• 한국세라믹학회지
• /
• 제51권5호
• /
• pp.447-452
• /
• 2014

This paper presents the effects of pulse plasma parameters such as duty cycle and pulse frequency on the properties of TiAlN coatings deposited by asymmetric bipolar pulsed DC magnetron sputtering systems. The results show that, with decreasing duty cycle and increasing pulse frequency, the coating morphology changes from a columnar structure to a dense structure with finer grains. Pulsed sputtered TiAlN coatings showed higher hardness, higher residual stress, and smaller grain sizes than did DC prepared TiAlN coatings. Moreover, residual stress and nanoindentation hardness of pulsed sputtered TiAlN coatings increased with increasing pulse frequency. Meanwhile, the surface roughness decreased continuously with increasing pulsed DC frequency up to 50 kHz.

• 한국결정성장학회지
• /
• 제14권4호
• /
• pp.145-150
• /
• 2004

We have investigated the structural, electrical and optical properties of Al-doped ZnO (AZO) thin films grown on glass substrate by pulsed DC magnetron sputtering as functions of pulse frequency and substrate temperature. A highly c-axis oriented AZO thin film is grown in perpendicular to the substrate when pulse frequency of 30 kHz and substrate temperature of $400^{\circ}C$ was applied. Under this optimized growth condition, the resistivity of AZO thin films exhibited $7.40\times 10^{-4}\Omega \textrm{cm}$. This indicated that the decrease of film resistivity resulted from the improvement of film crystallinity. The optical transmittance spectra of the films showed a very high transmittance of 85∼90 % in the visible wavelength region and exhibited the absorption edge of about 350 nm. The results show the potential application for transparent conductivity oxide (TCO) thin films.

• Transactions on Electrical and Electronic Materials
• /
• 제17권6호
• /
• pp.351-354
• /
• 2016

The mechanical properties of ITO films such as adhesion and internal stress are very important for the commercial application of solar cell devices. We report high quality pulsed DC magnetron sputtered ITO films deposited on silicon and glass substrates with low resistivity and high transmittance for various working pressures ranging from 0.96 to 3.0 mTorr. ITO films showed the lowest resistivity of $2.68{\times}10^{-4}{\Omega}{\cdot}cm$, high hall mobility of $46.89cm^2/V.s$, and high transmittance (>85%) for the ITO films deposited at a low working pressure of 0.99 mTorr. The ITO films deposited at a low working (0.96 mTorr) pressure had both amorphous and polycrystalline structures and were found to have compressive stress while the ITO films deposited at higher temperature than 0.99 mTorr was mixture of amorphous and polycrystalline and was found to have tensile stress.

• Journal of Magnetics
• /
• 제17권4호
• /
• pp.245-250
• /
• 2012

Ferromagnetic resonance and X-ray specular reflectivity measurements were performed on $Ni_{81}Fe_{19}/Ir_{20}Mn_{80}/Co_{90}Fe_{10}$ exchange bias trilayers, which were grown using the pulsed-DC magnetron sputtering technique on Si(100)/$SiO_2$(1000 nm) substrates, to investigate the evolution of the interface roughness and exchange bias and their dependence on the NiFe layer thickness. The interface roughness values of the samples decrease with increasing NiFe thickness. The in-plane ferromagnetic resonance measurements indicate that the exchange bias field and the peak-to-peak line widths of the resonance curves are inversely proportional to the NiFe thickness. Furthermore, both the exchange bias field and the interface roughness show almost the same dependence on the NiFe layer thickness. The out-of plane angular dependent measurements indicate that the exchange bias arises predominantly from a variation of exchange anisotropy due to changes in interfacial structure. The correlation between the exchange bias and the interface roughness is discussed.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2012년도 추계총회 및 학술대회 논문집
• /
• pp.179-180
• /
• 2012

Aluminum alloys are widely known as non-ferrous metal with light weight and high strength. Consequently, these materials take center stage in the aircraft and automobile industry. The Al7075 aluminum alloy is based on the Al-Zn-Mg-Cu and one of the strongest wrought aluminum alloys. Aluminum nitride has ten times higher thermal conductivity($319W/m{\cdot}K$) than Al2O3 and also has outstanding electric insulation($1{\times}1014{\Omega}{\cdot}cm$). Furthermore, it has high mechanical property (430 MPa) even though its co-efficient of thermal expansion is less than alumina For these reasons, it has great possibilities to be used for not only the field which needs high strength lightweight but also electronic material field because of its suitability to be applied to the insulator film of PCB or wafer of ceramic with high heat conduction. This paper investigates the mechanical properties and corrosion behavior of aluminum alloy Al7075 deposited with aluminum nitride thin films To improve the surface properties of Al7075 with respect to hardness, and resistance to corrosion, aluminum nitride thin films have been deposited by pulsed DC reactive magnetron sputtering. The pulsed DC power provides arc-free deposition of insulating films.

• Bulletin of the Korean Chemical Society
• /
• 제32권3호
• /
• pp.847-851
• /
• 2011

This study examined In-Zn-Sn-O (IZTO) films deposited on glass substrates by pulsed DC magnetron sputtering with various substrate temperatures. The structural, electrical, optical properties were analyzed. Xray diffraction showed that the IZTO films prepared at temperatures > $150^{\circ}C$ were crystalline which adversely affected the electrical properties. Amorphous IZTO films prepared at $100^{\circ}C$ showed the best properties, such as a low resistivity, high transmittance, figure of merit, and high work function of $4.07{\times}10^{-4}\;{\Omega}$, 85%, $10.57{\times}10^{-3}\;{\Omega}^{-1}$, and 5.37 eV, respectively. This suggests that amorphous IZTO films deposited at relatively low substrate temperatures ($100^{\circ}C$) are suitable for electrode applications, such as OLEDs as a substitute for conventional crystallized ITO films.

• 한국진공학회지
• /
• 제19권1호
• /
• pp.45-51
• /
• 2010

마그네트론 타겟에서 일어나는 다양한 물리적 현상에 의한 결과로 인해 발생하는 타겟 표면의 온도를 측정함으로써 그 분포가 플라즈마, 혹은 증착되는 박막에 영향을 줄 수 있는 가능성을 분석하였다. 마그네트론 스퍼터링의 타겟은 크게 원형 타겟과 사각 타겟으로 구분되는데, 사각 타겟에서는 자기장에 의한 corner effect 등에 의해 전자 집중 방전 영역이 발생하고 그것에 의해 타겟 표면에서 불균일한 온도분포가 생성됨을 확인했다. 국부적으로 온도가 높게 올라가는 지역은 비스퍼터링 지역에 비해 $10{\sim}20^{\circ}C$ 정도 높았으며, 스퍼터링 공정 시 문제점 중에 하나인 particle이 발생하면 그 부분에서 온도가 $20^{\circ}C$ 정도 더 상승함을 알 수 있었다. 이런 영향은 증착되는 박막의 균일도에도 적지 않은 영향을 주었으며 세라믹 타겟의 경우, 균열의 원인이 될 수 있고, 불균일한 타겟 침식으로 타겟의 수명을 단축시키는 문제를 유발하기도 한다.

• Transactions on Electrical and Electronic Materials
• /
• 제12권6호
• /
• pp.258-261
• /
• 2011

A ferroelectric $(Bi,La)_4Ti_3O_{12}$ (BLT) thin film fabricated by the pulsed-DC sputtering method was evaluated on a cell structure to check its compatibility to high density ferroelectric random access memory (FeRAM) devices. The BLT composition in the sputtering target was $Bi_{4.8}La_{1.0}Ti_{3.0}O_{12}$. Firstly, a BLT film was deposited on a buried Pt/$IrO_x$/Ir bottom electrode stack with W-plug connected to the transistor in a lower place. Then, the film was finally crystallized at $700^{\circ}C$ for 30 seconds in oxygen ambient. The annealed BLT layer was found to have randomly oriented and small ellipsoidal-shaped grains (long direction: ~100 nm, short direction: ~20 nm). The small and uniform-sized grains with random orientations were considered to be suitable for high density FeRAM devices.

• 한국표면공학회지
• /
• 제53권6호
• /
• pp.343-350
• /
• 2020

The degradation of mechanical properties of nitride coatings to steel substrates is one of the main challenges for industrial applications. In this study, plasma nitriding treatment was used in order to increase the mechanical properties of Mo-Cu-N coating to the H13 tool steel. The nanostructured Mo-Cu-N coating was deposited using pulsed DC magnetron sputtering method with a single alloy Mo-Cu target. Mechanical properties of MoN-Cu coated samples after nitriding were found to be relatively better than non-nitrided MoN-Cu coating.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제37회 하계학술대회 초록집
• /
• pp.406-406
• /
• 2009