• Journal of the Korean Magnetics Society
• /
• v.13 no.4
• /
• pp.182-186
• /
• 2003

A new axial pressing method using pulse magnetizing field was studied to improve the remanence of Nd-Fe-B sintered magnets. In order to make near-net shape green compacts of butterfly, disk, or coin magnets, conventional axial-type pressing has been normally used. However, compared to the transverse-type pressing, it is not possible to obtain higher remanence by this method because the magnetic alignment of powder begins to deteriorate when the density of green compacts increases over a critical value. On the other hand, we found that an axial pressing under pulse magnetizing field was very effective to increase the degree of magnetic alignment of powder, yielding remanences even higher than those obtained by the transverse pressing. In this study, it was revealed that appropriate tapping density and how to apply pulse magnetic held were important to improve the grain alignment and thus remanence of Nd-Fe-B sintered magnet.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.5 no.4
• /
• pp.64-70
• /
• 1994

the magnetic field homogeneities of the induction coils of various sizes and shapes were investigated in order to prepare for the magnetic field immunity test under the power frequency, the pulse and the damed oscillatory fields recommended by the IEC. For this purpose, we analyzed the magnetic field homogeneities in the two induction coils with $1m\times1m$, and $1m\times2.6m$, , and the double square coils with 0.8m and 0.6m spaced. The testing volume within $\pm$3dB in the double square coil with 0.8m spaced in twice bigger than single square coil with 1m side in the z-direction.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.8
• /
• pp.654-659
• /
• 2008

This paper is to suggest a concept design of the permanent magnet type magnetic resonance imaging (MRI) device based on the parameter optimization method. Pulse currents in the gradient coils will introduce the effect of eddy currents in the ferromagnetic material, which will worsen the quality of imaging. In order to equalize the magnetic flux in the MRI device for good imaging, the eddy current effect in the ferromagnetic material must be taken into account. This study attempts to use the design of experiment (DOE) and the response surface method (RSM) for equalizing the magnetic flux of the permanent magnet type MRI device using that the magnetic flux can be calculated directly using a commercial finite element analysis package. As a result, optimal shapes of the pole and the yoke of the PM type MRI device can be obtained. The commercial package, ANSYS, is used for analyzing the magnetic field problem and obtaining the resultant magnetic flux.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2013.12a
• /
• pp.155-156
• /
• 2013

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.6
• /
• pp.981-987
• /
• 2017

In this paper, we describe the LPM structure with a two-phase, which is not used previously, and explain its operation principle. In order to predict the accurate performance of LPM reduction model, finite element model was derived and the back EMF of LPM reduction model was measured and compared. In order to investigate the thrust and normal force of the LPM reduction model, a driving circuit capable of applying two-phase pulse currents was constructed and the performance was predicted in conjunction with the finite element analysis model. Finally, the design considering actual LPM size was performed. Since the size of the reduction model is small, the field could be made of a permanent magnet. However, it is almost impossible to manufacture a permanent magnet to match the size and capacity of a real LPM for a vehicle, in terms of cost and writing. Therefore, the actual vehicle LPM was replaced by wound type that generates a magnetic field by applying current to the field winding, and the final model was derived using the reaction surface method.

• Journal of Magnetics
• /
• v.21 no.2
• /
• pp.281-285
• /
• 2016

The purpose of study was to evaluate SNR and CNR with different contrast agent contents (1.0 mmol/mL gadobutrol and 0.5 mmol/mL gadoterate meglumine) for spin echo (SE) and 3-dimension contrast-enhanced fast field echo (3D CE-FFE) pulse sequences. In this study, we compared the SNR and the CNR between 0.5 mmol/mL gadoterate meglumine and 1.0 mmol/mL gadobutrol according to the concentration of contrast agent in brain MRI. When we compared between SE and 3D CE-FFE pulse sequences, the higher SNR and CNR using 3D CE-FFE pulse sequence can be acquire regardless of contrast agent contents. Also, a statistically significant difference was found for SNR and CNR between all protocols. In conclusion, our results demonstrated that the SNR and CNR have not risen proportionately with contrast agent contents. We hope that these results presented in this paper will contribute to decide contrast agent contents for brain MRI.

• Journal of Astronomy and Space Sciences
• /
• v.30 no.2
• /
• pp.91-94
• /
• 2013

We use the outer gap model to explain the spectrum and the energy dependent light curves of the X-ray and soft ${\gamma}$-ray radiations of the spin-down powered pulsar PSR B1509-58. In the outer gap model, most pairs inside the gap are created around the null charge surface and the gap's electric field separates the opposite charges to move in opposite directions. Consequently, the region from the null charge surface to the light cylinder is dominated by the outflow current and that from the null charge surface to the star is dominated by the inflow current. We suggest that the viewing angle of PSR B1509-58 only receives the inflow radiation. The incoming curvature photons are converted to pairs by the strong magnetic field of the star. The X-rays and soft ${\gamma}$-rays of PSR B1509-58 result from the synchrotron radiation of these pairs. The magnetic pair creation requires a large pitch angle, which makes the pulse profile of the synchrotron radiation distinct from that of the curvature radiation. We carefully trace the pulse profiles of the synchrotron radiation with different pitch angles. We find that the differences between the light curves of different energy bands are due to the different pitch angles of the secondary pairs, and the second peak appearing at E > 10 MeV comes from the region near the star, where the stronger magnetic field allows the pair creation to happen with a smaller pitch angle.

• Proceedings of the KIEE Conference
• /
• 1990.11a
• /
• pp.32-36
• /
• 1990

LPM is a characterized motor to reciprocate linear motion for the office automation(OA), the factory automation(FA) and the field of information instruments because it can generate direct drive without any mechanical converter. For the design and analysis of permanent magnet type linear, pulse motor, it is therefore necessary to investigate the characteristics of magnetic flux distribution, static and dynamic thrust force, normal force, etc, by analyzing its magnetic circuit. This paper describes various useful methods for improving the characteristics of LPM. And these method is adopted on the PM and flat type, double side 2-phase 8-pole LPM.

• Journal of the Optical Society of Korea
• /
• v.12 no.1
• /
• pp.57-61
• /
• 2008

We investigated the laser pulse-width dependence of dense plasmas confined within the magnetic length of $In_{0.2}Ga_{0.8}As$/GaAs multiple quantum wells under high magnetic fields up to 31 T. To fully fill the Landau levels of effectively zero-dimensional system, we used intense femtosecond (fs) laser pulses to create carrier densities near $10^{13}/cm^2$. The observed photoluminescence showed a characteristic of superfluorescence, above critical magnetic field when being excited by pulses shorter than coherence buildup time.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.12
• /
• pp.2135-2144
• /
• 2007

This paper presents system design of the slotless double-side Permanent Magnet Linear Synchronous Machine system (PMLSM) through magnetic field analysis and dynamic modeling. In our analysis, 2-D analytical treatments based on the magnetic vector potential were adopted to predict magnetic field with space harmonics by PM mover magnetization and stator winding current. From these, the design parameters such as inductance, Back-emf, and thrust are estimated. And, the electrical dynamic modeling including synchronous speed is completed by calculation of a DC link voltage in effort to obtain the accurate mechanical power from Space Vector Pulse Width Modulation(SVPWM). Therefore, the system design of PMLSM is performed from estimation of design parameters according to PM size and coil turns in magnetic field and from calculation of a DC link voltage to satisfy base speed and base thrust represented as the maximum output power in dynamic modeling. The estimated values from the analysis are verified by the finite element method and experimental results.