• 마이크로전자및패키징학회지
• /
• 제10권4호
• /
• pp.73-79
• /
• 2003

Sn-Ag 전해도금시 도금욕의 Ag 이온의 농도, 전류밀도, 펄스 주기, 첨가제등의 인자들이 솔더의 조성과 표면형상에 미치는 영향에 관하여 연구하였다. Ag 이온의 농도와 시편에 가해지는 전류밀도를 변화시킴으로써 Sn-Ag 솔더내의 Ag 조성을 조절하는 것이 가능하였고 또한 전류밀도를 증가시키면 솔더의 미세조직의 크기가 감소되는것을 관찰하였다. 펄스 인가 주기와 첨가제의 양등을 변화시키면 솔더내 Ag의 조성이 달라지고 솔더의 표면 거칠기가 감소하면서 표면 형상이 변화됨을 확인하였다. 이러한 과정을 통하여 30 $\mu\textrm{m}$의 미세피치와 15$\mu\textrm{m}$의 범프 높이를 가지는 공정 Sn-Ag 솔더 범프를 형성하였다. 도금된 솔더의 조성은 EDS와 WDS 분석을 통하여 확인하였고 표면형상은 SEM과 3D surface analyzer를 사용하여 분석하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권3호
• /
• pp.430-436
• /
• 2008

Recently, there are many cases to use a ship's engine performance analyzer(SEPA) to measure pressure in cylinder and top dead center(TDC) of piston of engine, and analyze its performance such as fuel injection time and horsepower as well as wear of piston ring. But, SEPA needs TDC pulses($T(1){\sim}T(n)$) generated when pistons of engine are located to the TDC position ($TDC(1){\sim}TDC(n)$), these pulses are gathered from sensors connected to gear wheel of the propeller shaft in the remote distance from the measurement point. Therefore, operators need a long wire cable(WRC) to TDC detecting sensor to get these pulses, but this method is a very uncomfortable and expensive in case of installation, and it might decrease user's purchase desire. In this paper, we design and fabricate a small and inexpensive MODEM cable(M0C) so that it may be available to transmit TDC pulse generated from sensor in propeller shaft through existing power line. We also verify the facts that this MOC can be applied to SEPA and the effectiveness of the system through the experiments.

• 한국전자파학회논문지
• /
• 제24권6호
• /
• pp.661-670
• /
• 2013

본 논문에서는 고정 주파수 신호와 선형 주파수 변조 신호가 혼합된 연속 위상을 갖는 주기성 혼합 파형에 대한 선형 주파수 변조 파형의 측정 기법을 제시한다. 다양한 신호 파형을 생성하는 주파수 합성기와 송신 신호를 고출력으로 증폭하는 고출력 증폭기로 구성된 소형 레이더 송신기는 연속 위상을 갖는 혼합 파형을 생성한 다. 첫 번째로 위상이 연속적인 신호를 갖는 소형 레이더 송신기의 구성을 요약하고, 선형 주파수 변조 파형의 비정합에 의한 펄스 압축의 왜곡 특성을 고찰한다. 두 번째로 연속 위상을 갖는 혼합 파형에서 선형 주파수 변조 파형을 측정하기 위해 스펙트럼 분석기를 사용한 측정 기법, 신호원 분석기를 사용한 측정 기법 및 RF 혼합기와 위상 변위기를 사용한 새로운 측정 기법을 기술한다. 마지막으로 측정 결과를 적용한 송신 펄스 파형에 대한 수신 신호의 펄스 압축 결과로부터 측정 기법의 정확도를 확인하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.30-30
• /
• 2011

The wave-cutoff tool is a new diagnostic method to measure electron density and electron temperature. Most of the plasma diagnostic tools have the disadvantage that their application to processing plasma where toxic and reactive gases are used gives rise to many problems such as contamination, perturbation, precision of measurement, and so on. We can minimize these problems by using the wave-cutoff method. Here, we will present the results obtained through the development of the wave-cutoff diagnostic method. The frequency spectrum characteristics of the wave-cutoff probe will be obtained experimentally and analyzed through the microwave field simulation by using the CST-MW studio simulator. The plasma parameters are measured with the wave-cutoff method in various discharge conditions and its results will be compared with the results of Langmuir probe. Another disadvantage is that other diagnostic methods spend a long time (~ a few seconds) to measure plasma parameters. In this presentation, a fast measurement method will be also introduced. The wave-cutoff probe system consists of two antennas and a network analyzer. The network analyzer provides the transmission spectrum and the reflection spectrum by frequency sweeping. The plasma parameters such as electron density and electron temperature are obtained through these spectra. The frequency sweeping time, the time resolution of the wave-cutoff method, is about 1 second. A short pulse with a broad band spectrum of a few GHz is used with an oscilloscope to acquire the spectra data in a short time. The data acquisition time can be reduced with this method. Here, the plasma parameter measurement methods, Langmuir probe, pulsed wave-cutoff method and frequency sweeping wave-cutoff method, are compared. The measurement results are well matched. The real time resolution is less than 1 ?sec. The pulsed wave-cutoff technique is found to be very useful in the transient plasmas such as pulsed plasma and tokamak edge plasma.

• 대한임상전기생리학회지
• /
• 제2권3호
• /
• pp.13-24
• /
• 2004

The purpose of this study is to reveal the effect of electrical stimulation of body composition in obese person. Subjects were 30s to 40s aged healthy workers(2004. 3. 8~4. 17) in the S general Hospital in Suwon and they were brought to manage obesity. Subjects were divided into control group(Female<0.85, Male<0.90) and study group(Female>0.85, Male>0.90) by WHR(waist-hip ratio) that is measured by Automatic body composition analyzer(InBody 3.0). And we divided the study group with randomized methods into group A(n=8) and group B(n=8). Then we compared and analyzed the change of muscle mass, body fat, abdominal girth, WHR, BMI(body mass index) after application of electrical stimulation, three times a week, for 30 minutes in each session with 50 Hz of pulse frequency, $20\;{\mu}s$ or $250\;{\mu}s$ of pulse duration. There was statistically meaningful decrement of body fat(p<0.05) and abdominal girth(p<0.05) but not of body weight, muscle mass, WHR and BMI in the control group after application of electrical stimulation with 50 Hz, $20\;{\mu}s$. There were meaningful change of abdominal girth(p<0.05), WHR(p<0.05) and BMI(p<0.05), but not of body weight, muscle mass and body fat after application of electrical stimulation with 50 Hz, $20\;{\mu}s$ in group A. We applied electrical stimulation with 50 Hz, $250\;{\mu}s$ in group B, then there were meaningful change of body weight(p<0.05), body fat(p<0.01), abdominal girth(p<0.01), WHR(p<0.05) and BMI(p<0.01) but not of muscle mass only. Consequently, the pulse duration is the main parameter of electrical stimulation that affect the body composition of obese person in this study and if we combined the diet control to reduce blood components we could have better result. So it would be more effective to manage localized obesity(in abdomen, thigh, upper arm, etc.) if you apply electrical stimulation considering the pulse duration.

• Nuclear Engineering and Technology
• /
• 제51권3호
• /
• pp.731-737
• /
• 2019

In this study, a new measurement method based on voltage transients in CdZnTe detectors response to low energy photon irradiations is applied to measure the electron mobility (${\mu}_e$) and electron mobility-lifetime product $({\mu}{\tau})_e$ in a CdZnTe detector. In the proposed method, the pulse rise times are derived from low energy photon response to 59.5 keV($^{241}Am$), 88 keV($^{109}Cd$) and 122 keV($^{57}Co$) ${\gamma}-rays$ for the irradiation of the cathode surface at each detector for different bias voltages. The electron $({\mu}{\tau})_e$ product was then determined by measuring the variation in the photopeak amplitude as a function of bias voltage at a given photon energy using a pulse-height analyzer. The $({\mu}{\tau})_e$ values were found to be $(9.6{\pm}1.4){\times}10^{-3}cm^2V^{-1}$ for $1000mm^3$, $(8.4{\pm}1.6){\times}10^{-3}cm^2V^{-1}$ for $1687.5mm^3$ and $(7.6{\pm}1.1){\times}10^{-3}cm^2V^{-1}$ for $2250mm^3$ CdZnTe detectors. Those results were then compared with the literature $({\mu}{\tau})_e$ values for CdZnTe detectors. The present results indicate that, the electron mobility ${\mu}_e$ and electron $({\mu}{\tau})_e$ values in CdZnTe detectors can be measured easily by applying voltage transients response to low energy photons, utilizing a fast signal acquisition and data reduction and evaluation.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.20-20
• /
• 2010

The effect of excimer laser annealing on the structural and dielectric behaviors of $PbZr_{0.52}Ti_{0.48}O_3$ (PZT) thin films has been investigated. The amorphous PZT thin films were prepared on Pt/Ti/$SiO_2$/Si substrates by a sol-gel method. The PZT precursor was prepared from lead acetate, zirconium acetylacetonate, and titanium isopropoxide. The starting materials were dissolved in n-propanol and 1,3-propanediol. After, the amorphous PZT thin films were laser-annealed (using KrF excimer laser) as a function of the laser energy density and the number of laser pulse. Structural properties of PZT thin films are characterized by using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The dielectric characterization was done on a RT66A test system and a Agilent 4294A impedance analyzer. The PZT thin films show that excimer laser irradiation drastically improved the crystallization and dielectric properties of the PZT thin films, depending on the energy density and the pulse number.

• Nuclear Engineering and Technology
• /
• 제10권3호
• /
• pp.137-144
• /
• 1978

계측장치에서 관측한 계수율에 대한 비직선성 교정을 결정하는 한 방법을 제시하였다. 불감시간은 계수율이 의존성을 가지고 있다는 가정하에서 발전시킨 한 표현식은 실험결과와 잘 일치하였다. 계측장치의 펄스전압의 계수율에 따른 ,변화량을 파고분석장치를 이용하여 측정 하였다. 이 방법은 광범한 계수율 범위에 걸치어 불감시간에 대한 정착찬 값을 주었다. 개요한 이 측정기술로 불감손실로 인한 비직선성의 정확한 교정할 수 있었다. 불감시간은 계수율이 증가함에 따라 감소하는 것이 관측되었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제41회 하계 정기 학술대회 초록집
• /
• pp.254-254
• /
• 2011

The memories with nano-particles are very attractive because they are promising candidates for low operating voltage, long retention time and fast program/erase speed. In recent, various nano-floating gate memories with metal-oxide nanocrystals embedded in organic and inorganic layers have been reported. Because of the carrier generation in semiconductor, induced photon pulse enhanced the program/erase speed of memory device. We studied photo-induced electrical properties of these metal-oxide nanocrystal memory devices. At first, 2~10-nm-thick Sn and In metals were deposited by using thermal evaporation onto Si wafer including a channel with $n^+$ poly-Si source/drain in which the length and width are 10 ${\mu}m$ each. Then, a poly-amic-acid (PAA) was spin coated on the deposited Sn film. The PAA precursor used in this study was prepared by dissolving biphenyl-tetracarboxylic dianhydride-phenylene diamine (BPDA-PDA) commercial polyamic acid in N-methyl-2-pyrrolidon (NMP). Then the samples were cured at 400$^{\circ}C$ for 1 hour in N atmosphere after drying at 135$^{\circ}C$ for 30 min through rapid thermal annealing. The deposition of aluminum layer with thickness of 200 nm was followed by using a thermal evaporator, and then the gate electrode was defined by photolithography and etching. The electrical properties were measured at room temperature using an HP4156a precision semiconductor parameter analyzer and an Agilent 81101A pulse generator. Also, the optical pulse for the study on photo-induced electrical properties was applied by Xeon lamp light source and a monochromator system.

• 대한한방부인과학회지
• /
• 제31권2호
• /
• pp.31-48
• /
• 2018

Objectives: This study was performed to observe the correlations between the results of ABR-2000 and DSOM / 3D-MAC to evaluate the feasibility of ABR-2000 as a oriental medical diagnostic criteria. Methods: We studied 547 women visiting ${\bigcirc}{\bigcirc}$ hospital from December 2012 to June 2015. The subjects were categorized in two groups, 'Hypotonia' and 'Non-Hypotonia' by the result of ABR-2000 and assessed the result of DSOM, 3D-MAC for each group. The differences of pulse wave factors by group also studied. Results: 1. There was no significant difference between two groups about the output frequency of pathogenic factors in DSOM while the result showed the higher correlation in Hypotonia group in terms of the companion tendency of pathogenic factors and syndromes formed by the combination of pathogenic factors. 2. The pulse waves of Hypotonia group were mostly slow, weak, tense and stiff than Non-Hypotonia group. Conclusions: 1. In Hypotonia group, yin deficiency (陰虛) factor was frequently accompanied and consumption (虛損) of various organs based on the yin deficiency (陰虛) was observed. It means chronic and severe condition of exhaustion syndrome (虛勞). 2. The result of 3D-MAC also means pathological feature of yin syndrome (陰 證) and consumption (虛損). Besides, lower scores of Body Surface Area (BSA), body weight, and Body Mass Index (BMI) were associated with body weakness (體瘦), a symptom of exhaustion syndrome (虛勞).