• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07b
• /
• pp.739-743
• /
• 2003

[ $Ba_2NaNb_5O_{15}$ ], hereafter BNN, thin films are attractive candidates for nonvolatile memory and electro-optic devices. In the present work, thin films that have different contents of Ba, Nb and Na have been prepared by H-MOD technique on silicon and Pt substrates. XRD and SEM were used to investigate the phase evolution behavior and the microstructure of the films. It was found that the films of about 500nm thick were crack-free and uniform in microstructure. Nb content strongly influenced the phase formation of the films, where unwanted phases were always formed at the stoichiometric BNN composition. However, the unwanted phases decreased with the increase of excess Nb content, and the single phase (tetragonal tungsten bronze structure) BNN thin film was obtained when the niobium content reached some point. From this study, the sub-solidus phase diagram below $850^{\circ}C$ for $BaO-Na_2O-Nb_2O_5$ ternary system is proposed.

• Journal of Magnetics
• /
• v.19 no.3
• /
• pp.227-231
• /
• 2014

We fabricated textured polycrystalline $CoFe_2O_4$ thin films on $Pt(111)/TiO_2/SiO_2/Si$ substrate through a sol-gel method. We varied the thickness of the films, by using precursor solutions with different concentrations of 0.1, 0.2, and 0.3 M, and by depositing 5, 8, or 10 layers on the substrate by spin-coating. X-ray diffraction spectra indicated that when the precursor concentration of the solution was higher than 0.1 M, the spin-coated films were preferentially oriented in the <111> direction. Inspection of the surface morphology by scanning electron microscopy revealed that $CoFe_2O_4$ thin films prepared with 0.2 M solution and 5-time spin-coatings had smoother surface, as compared to the other conditions. Each coating had an average thickness of about 50 nm. The magnetic properties measured by vibrating sample magnetometer showed magnetic anisotropy, as evidenced from the difference in the in-plane and out-of-plane hysteresis loops, which we attributed to the textured orientation of the $CoFe_2O_4$ thin films.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.12
• /
• pp.101-107
• /
• 1995

To improve the leakage current, we developed two step sputtering method where PZT thin film in first deposited at room temperature followed by 600.deg. C deposition. The method used an amorphous PZT layer deposited at room temperature to keep a stable interface during sputtering at high temperature. PZT thin films were deposited on Pt/Ti/SiO$_{2}$/Si substrate at room temperature and 600.deg. C sequentially. The effect of the layer deposited at room temperature was investigated with regard to I-V characteristics and P-E hysteresis loop. In the case of the sample with the layer deposited at room temperature, both leakage current and dielectric constant were decreased. The thicker the layer deposited at room temperature was, the lower dielectric constant was. However, leakage current was indepenent of the variation of the thickness ratio. The sample with 200$\AA$ of the layer deposited at room temperature showed the most promising results in both dielectric constant and leakage current.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.291-293
• /
• 1997

In this study, Sol-Gel derived $(Ba_{0.7}Sr_{0.3})TiO_3$ thin films were fabricated and investigated. The stock solution was synthesized and spin-coated on Pt/Ti/$SiO_2$/Si substrate at 4000(rpm] and then, annealed at $650{\sim}750[^{\circ}C]$. Crystallization condition, microstructural properties and interfacial structure were observed by XRD, AFM, SEM and TEM. It was found that the BST thin films were completely crystallized at 750[$^{\circ}C$] and showed nano-sized grains. The dielectric constant and loss of the BST thin films were 220, 0.01 at 1[kHz] respectively. Increasing the temperature, the dielectric constant and loss characteristics were not varied widely. At the applied voltage of 1.5[V], the leakage current density was under the $10^{-9}[A/cm^2]$.

• Proceedings of the KIEE Conference
• /
• 1999.11d
• /
• pp.918-920
• /
• 1999

Recently, the ceramics of high permittivity are applied to DRAM and FRAM. In this study, (Ba, Sr)$TiO_3$ (BST) ceramics thin films were prepared by Sol-Gel method. BST solution was made and spin-coated on Pt/$SiO_2$/Si substrate at 4000[rpm] for 10 seconds. Coating process was repeated 3 times and then sintered at $750[^{\circ}C]$ for 30 minutes. Each specimen was analyzed structure and electrical characteristics. Thickness of BST ceramics thin films are about $2000[\AA]$. Dielectric constant and loss of thin films was little decreased at $1[kHz]{\sim}1[MHz]$. Dielectric constant and loss to frequency were 250 and 0.02 in BST3. In accordance with applied voltage, property of leakage current was stability when the was $0{\sim}3$[V]. According to voltage, leakage current was increased exponentially at $4{\sim}7$[V].

• Journal of Electrical Engineering and Technology
• /
• v.2 no.1
• /
• pp.98-101
• /
• 2007

Yttrium(Y)-substituted bismuth titanate $(Bi_{4-x},Y_x)Ti_3O_{12}$ [x=0, 0.25, 0.5, 0.75, 1](BYT) thin films were deposited using an RF sputtering method on the $Pt/TiO_2/SiO_2/Si$ substrates. The structural properties and electrical properties of yttrium-substituted $(Bi_4-xYx)Ti_3O_{12}$ thin films were analyzed. The remanent polarization of $(Bi_4-xYx)Ti_3O_{12}$ films increased with increasing Y-content. The $(Bi_{3.25}Y_{0.75})Ti_3O_{12}$ films fabricated using a top Au electrode showed saturated polarization-electric field(P-E) switching curves with a remanent polarization(Pr) of $8{\mu}C/cm^2$ and coercive field (Ec) of 53 kV/cm at an applied voltage of 7 V. The $(Bi_{3.25}Y_{0.75})Ti_3O_{12}$ films exhibited fatigue-free behavior up to $4.5{\times}10^{11}$ read/write switching cycles at a frequency of 1MHz.

• Korean Journal of Materials Research
• /
• v.22 no.2
• /
• pp.86-90
• /
• 2012

Insoluble catalytic electrodes were fabricated by RF magnetron sputtering of Pt on Ti substrates and the performance of seawater electrolysis was compared in these electrodes to that is DSA electrodes. The Pt-sputtered insoluble catalytic electrodes were nearly 150 nm-thick with a roughness of $0.18{\mu}m$, which is 1/660 and 1/12 of these values for the DSA (dimensionally stable anodes) electrodes. The seawater electrolysis performance levels were determined through measurements of the NaOCl concentration, which was the main reaction product after electrolysis using artificial seawater. The NaOCl concentration after 2 h of electrolysis with artificial seawater, which has 3.5% NaCl normally, at current densities of 50, 80 and 140 mA/$cm^2$ were 0.76%, 1.06%, and 2.03%, respectively. A higher current density applied through the electrodes led to higher electrolysis efficiency. The efficiency reached nearly 58% in the Pt-sputtered samples after 2 h of electrolysis. The reaction efficiency of DSA showed higher values than that of the Pt-sputtered insoluble catalytic electrodes. One plausible reason for this is the higher specific surface area of the DSA electrodes; the surface cracks of the DSAs resulted in a higher specific surface area and higher reaction sites. Upon the electrolysis process, some Mg- and Ca-hydroxides, which were minor components in the artificial seawater, were deposited onto the surface of the electrodes, resulting in an increase in the electrical resistances of the electrodes. However, the extent of the increase ranged from 4% to 7% within an electrolysis time of 720 h.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.305-305
• /
• 2010

It is known that a pulse of electrons of high kinetic energy (1-3 eV) in metals can be generated with the deposition of external energy to the surface such as in the absorption of light or in exothermic chemical processes. These energetic electrons are not in thermal equilibrium with the metal atoms and are called "hot electrons" The concept of photon energy conversion to hot electron flow was suggested by Eric McFarland and Tang who directly measured the photocurrent on gold thin film of metal-semiconductor ($TiO_2$) Schottky diodes [1]. In order to utilize this scheme, we have fabricated metal-semiconductor Schottky diodes that are made of Pt or Au as a metallic layer, Si or $TiO_2$ as a semiconducting substrate. The Pt/$TiO_2$ and Pt/Si Schottky diodes are made by PECVD (Plasma Enhanced Chemical Vapor Deposition) for $SiO_2$, magnetron sputtering process for $TiO_2$, e-beam evaporation for metallic layers. Metal shadow mask is made for device alignment in device fabrication process. We measured photocurrent on Pt/n-Si diodes under AM1.5G. The incident photon to current conversion efficiency (IPCE) at different wavelengths was measured on the diodes. We also show that the steady-state flow of hot electrons generated from photon absorption can be directly probed with $Pt/TiO_2$ Schottky diodes [2]. We will discuss possible approaches to improve the efficiency of photon energy conversion.

• Journal of the Korean Magnetics Society
• /
• v.4 no.4
• /
• pp.313-318
• /
• 1994

We have investigated the effects of deposition angle on magnetic and magneto-optic properties in Co/Pt multilayer thin films. which were prepared bye-beam evaporation on tilted substrates. with varying tilt angle from $0^{\circ}$ to $60^{\circ}$. The structure of the specimens was examined by x-ray diffractometer and scanning electron microscope. and the magnetic and magneto-optical properties were measured by VSM, torque magnetometer, and Kerr loop tracer. X-ray diffractometry revealed that all of the specimens had multilayer structure and growth orientation of column followed the tangent rule but the crystallograpic orientation, <111>, was slightly deviated from the substrate normal even though the deposition angle was increased up to $60^{\circ}$. A decrement of the magnetization and Kerr angle with the deposition angle was related with that of the film density due to increasing porosity. The perpendicular mag¬netic anisotropy was also decreased with increasing the deposition angle.

• The Korean Journal of Ceramics
• /
• v.6 no.4
• /
• pp.348-353
• /
• 2000

The effects of MnO$_2$ and Fe$_2$O$_3$ on the piezoelectric properties of 0.05PMN-0.451PT-0.499PZ ceramics were investigated. The addition of MnO$_2$ increased mechanical quality factor (Q$_m$) but decreased the dielectric constant (K$^{T}_{33}$) and compliance (S$^{E}_{11}$) of the specimens. These results indicated that MnO$_2$ behaves as an acceptor in 0.05MN-0.451PT-0.499PZ ceramics. The electromecanical coupling coefficient (K$_P$) of 0.05PMN-0.451PT-0.499PZ ceramics slightly increased with the addition of MnO$_2$ however, the enhancement of $K_P$ was insignificant. A small amount of Fe$_2$O$_3$ was added to enhance the $K_P$ of the 0.05PMN-0.451PT-0.499PZ + 0.5 wt% MnO$_2$ ceramics. The addition of Fe$_2$O$_3$ largely increased $K_P$ through the increase of the K$^{T}_{33}$ and the polarization. The mechanical quality factor of the specimens decreased with the addition of Fe$_2$O$_3$however, the reduction was negligible.