• KIEE International Transactions on Electrophysics and Applications
• /
• 제4C권3호
• /
• pp.101-105
• /
• 2004

The efficient power MOSFET inverter applied for a simple and low cost power supply is proposed for driving the dielectric barrier discharge (DBD) lamp load. For decades, the DBD phenomenon has been used for ozone gas production in industry. In this research, the ultraviolet and visible light sources utilizing the DBD lamp is considered as the load for solid-state high frequency power supply. It is found that the simple voltage-source single-ended quasi-resonant ZVS inverter with only one active power switch could effectively drive this load with the output power up to 700 W. The pulse density modulation based control scheme for the single-ended quasi-resonant ZVS inverter using a low voltage and high current power MOSFET switching device is proposed to provide a linear power regulation characteristic in the wide range 0-100％ of the full power as compared with the conventional control based Royer type parallel resonant inverter type power supplies.

• 한국시뮬레이션학회논문지
• /
• 제10권1호
• /
• pp.25-34
• /
• 2001

In this paper, we describe the generation method of interface logic which replace between IP & IP handshaking signal with asynchronous logic circuit. Especially, we suggest the new asynchronous sequential "Waveform to VHDL" code creation algorithm by flow chart conversion : Wave2VHDL - if only mixed asynchronous timing waveform is presented the level type input and pulse type input for handshaking, we convert waveform to flowchart and then replace with VHDL code according to converted flowchart. Also, we confirmed that asynchronous electronic circuits are created by applying extracted VHDL source code from suggest algorithm to conventional domestic/abroad CAD Tool, Finally, we assured the simulation result and the suggest timing diagram are identical.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1992년도 하계학술대회 논문집 B
• /
• pp.1088-1091
• /
• 1992

Programmed PWM(Pulse Width Modulated) generation techniques eliminating several low order harmonics have been widely used in the inverter circuit which produces minimum current ripple, reduced torque pulsation and thereby improves overall system performance. However, the applications of the programmed PWM technique are limited to CVCF(Constant Voltage Constant Frequency) applications and various motor drives. Although the programmed PWM produces a lower harmonic distorted waveform than the carrier modulated PWM, real-time programming is not possible because of the complicated calculation required for the gating signal. In this paper, a new programmed PWM technique named TAM (time averaging model) is developed to compensate for the demerits of the conventional programmed PWM technique with moderate harmonic distortion. Computer simulations are performed to verify the performance of the proposed algorithm.

• Journal of Power Electronics
• /
• 제12권6호
• /
• pp.974-981
• /
• 2012

A FPGA based delta modulated single phase matrix converter has been developed that may be used in both cyclo-converters and cyclo-inverters. This converter is ideal for variable speed electrical drives, induction heating, fluorescent lighting, ballasts and high frequency power supplies. The peripheral input-output and FPGA interfacing have been developed through Xilinx 9.2i, to generate delta modulated trigger pulses for the converter. The controller has been relieved of the time consuming computational task of PWM signal generation by implementing the method of trigger pulse generation in a FPGA by using Hardware Description Language VHDL in Xilinx. The trigger circuit has been tested qualitatively by observing various waveforms on an oscilloscope. The operation of the proposed system has been found to be satisfactory.

• Journal of Power Electronics
• /
• 제9권2호
• /
• pp.164-172
• /
• 2009

Recently, 2-dimensional flat light sources have been attracting much attention for its use in LCD backlight applications because of its high luminous efficiency and uniformity. A long-gap discharge, mercury-tree flat fluorescent lamp has been developed, which shows a high brightness ($>5000\;cd/m^2$) and high luminous efficacy (60 lm/W). Additionally, it has a wide operating margin and stable driving condition with the aid of an auxiliary electrode. For driving the lamp, a narrow pulse power to maintain the glow discharge state is required. Since there has been no research for this kind of lamp driving, this paper proposes a newly developed short-pulse, high-voltage lamp-driving scheme. The proposed lamp system uses a ballast with a coupled-inductor in order to raise the short pulse voltage up to the lamp ignition level and to obtain energy-recovery action during the glow discharge mode. The operation principles are presented and also the system performances such as the lighting efficiency, spatial and angular uniformities are evaluated by hardware experiments. The results show that the proposed lighting system is a good candidate for the next-generation of LCD backlight systems.

• Journal of Welding and Joining
• /
• 제17권5호
• /
• pp.61-68
• /
• 1999

For the last two decades, waveform control techniques have been successively developed and applied for the inverter welding machines resulting in the substantial reduction of spatter generated in CO₂ welding. One of the constituents commonly involved in those techniques is to delay the instant of current increase to some extent after the initiation of short-circuiting. Although this technique has been known to be quite effective in reducing the spatter generation through the suppression of is instantaneous short circuiting, the delay time necessary for minimum spatter has not been clearly understood. In this study, the control system for varying the delay time was constructed so that the spatter generation rates could be measured over a wide range of delay time, 0.29-2.0 msec. As a result of this study, it was demonstrated that spatter generation rate(SGR) sharply decreased at delay time of 0.6 msec and longer accompanied with the change in characteristics of short circuit mode from the instantaneous short-circuiting(ISC) dominant to normal short-circuiting(NSC) dominant. Another feature that have been found in current waveform of over 0.6msec was the creation of current pulse right after the arc reignition stage. Because of this current pulses weld pool oscillated in wave-like fashion and it looks like to play an important role in developing short circuiting between electrode and weld pool.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제6권12호
• /
• pp.3182-3196
• /
• 2012

In this paper, we present a new LED (Light Emitting Diode) mood lighting system interacting with smartphones based on the generation of different light sequences. In the proposed system, one light sequence is considered to be one unit of the service contents, which is then transmitted through a network and played in an LED lighting system. To this end, we propose a novel generation scheme using a smartphone, and a decoding/playing mechanism in an LED lighting system. The lighting sequences have a fixed period divided into predefined time units. Two modes - basic and interpolation - are supported in each time unit when playing a color sequence. In the basic mode, the color is maintained for the entire time unit, whereas in the interpolation mode the color is interpolated. The sequence is decoded and played in the lighting circuit by changing the duty cycle of a PWM (Pulse Width Modulation) signal. A demonstration system of the overall proposed method was using smartphones, a server and an LED lighting system. The results from this experiment show the validity and applicability of the proposed scheme.

• 한국세라믹학회지
• /
• 제43권4호
• /
• pp.259-263
• /
• 2006

The applicability of UPT (Ultrasound Pulse Thermography) for real-time defect detection of the ceramic heating plate is described. The ceramic heating plate with superior insulation and high radiation is used to control the water temperature in underwater environment. The underwater temperature control system can be damaged owing to the short circuit, which resulted from the defect of the ceramic heating plate. A high power ultrasonic energy with pulse duration of 280 ms was injected into the ceramic heating plate in the vertical direction. The ultrasound excited vibration energy sent into the component propagate inside the sample until they were converted to the heat in the vicinity of the defect. Therefore, an injection of the ultrasound pulse wave which results in heat generation, turns the defect into a local thermal wave transmitter. Its local emission is monitored and recorded via the thermal infrared camera at the surface which is processed by image recording system. Measurements were Performed on 4 kinds of samples, composed of 3 intact plates and the defect plate. The observed thermal image revealed two area of crack in the defective ceramic heating plate.

• 전력전자학회논문지
• /
• 제11권3호
• /
• pp.193-200
• /
• 2006

본 논문에서는 효율을 개선하고 인버터 스위칭 주파수를 줄이기 위하여 벅-부스트 형식을 기반의 PWM 전류형 인버터를 내장한 6-pulse-shift 컨버터 구조를 제안한다. 이는 에너지 저장장치 없이 태양광 시스템과 전력계통 사이를 연계하는 시스템으로 사용할 수 있다. 제안된 회로는 초퍼로 동작하는 6개의 전류형 벅-부스트 컨버터와 교류 출력의 극성을 결정하는 한 개의 전파 브리지 인버터로 구성된다. 따라서 제안된 인버터는 스위칭 손실을 줄이고 단위 역률운전을 구현하는 장점을 갖는다. 본 논문에서 이론적인 배경을 논하고 TMS320F2812를 사용하여 구현된 인버터 시작품에 대한 입출력 특성을 실험적으로 입증하였다.

• 한국초전도ㆍ저온공학회논문지
• /
• 제20권1호
• /
• pp.19-22
• /
• 2018

The thermal and electrical properties of the conductor are critical parametersfor the design and optimization of the superconducting magnet. This paper presents simulation code to analyze electrical and thermal stability characteristics of the second generation (2G) high-temperature superconductor (HTS) by varying copper stabilizer thickness. Two types of commercial 2G HTS coated conductor tapes, YBCO and GdBCO were used in this study. These samples were cooled by Liquid Nitrogen ($LN_2$) having boiling at 77.3 K and an equivalent electrical circuit model for them is choosen and analysed in details. Also, an over-current pulse test in which a current exceeding a critical current was performed. From the simulation results, the influences of the copper stabilizer thickness on the stability characteristics of these samples are presented.