• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 춘계학술대회 논문집
• /
• pp.79-80
• /
• 2009

The local oxidation using an atomic force microscopy (AFM) is useful for Si-base fabrication of nanoscale structures and devices. SiC is a wide band-gap material that has advantages such as high-power, high-temperature and high-frequency in applications, and among several SiC poly types, 4H-SiC is the most attractive poly type due to the high electron mobility. However, the AFM local oxidation of 4H-SiC for fabrication is still difficult, mainly due to the physical hardness and chemical inactivity of SiC. In this paper, we investigated the local oxidation of 4H-SiC surface using an AFM. We fabricated oxide patterns using a contact mode AFM with a Pt/Ir-coated Si tip (N-type, $0.01{\sim}0.025\;{\Omega}cm$) at room temperature, and the relative humidity ranged from 40 to 50%. The height of the fabricated oxide pattern ($1{\sim}3\;nm$) on SiC is similar to that of typically obtained on Si ($10^{15}{\sim}10^{17}\;cm^{-3}$). We perform the 2-D simulation to further analyze the electric field between the tip and the surface. Whereas the simulated electric field on Si surface is constant ($5\;{\times}\;10^7\;V/m$), the electric field on SiC surface increases with increasing the doping concentration from ${\sim}10^{15}$ to ${\sim}10^{17}\;cm^{-3}$. We demonstrated that a specific electric field ($4\;{\times}\;10^7\;V/m$) and a doping concentration (${\sim}10^{17}\;cm^{-3}$) is sufficient to switch on/off the growth of the local oxide on SiC.

• Transactions on Electrical and Electronic Materials
• /
• 제8권6호
• /
• pp.241-245
• /
• 2007

[ $(Ba_{0.9-x}Sr_xCa_{0.10})TiO_3$ ] (x=0.33, 0.36) powders were prepared by sol-gel method. $(Ba,Sr,Ca)TiO_3$(BSCT) thick films, undoped and doped with $MnCO_3$ and $Yb_2O_3(0.1{\sim}0.7mol%)$, were fabricated by the screen printing method on the alumina substrate. The coating and drying procedure was repeated 6-times. The Pt bottom electrode was screen printing method on the alumina substrate. These BSCT thick films were annealed at $1420^{\circ}C$ for 2 hr in atmosphere. The upper electrodes were fabricated by screen printing the Ag paste and then firing at $590^{\circ}C$ for 10 min. And then the structured and dielectric properties as a function of the doping amount of $Yb_2O_3$ were studied. As a result of the TG-DTA, exothermic peak was observed at around $670^{\circ}C$ due to the formation of the polycrystalline perovskite phase. All BSCT thick films showed XRD patterns of typical cubic peroveskite structure. The average thickness of BSCT thick films was about $70^{\mu}m$. The curie temperature and the dielectric constant decreased with increasing $Yb_2O_3$ doped content and the relative dielectric constant of the specimen, doped with 0.5 mol% $Yb_2O_3$ at BSCT(54/36/10), showed a best value of 5018 at curie temperature.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.132-132
• /
• 2008

Silicon carbide (SiC) is an attractive material for high-power, high-temperature, and high-frequency applications. So far, atomic force microscopy (AFM) has been extensively used to study the surface charges, dielectric constants and electrical potential distribution as well as topography in silicon-based device structures, whereas it has rarely been applied to SiC-based structures. In this work, the surface potential and topography distributions SiC with different doping levels were measured at a nanometer-scale resolution using a scanning kelvin probe force microscopy (SKPM) with a non-contact mode AFM. The measured results were calibrated using a Pt-coated tip and a metal defined electrical contacts of Au onto SiC. It is assumed that the atomically resolved surface potential difference does not originate from the intrinsic work function of the materials but reflects the local electron density on the surface. It was found that the work function of the Au deposited on SiC surface was higher than that of original SiC surface. The dependence of the surface potential on the doping levels in SiC, as well as the variation of surface potential with respect to the schottky barrier height has been investigated. The results confirm the concept of the work function and the barrier heights of metal/SiC structures.

• 한국재료학회지
• /
• 제10권11호
• /
• pp.778-783
• /
• 2000

고주파 스피터 방법으로 제조된 SnO$_2$감지막 위에 에어로졸 화염 증착법으로 알루미나 표면 보호층을 증착하여 SnO$_2$박막 가스 센서의 감지 특성에 미치는 영향에 대햐여 조사하였고, 표면 보호층에 귀금속 Pt를 도핑하여 Pt의 함량이 CO 및 CH(sub)4 가스들의 선택성에 미치는 영향에 대하여 조사하였다. SnO$_2$박막은 R.F power 50 W, 공정 압력 4 mtorr, 기판온도 20$0^{\circ}C$에서 30분간 0.3$\mu\textrm{m}$ 두께로 Pt 전극 위에 제조하였고, 질산알루미늄(Al(NO$_3$).9$H_2O$) 용액을 희석하여 에어로졸 화염증착법으로 알루미나 표면 보호층을 만든후 $600^{\circ}C$에서 6시간동안 산소분위기에서 열처리하였다. 알루미나 표면 보호층이 증착된 SnO$_2$가스 센서소자의 경우 보호층이 없는 가스 센서와 비교하여 CO 가스에 대한 감도는 매우 감소하였으나 CH$_4$가스에 대한 감도 특성은 순수한 SnO$_2$센서 소자와 비슷하였다. 결과적으로 보호층을 이용하여 CH$_4$가스에 대한 상대적인 선택성 증가를 이룰 수 있었다. 특히 표면 보호층에 Pt가 첨가된 센서 소자의 경우 CO 가스에 대해서는 낮은 감도 특성을 나타내었으나 CH$_4$에 대한 감도는 매우 증가하여 CH$_4$가스의 선택성을 더욱 증대시킬 수 있었다. CH$_4$가스 선택성 향상에 미치는 알루미나 표면 보호층과 Pt의 역할에 대하여 고찰해 보았다.

• 대한화학회지
• /
• 제56권1호
• /
• pp.34-46
• /
• 2012

Dopants and defects can be introduced as well as the intercalation of metals into single wall carbon nanotubes (SWCNTs) to modify their electronic and magnetic properties, thus significantly widening their application areas. Through spinpolarized density functional theory (DFT) calculations, we have systemically studied the following: (i) (10,0) and (5,5) SWCNT doped with nitrogen ($CN_xNT$), (ii) (10,0) and (5,5) SWCNT with pyridine-like defects (3NV-$CN_xNT$), and (iii) chemical functionalization of (10,0) and (5,5) 3NV-$CN_xNT$ with 12 different transition metals (TMs) (Sc, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, Pd, and Pt). Attention was done in searching for the most stable configurations, deformation, calculating the formation energies, and exploring the effects of the doping concentration of nitrogen and pyridine-like nitrogenated defects on the electronic properties of the nanotubes. Also, calculating the corresponding binding energies and effects of chemical functionalization of TMs on the electronic and magnetic properties of the nanotubes has been made. We found out that the electronic properties of SWCNT can be effectively modified in various ways, which are strongly dependent not only on the concentration of the adsorbed nitrogen but also to the configuration of the adsorbed nitrogen impurities, the pyridine-like nitrogenated defects, and the TMs absorbed; due to the strong interaction between the d orbitals of TMs and the p orbitals of N atoms, the binding strengths of TMs with the two 3NV-$CN_xNT$ are significantly enhanced when compared to the pure SWCNTs.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.374.2-374.2
• /
• 2016

Volatile organic compounds (VOCs) in the atmosphere are harmful materials which influence indoor air environment and human health. Titanium dioxide ($TiO_2$) is photocatalyst extensively used in degradation of organic compound. To improve the photocatalytic activity in the visible light region, doping with non-metals element or loading noble metals on the surface of $TiO_2$ is generally proposed. In this study, N- doped $TiO_2$ having photocatalytic activity in visible light region was attached noble metal such as Pt, Ag, Pd, Au by coupling method. Catalytic activities of Noble metal coupled $N-TiO_2$ powders were evaluated by the improvement of their photocatalytic activities and the degradation of VOC gas. A UV-Vis spectrophotometer was used to measure the diffuse reflectance spectra of coupled $N-TiO_2$ sample. The photocatlytic activities of as prepared samples were characterized by the decoloration of aqueous MB solution under Xenon light source (UV and visible light). To measure of decomposition VOCs, ethylbenzene was selected for target VOC material and the concentration was monitored under UVLED irradiation in a closed chamber system. Adjusting the initial concentration of 10~12 ppm, to evaluate the removal characteristics by using the coupled $N-TiO_2$.

• 전기화학회지
• /
• 제15권2호
• /
• pp.90-94
• /
• 2012

We report nanostructure electrodes with $TiO_2$ as a core and carbon as a shell ($TiO_2$@C) for oxygen reduction in alkaline solution. The structure of core-shell electrodes is characterized by transmission electron microscopy, Raman spectroscopy, X-ray diffraction method, and X-ray photoelectron microscopy. The electrochemical properties of the $TiO_2$@C electrodes are characterized using a potentiostat and compared with those of carbon supported Pt catalyst. In particular, the core-shell electrode with dominant pyridinic-N component exhibits an imporved electrocatalytic activity for oxygen reduction reaction in alkaline solution.

• 한국전기전자재료학회논문지
• /
• 제14권7호
• /
• pp.562-566
• /
• 2001

The effects of MnO$_2$ addition on the properties in Pb(Mg$_{1}$3/Nb$_{2}$3/)O$_3$ relaxor ferroelectrics were studied in the phase transition temperature range from -4$0^{\circ}C$ to 11$0^{\circ}C$. Specimens were made via solid state processing method. Dielectric properties, piezoelctric properties, electric-field-induced strain were examined to clarify the effect of MnO$_2$ addition in 0.9MN-0.1PT. As the amount of MnO$_2$ increases, the maximum dielectric constant and the dielectric loss decreases. Q$_{m}$ increased by increasing the doping contents of Mn. When 0.5wt% MnO$_2$ was doped, Q$_{m}$ increased from 95 to 480. The electric-filed-induced strain and polarization decreases as the amount of MnO$_2$ increases. From the experimental results, it was suggested that Mn behaves as an ferroelectric domain pinning element.ent.

• The Korean Journal of Ceramics
• /
• 제6권1호
• /
• pp.43-46
• /
• 2000

$H_4Nb_6/O_{17}$/CdS nanocomposites which intercalated CdS particles, less than 0.8nm thickness, in the interlayer of $H_4Nb_6/O_{17}$ were prepared by the successive ion exchange reactions of $H_4Nb_6/O_{17}$ with $Cd^{2+}$ and $C_3H_7NH_3_+$, followed by the reaction with $H_2S$ gas. $H_4Nb_6/O_{17}$/CdS photocatalytically reduced $NO_3$￣ to $NO_2$￣ and $NH_3$in the presence of sacrificial hole acceptor such as methanol under visible light irradiation (wavelength>400nm), although unsupported CdS showed no noticeable photocatalytic activity for $NO_3$￣ reduction. The catalytic activity of $H_4Nb_6/O_{17}$/CdS greatly enhanced with co-doping of Pt particles in the interlayer.

• 한국전기전자재료학회논문지
• /
• 제17권9호
• /
• pp.947-952
• /
• 2004

Tb-doped lead zirconate titanate(Pb(Zr$\_$0.6/,Ti$\_$0.4/)O$_3$; PZT) thin films on Pt(111)/Ti/SiO$_2$/Si(100) substrates were fabricated by the sol-gel method. The effect on the structural and electrical properties of films measured according to Tb content. The dielectric and ferroelectric properties of Tb-doped PZT thin films were altered significantly by Tb-doping. The PZT thin film with higher dielectric constant and improved leakage current characteristic was obtained by adding 0.3 mol% Tb. The relative dielectric constant and the dielectric loss of the 0.3 mol% Tb-doped PZT thin film were 1611 and 0.024, respectively. Typical value of the swichable remanent poaraization(2Pr) and the coercive filed of the PZT film capacitor for 0.3 mol% Tb-doped were 61.4 ${\mu}$C/cm$^2$ and 61.9 kV/cm, respectively. Tb-doped PZT thin films showed improved fatigue characteristics comparing to the undoped PZT thin film.