• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.584-587
• /
• 1993

Mica, which have a good thermal and electrical characteristics, while will cleave easily at these layers. In order to bond mica materials soldily, mica/epoxy composite insulation materials were developed for generator stator winding. There are lots of problems such as delamination and partial discharge of these insulation materials caused by mechanical, electrical and thermal aging. Several experiments have been conducted in order to find the useful diagnostic parameters from the partial discharge phenomena by applying a new measurement techniques. this paper deals with the partial discharge pulse characteristics, which may be a useful diagnostic concept in predicting insulation condition of generator stator insulation materials. Long term insulation aging test shows that partial discharge phase angle an magnitude are identified as one of the main key techniques for insulation diagnosis on generator stator winding.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1455-1456
• /
• 2007

This paper presents the experimental results on impulse breakdown characteristics under a highly non-uniform electric field in $SF_{6}/N_{2}$ gas mixtures according to a change in temperature. Test temperature ranges from $-25^{\circ}C$ to $25^{\circ}C$. The impulse predischarge breakdown developments are investigated by the measurements of current pulse and discharge luminous events. As a result, the predischarge development mechanisms for both positive and negative polarities are same. When increasing the temperature, breakdown voltage due to lightning impulse voltage is increased in negative polarity. On the other hand, when increasing the temperature, breakdown voltage due to lightning impulse voltage is not changed in positive polarity.

• Tribology and Lubricants
• /
• v.16 no.5
• /
• pp.351-356
• /
• 2000

The feasibility of an ultrasonic technique using a pulse-echo method of normal-incident compressional waves was evaluated for its sensitivity to the worn surface and near surface damage due to wear. Worn surfaces were generated at various oscillation frequency under a given load and amplitude and these surface were in situ monitored using a ultrasonic wave detection system. Analysis of the ultrasonic waves received from the worn surface revealed a close relationship between the surface and near-surface damage and the maximum echo-amplitude of the compressional waves. The ultrasonic technique was successful in assessing the level of severity of the worn surface in real time during the wear process. It is also shown that the wear depth can be easily measured by the calculation of change of the specimen thickness based on the wave speed measured for the specimen medium.

• Journal of Physiology & Pathology in Korean Medicine
• /
• v.20 no.1
• /
• pp.131-137
• /
• 2006

This study was done to investigate the effect of Gamisamool-tang(GMSMT) on hypertension. After administering GMSMT extract to SHR for 5 weeks, changes in blood pressure, pulse rate, aldosterone and catecholamine levels in plasma were examined, and immunohistochemical changes were observed, and liver function test was done. The following results were obtained; blood presure decreased significantly as well as levels of aldosterone, norepinephrine and epinephrine in SHR, But levels of dopamine were unaffected. No capillary vessel dilation in adrenal cortex was observed. Safety against hepatic toxicity was showed. These results support a role for GMSMT might be usefully applied in treatment of hypertension.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.82.6-82
• /
• 2001

This paper presents the control X-Y table being the precise movement by point-to-point in the x-y plane. The dual modulus technique is used for our system to control the frequency of pulse supplied to the motors. Such technique is used to stop motor of both axes accurately as the desired target point in the same period. Both motors are stepping motor. To Improve steps per revolution, we employ ministep form to drive motors. In system, personal computer, using parallel port, is used for computing algorithm in open-loop form to control motors. In experiment, our system applies on the X-Y table for drawing to test system performance.

• Journal of the Korean Society for Railway
• /
• v.6 no.2
• /
• pp.81-86
• /
• 2003

This study proposes the neural network simulator for the integrity evaluation of weld zone in railway rails. For these purposes, the ultrasonic signals for defects(crack) of weld zone in frames are acquired in the type of time series data and echo strength. The detection of the natural defects in railway truck is performed using the characteristics of echodynamic pattern in ultrasonic signal. And then their applications evaluated feature extraction based on the time-frequency-attractor domain(peak to peak, rise time, rise slope, fall time, fall slope, pulse duration, power spectrum, and bandwidth) and attractor characteristics (fractal dimension and attractor quadrant) etc. The constructed neural network simulator agrees fairly well with the measured results of test block(defect location, beam propagation distance, echo strength, etc). The Proposed neural network simulator in this study can be used for the integrity evaluation of weld zone in railway rails.

• Journal of Power Electronics
• /
• v.19 no.5
• /
• pp.1153-1161
• /
• 2019

A current sharing controller is proposed in this paper for parallel-connected converters. The proposed controller is based on the calculation of the magnitudes of system current space vectors. Good current distribution between parallel converters is achieved with only one Proportional-Integral (PI) compensator. The proposed controller is analyzed and the circulating current impedance is derived for paralleled systems. The performance of the new control strategy is experimentally verified using two parallel connected converters employing Space Vector Pulse Width Modulation (SVPWM) feeding a passive RL load and a 2.2 kW three-phase induction motor load. The obtained test results show a reduction in the current imbalance ratio between the converters in the experimental setup from 53.9% to only 0.2% with the induction motor load.

• Journal of the Korean Society of Industry Convergence
• /
• v.22 no.3
• /
• pp.243-250
• /
• 2019

The nanosecond laser assisted ablation have been investigated. The biocompatable polymer PMMA was employed as the target material and the two distinctive surface conditions were test. The first surface condition is a dry surface for which the target surface is exposed to air and the second surface condition is the wet surface for which the target surface is covered with dehydrated water. The ablation volume, the laser induced acoustic wave, the laser induced plasma were investigated for both wet and dry condition. The nanosecond laser pulse ablatied more on the wet surface compared to the dry surface. The enhanced ablation of wet surface is attributed to the confined acoustic wave and the laser-induced plasma in the liquid layer.

• Proceedings of the KIPE Conference
• /
• 2019.07a
• /
• pp.279-280
• /
• 2019

본 논문에서는 3KW급 전력변환장치에 적용 가능한 650V급 GaN FET를 사용하여 Half-bridge 구조의 개발보드를 설계 및 제작하고, Double pulse test 실험을 통해 Turn-on 및 off 시스위칭 특성을 분석하였다. 또한 동기정류식 Buck 컨버터에 GaN FET을 적용하고, 유사한 전압 및 전류 정격의 Si MOSFET 소자와 시스템 효율을 비교하여 GaN FET 전력반도체의 성능을 평가하였다.

• Advances in concrete construction
• /
• v.13 no.1
• /
• pp.25-34
• /
• 2022

The production of geopolymer is considered as a cleaner process due to much lower CO₂ emission than that from the production of Portland cement. This paper presents a study of the potential use of recycled steel fibre (RSF) coming from the recycling process of the old tires in geopolymer mortars. Ground expanded perlite (EP) is used as a source of alumino-silicate and sodium hydroxide (NaOH=5, 10, 15, and 20M) is used as alkaline medium for geopolymer synthesis. RSFs were added to the mortar mixtures in four different volume fractions (0, 0.5, 1.0, and 1.5% of the total volume of mortar). The unit weight, ultrasound pulse velocity, flexural and compressive strength of expanded perlite based geopolymer mortar (EPGM) mixtures were determined. The microstructures of selected EPGMs were examined by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) analyses. The optimum molarity of sodium hydroxide solution was found to be 15M for geopolymer synthesis by EP. The test results revealed that RSFs can be successfully used for fibre-reinforced geopolymer production.