under the experimental condition executed. Comparing the pycnometric density with the lattice parameter obtained from XRD, it was suggested that the predominant defect model be an oxygen vacancy.

• Journal of the Korean Chemical Society
• /
• v.37 no.7
• /
• pp.635-641
• /
• 1993

Electrochemical cell, $Pt|air(PO_2=5.3{\times}10^{-3}atm)|Zr_{0.85}Ca_{0.15}O_{1.85}|air(PO_2= 0.21atm)|Pt$, has been designed to characterize the solid electrolyte and the temperature dependence of the electromotive force (EMF) has been measured in a temperature range of 600∼1000${\circ}$C. Solid electrolyte shows pure ionic conduction of the oxygen anion. The Fe-FexO, Co-CoO, Ni-NiO, and Cu2O-CuO electrodes have been prepared by mixing the 1 : 1 mole ratio of each metal and metal oxide and then by heating at 800${\circ}$C for 6 hours. Electrochemical cells, Pt│M(s), $MO(s)|Zr_{0.85}Ca_{0.15}O_{1.85}|air(PO_2=0.21atm)|Pt$, have been designed and the temperature dependence of the EMF has also been measured in the same temperature range. The changes of the thermodynamic state functions for the formation of the metal oxides are calculated from the electromotive forces and their temperature dependences. The material properties of the oxide systems are also discussed with the function changes.

• Korean Journal of Microbiology
• /
• v.45 no.4
• /
• pp.354-361
• /
• 2009

This study was carried out to develop an effective biocarrier-mediated bioaugmentation technology which will be useful for remediation of the crude oil-contaminated marine sediments. Enrichment of several microbial communities was made from several oil-polluted seashore sites and the two distinctively functional consortia have been successfully selected. These two consortia were grown together and used to manufacture the microbial agents for bioaugmentation of marine sediments polluted with crude oil. The most dominant species in the mixed culture was identified as Alcanivorax borkumensis based on pure culture and DGGE analysis. Bioaugmentation of oil-polluted marine sediments with the microbial agent MA-2 formulated using the mixed culture and biocarriers (activated carbon and minerals) was more effective, especially in combination with an oxygen producing (releasing) compound (ORC). Ninty percent of TPH was removed in the presence of ORC in 35 days while 74% in the absence of ORC. This indicated that the indigenous consortial degraders could be immobilized on the active carbon as a biocarrier to manufacture microbial agents and then effectively bioaugmented for remediation of the oil-polluted sediments.