• 한국정밀공학회지
• /
• 제21권12호
• /
• pp.13-20
• /
• 2004

Manufacturing process for the microfluidic device can include such sequential steps as master fabrication, electroforming, and injection molding. The laser ablation using masks has been applied to the fabrication of channels in microfluidic devices. In this study, manufacturing of polymer master and mold insert for micro injection molding was investigated. Ablation of PET (polyethylene terephthalate) by the excimer laser radiation could be used successfully to make three dimensional master fur nickel mold insert. The mechanism fur ablative decomposition of PET with KrF excimer laser $({\lambda}: 248 nm, pulse duration: 5 ns)$ was explained by photochemical process, while ablation mechanism of PMMA (polymethyl methacrylate) is dominated by photothermal process, the .eaction between PC (polycarbonate) and KrF excimer laser beam generate too much su.face debris. Thus, PET was adopted in polymer master for nickel mold insert. Nickel electroforming using laser ablated PET master was preferable for replication method. Finally, it was shown that excimer laser ablation can substitute for X-ray lithography of LIGA process in microstructuring.

• Journal of Power Electronics
• /
• 제13권5호
• /
• pp.806-813
• /
• 2013

This paper aims to compare the performance of three phase induction motor drives using Five Leg Inverter (FLI) and Three Leg Inverter (TLI) configurations. An Indirect Field Oriented Control (IFOC) method using a TLI is well established and incorporated for high performance speed drives in various industries. The FLI dual motor drive system on the other hand shows good workability in the independent control of two induction motor drives simultaneously. In this experiment, the IFOC method is utilized for both drive systems, and Space Vector Pulse Width Modulation (SVPWM) is used to generate pulses for both inverters. For the FLI, the Double Zero Sequence (DZS) Injection technique is used to generate the modulation signal. The complete experiment setup is done by using a DSpace 1103 controller board. The individual motor performances are analyzed using similar schemes, equipment setups and controller parameter values. The results show similar speed performance response capability between the single motor operation using a TLI system and the two motor operation using a FLI system based on the variable speed range either in forward or reverse operation. They also show similar load rejection abilities. However, the single motor with a TLI has a better power quality aspect such as ripple current and total harmonics distortion (THD).

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제8권1호
• /
• pp.11-20
• /
• 2008

The structure of 2-bit/cell flash memory device was characterized for sub-50 nm non-volatile memory (NVM) technology. The memory cell has spacer-type storage nodes on both sidewalls in a recessed channel region, and is erased (or programmed) by using band-to-band tunneling hot-hole injection (or channel hot-electron injection). It was shown that counter channel doping near the bottom of the recessed channel is very important and can improve the $V_{th}$ margin for 2-bit/cell operation by ${\sim}2.5$ times. By controlling doping profiles of the channel doping and the counter channel doping in the recessed channel region, we could obtain the $V_{th}$ margin more than ${\sim}1.5V$. For a bit-programmed cell, reasonable bit-erasing characteristics were shown with the bias and stress pulse time condition for 2-bit/cell operation. The length effect of the spacer-type storage node is also characterized. Device which has the charge storage length of 40 nm shown better ${\Delta}V_{th}$ and $V_{th}$ margin for 2-bit/cell than those of the device with the length of 84 nm at a fixed recess depth of 100 nm. It was shown that peak of trapped charge density was observed near ${\sim}10nm$ below the source/drain junction.

• 한국광학회지
• /
• 제5권1호
• /
• pp.84-89
• /
• 1994

연속발진 색소레이저를 시드레이저로 하고, Nd:YAG 레이저로 펌핑하는 인젝션 록킹된 단일 모우드 펄스 색소레이저를 제작하였다. 위상민감 검출법으로 얻은 오차신호로 시드빔과 공진 상태를 유지하도록 공진기 길이를 조절하였을 때 99% 이상의 펄스가 시드레이저의 주파수에 록킹 되었다. 이때 레이저 출력빔의 중심 주파수 요동이 10MHz 이내로 안정되었다. 펄스폭(FWHM)은 6ns이고 선폭은 130 MHz이었다. 50mJ로 펌핑하였을 때 2mJ의 출력을 얻었으며 이때의 첨두출력은 0.33 MW이다.

• 한국자동차공학회논문집
• /
• 제13권5호
• /
• pp.64-74
• /
• 2005

The effect of fuel injection spray on engine performance has been known as one of the major concerns for improving fuel economy and reducing emissions. In general, reducing the spray droplet size could prevent HC emission in gasoline engine. As far as PFI gasoline engine is concerned, the mixture of air and fuel may not be uniform under a certain condition, because breakup and production of spray droplets are made in a short distance between the fuel injector and intake valve. This study, by constituting PFI gasoline spray system, was performed to study the transient spray characteristics and dynamic behavior of droplets from two-holes two-sprays type injector used in DOHC gasoline engine. Mean droplet size and optical concentration in accordance with various conditions were measured by LDPA and CCD camera. Through this study, the variation of drop size and optical concentration could be used for understanding the behavior of unsteady spray was declared and the existing the small droplets between each pulse spray could be estimated caused to the development of wall film was conformed.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.267-268
• /
• 2008

This paper presents compact low frequency ultra-wide band(UWB) sensor design and studying of the partial discharge diagnosis by sensing electromagnetic pulse emitted from the partial discharge source with new designed UWB sensor. In this study, we designed new type of compact low frequency UWB sensor based on microstrip antenna technology to detect both low frequency and high frequency band of partial discharge signal. And experiments of offline PD testing on in medium voltage (22.9kV) underground cable and mention the comparative results with the traditional HFCT as a reference sensor in the laboratory. In the series of comparative test, the calibration signal injection test provided with conventional IEC 60270 method and high voltage injection testing are included.

• 대한전자공학회논문지
• /
• 제18권2호
• /
• pp.27-35
• /
• 1981

본 연구에서는 비정질 갈코게나이트박막의 스위칭과도 특성을 분석하기 위해 공체전하중를 모델에 의한 수식적 이론과 그 이론의 타부성에 따른 실험을 연하였다. 이론과 실험에 대한 분석적인 관찰을 실온에서 비정용 잘코게나이드박막에 전압펄스를 인가할 때 생기는 스위칭과도 특성에 대해 비교하였다. 결과로는 전자스위칭 특성에 대한 단순한 이론적 모델의 형태로 설명할 수 있다. 캐리어의 주입은 스위칭 특성을 유발시키기에 필요하며 주입된 캐리어들은 공간전하제한전류(SCLC)로서 전류 흐름에 기여한다. 그러므로 제안된 전하제어 스위칭 특성은 2중 주입 공간 전하중첩 모델로 해석할 수 있다.

• 한국추진공학회지
• /
• 제19권3호
• /
• pp.1-8
• /
• 2015

70 N급 단일액체추진제 추력기 개발모델의 연소실 압력진동 강도와 추력응답특성이 갖는 상관도 도출을 위해 지상연소시험을 수행하였다. 단일추진제급 하이드라진이 연소시험용 추진제로 선정되었고, 연소실의 특성길이와 추진제 분사압력이 시험변수로 적용되었다. 시험조건 내에서의 추력실 직경 및 추진제 분사압력의 감소는 정체실의 압력진동을 증대시키고, 압력진동은 시험모델의 펄스 응답성능을 저해하는 요소로 작용하는 것이 확인되었다.

• 한국추진공학회지
• /
• 제15권3호
• /
• pp.22-30
• /
• 2011

추력변화를 위한 방법에는 여러 가지가 있는데, 고압력 강하 시스템, 이중 매니폴드 분사기, 가스 분사, 다중 챔버, 펄스 추력, 움직이는 분사기 구성요소 등이 있다. 이 중에서 이중 매니폴드 분사기의 경우에는 하나의 분사기 구조에 서로 다른 두 개의 매니폴드를 가지는 분사기를 결합하는 방식의 분사기인데, 각 분사기는 각각의 연료 공급시스템을 독립적으로 가지고 있어 각 매니폴드마다 독립적으로 유량을 조절 할 수 있다. 본 논문에서는 이중 매니폴드 분사기를 사용하여 넓은 추력범위에서 연료분사의 안정성을 판단하기 위하여 각 매니폴드의 접선방향 유입구 넓이의 비와 분사압력에 따라 분사 형상을 측정하고, 분사기 오리피스 끝단에서 액막 두께를 측정하였다.

• 반도체디스플레이기술학회지
• /
• 제20권3호
• /
• pp.22-26
• /
• 2021

Thin-film encapsulation (TFE) technology is most effective in preventing water vapor and oxygen permeation in the organic light emitting diodes (OLED). Of those, a laminated structure of Al₂O₃ and MgO were applied to provide efficient barrier performance for increasing the stability of devices in air. Atomic layer deposition (ALD) method is known as the most promising technology for making the laminated Al₂O₃/MgO and is used to realize a thin film encapsulation technology in organic light-emitting diodes. Atomic layer deposited inorganic films have superior barrier performance and have advantages of excellent uniformity over large scales at relatively low deposition temperatures. In this study, the control system of the MgCP₂ precursor for the atomic layer deposition of MgO was established in order to deposit the MgO layer stably by the injection time of second level and the stable heating temperature. The deposition rate was obtained stably to be from 4 to 10 Å/cycle using the injection pulse times ranging from 3 to 12 sec and a substrate temperature ranging from 80 to 150 ℃.