• Journal of KSNVE
• /
• v.2 no.2
• /
• pp.117-123
• /
• 1992

In the study, the design method of reconstruction filter is studied for synchronized sampling which is necessary for order tracking in rotating machinery. The original data sampled at constant intervals, using fixed anti- aliasing filters, is reconstructed by digital reconstruction filter and is resampled at new sampling times calculated by a suitable shaft angle encoder pulse arrival times in order to synchronize with shaft velocity. In addition to eliminating the tracking synthesizer and filters, this new method has no phase noise due to phase-locked loops.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.16 no.4
• /
• pp.276-280
• /
• 2016

A fixed rate speech coder based on the filter bank and the non-uniform sampling technique is proposed. The non-uniform sampling is achieved by the detection of inflection points (IPs). A speech block is band passed by the filter bank, and the subband signals are processed by the IP detector, and the detected IP patterns are compared with entries of the IP database. For each subband signal, the address of the closest member of the database and the energy of the IP pattern are transmitted through channel. In the receiver, the decoder recovers the subband signals using the received addresses and the energy information, and reconstructs the speech via the filter bank summation. As results, the coder shows fixed data rate contrary to the existing speech coders based on the non-uniform sampling. Through computer simulation, the usefulness of the proposed technique is confirmed. The signal-to-noise ratio (SNR) performance of the proposed method is comparable to that of the uniform sampled pulse code modulation (PCM) below 20 kbps data rate.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.20 no.2
• /
• pp.167-174
• /
• 2015

This study describes how digital time delay deteriorates control performance in zero voltage switching (ZVS) phase-shifted full bridge (PSFB) converter. The small-signal model of the ZVS PSFB converter is derived from the buck-converter small-signal model. Digital time delay effects have been considered according to the digital sampling methods. The analysis verifies that digital time delays reduce the stability margin of the converter, and the double sampling technique exhibits better performance than the single sampling technique. Both simulation and experimental results based on 250 W ZVS PSFB confirm the validity of the analyses performed in the study.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.9
• /
• pp.541-545
• /
• 2000

We propose a pulsed $CO_2$laser below 30W by the AC(60Hz) switching control of leakage transformer primary which has some advantages of cost and size compared to a typical pulsed power supply. Pulse repetition rate is adjusted from 5 Hz to 60 to Hz control laser output. In this laser a low voltage open loop control for high voltage pulse discharge circuit is employed to aviod the Hv sampling or switching and high voltage leakage transformer is used to convert low voltage pulse rectified from AC to high voltage one. A ZCS(Zero Crossing Switch) circuit and a PIC(programble one-chip microprocessor are used to control gate signal of SCR precisely. The pulse repetition rate is limited by 60Hz due to the frequency of AC line and a high leadkage inductance. The maximum laser output was about 23 W at pulse repetition rate of 60Hz total gas mixture of $CO_2$ : $N_2$ : He=1: 9: 15 and total pressure of 18 Torr

• The Journal of the Acoustical Society of Korea
• /
• v.9 no.3
• /
• pp.48-55
• /
• 1990

We analyze the effect of second-order sampling on estimating the mean frequency of the Doppler signal. In order to reduce the sampling frequency of analogue-to-digital converter, it is possible to obtain the Doppler signal by sampling the radio frequency echo signal with the low frequence of $4f_0$/5 or $4f_0$/9 instead of $4f_0$, where $f_0$ is the center frequency of the transmitted signal. The computer simulation and experiments show that if the narrowband signal is transmitted as is usual in the Doppler system, the error of the mean frequency estimates due to the low sampling frequency is negligible.

• Journal of the Korean Society for Precision Engineering
• /
• v.12 no.7
• /
• pp.138-147
• /
• 1995

The conventional PWM method, which was used in controlling the on-off valve, such as high-speed solenoid valve, was modulating the width of the pulse applied to the valve, by selecting arbitrary sampling time and modulating the duty-ratio in proportion to the error. However, in this method, a selection of long sampling time was inevitable and it was unable to get a high accuracy and a quick response. This study is for designing an appropriate controller for high-speed solenoid valve by proposing an improved duty-ratio modulation method using the Saw-toothed Carrier Wave which enables a short sampling time selection, high accuracy of control, and a quick response. Test which was carried out in the laboratory shows that transient and steady state response could be improved by PID controller.

• International Journal of Concrete Structures and Materials
• /
• v.1 no.1
• /
• pp.83-88
• /
• 2007

This paper discusses a method of measuring transient potential response of a corrosion interface to a small galvanostatic pulse perturbation for a rapid assessment of the corrosion rate of reinforcing steel in concrete structures. Measurements were taken on 100 mm sections of steel bars which were subjected to a wide range of corrosion conditions, from passive steel to actively corroding steel. The duration of the applied galvanostatic pulse was varied between 5s and 180s, and the lateral distance of the point of measurement on the steel bar varied from zero to 400 mm. The result of the electrochemical transient response was investigated using a typical sampling rate of 1 kHz. Analysis of the transient potential response to the applied galvanostatic pulse has enabled the separation of equivalent electronic components so that the components of a series of capacitances and resistances, whose values are dependent on the corrosion condition of the reinforcing steel, could be isolated. The corrosion rate was calculated from a summation of the separate resistive components, which were associated with the corrosion interface, and was compared with the corrosion rate obtained from linear polarization resistance (LPR) method. The results show that the galvanostatic pulse transient technique enables the components of the polarization resistance to be evaluated separately so as to give more reliable corrosion rate values than those obtained from the LPR method. Additionally, this paper shows how the galvanostatic pulse transient response technique can be implemented. An appropriate measurement time for passive and actively corroding reinforcing steel is suggested for the galvanostatic pulse transient response measurements in the field site.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.31 no.5
• /
• pp.63-71
• /
• 2003

In this paper we dicuss the dither-stripping methods by V-F(voltage to frequency) conversion of the output of angular velocity sensor which is for detecting the dither motion of the ring laser cavity. In this case, it is very important to evaluate the pulse-to-pulse scale factor between the ring lase output pulse and V-F output pulse, and also to compensate the zero offset of the V-F output pulse. In the case of the dither-stripping by the V-F conversion of angular velocity sensor output, there is a big angle uncertainty in the process of compensating the zero offset due to the dither noise for compensating the V-F output. By differential, the phase of the V-F output is changed. So, to compensate it, we change 90deg of the phase of angular velocity sensor output and delay half sampling time of the phase of ring laser output in advance. In this case the pulse-to-pulse scale factor can be evaluated by the standard deviation of each pulse. We can get the good result of the dither-stripping output by this angle differential method.

• Journal of Power Electronics
• /
• v.13 no.2
• /
• pp.232-242
• /
• 2013

To obtain phase currents information in AC drives, shunt sensing technology is known to show great performance in cost-effectiveness and therefore it is widely used in low cost applications. However, shunt sensing methods are unable to acquire phase currents in certain operation conditions. This paper deals with the derivation of the boundary conditions for phase current reconstruction in three-shunt sensing inverters and proposes a voltage injection method to expand the measurable areas. As the boundary conditions are deeply dependent on the switching patterns, they are typically analyzed on the voltage vector plane for space vector pulse width modulation (SVPWM) and discontinuous pulse width modulation (DPWM). In the proposed method, the voltage injection and its compensation are conducted within one sampling period. This guarantees fast current reconstruction and the injected voltage is decided so as to minimize the current ripple. In addition to the voltage injection method, a sampling point shifting method is also introduced to improve the boundary conditions. Simulation and experimental results are presented to verify the boundary condition derivation and the effectiveness of the proposed voltage injection method.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.219.1-219.1
• /
• 2014

전자소자 산업의 미세화 및 대형화에 따라 플라즈마 밀도, 전위, 온도, 균일도 등 과 같은 플라즈마 특성을 제어하는 것은 차세대 플라즈마 장치 개발에 있어 매우 중요한 요소라고 할 수 있다. 특히, 급격한 소자의 미세화에 따라 플라즈마 공정을 통해 발생할 수 있는 damage는 큰 issue가 되어 왔고, 많은 연구자들은 이를 해결하기 위해서 다각적인 노력을 진행해 왔다. 그중 높은 전자 온도는 높은 전자 에너지에 의해 공정 중 소자를 손상 시키는 주된 원인이라고 보고되고 있으며, 이에 대한 제어기술은 매우 중요하다고 할 수 있다. 본 연구에서는 서로 다른 두 개의 내/외측으로 나뉘어진 나선형 모양의 ICP 안테나를 이용 하여 연구를 진행하였다. 내측의 안테나에는 2 MHz를 연결 하였으며, 외측의 안테나에는 13.56 MHz를 연결 하였으며, 내/외측 안테나에 각각 pulse mode로 입력전력을 인가해 줌으로써 플라즈마의 특성을 관찰하였다. Pulse / CW (Continuous Wave) mode에 있어서 전자온도의 측정을 위해 emissive probe 를 이용하여 plasma potential과 floating potential을 측정하였으며, 이를 통하여 전자온도를 계산하여 구할 수 있었다. Duty ratio 및 pulsing frequency의 변화에 따른 전자온도의 변화를 확인 할 수 있었으며, 그에 따른 플라즈마 균일도를 ion saturation current를 측정함으로써 관찰할 수 있었다. 실제 식각 공정에 있어서 Pulsing 조건에 따른 식각 특성을 관찰하기 위해, SiO2, ACL (Amorphous Carbon Layer)에 대해 식각을 진행하였으며, 식각 메커니즘 분석을 위해 이온에너지 분포의 변화를 PSM (Plasma Sampling Mass-spectroscopy)을 이용하여 측정하였다.