• Transactions of the Korean hydrogen and new energy society
• /
• v.32 no.5
• /
• pp.285-292
• /
• 2021

To study the effect of the mixture ratio of Ni-Pt nanocatalysts on water electrolysis characteristics in anion exchange membrane system, Ni-Pt nanocatalysts were loaded on carbon black by using a spontaneous reduction reaction of acetylacetonate compounds. The loading weight of Ni-Pt nanocatalysts on the carbon black was measured by thermogravimetric analyzer and the elemental ratio of Ni and Pt was estimated by energy dispersive x-ray analyzer. It was found that the loading weight of Ni-Pt nanoparticles was 5.36-5.95 wt%, and the loading weight increased with increasing Pt wt%. As the Ni-Pt loading weight increased, the specific surface area decreased, because Ni-Pt nanoparticles block the pores of carbon black. It was confirmed by BET analysis and dynamic vapor sorption analysis. I-V characteristics were estimated.

• Journal of the Korean Ceramic Society
• /
• v.40 no.2
• /
• pp.118-122
• /
• 2003

The performance evaluation on Pt loading in the self-humidifying polymer electrolyte membrane for Polymer Electrolyte Mem-Brane Fuel Cell(PEMFC) was investigated by using single cell test and measurement of membrane resistance. The self-humidifying membrane comprised two membranes made of perfluorosulfonylfluroride copolymer resin and fine Pt particles tying between them, coated by sputtering. From the results of performance characteristics of self-humidifying membrane cell with different Pt loading, a single cell using self-humidifying membrane with 0.15 mg/$\textrm{cm}^2$ Pt loading showed better performance than that with the others over entire current density. Also, a single cell with 0.15 mg/$\textrm{cm}^2$ Pt loading had a lower resistance value than the other cells under externally nonhumidifying condition. It is indicated that the water produced in the membrane cell with 0.15 mg/$\textrm{cm}^2$ Pt loading showed a higher provision to maintain ionic conductivity of the membrane than the other cells. The optimum amount of Pt particles embedded in the membrane for self-humidifying PEMFC was determined to be about 0.15 mg/$\textrm{cm}^2$.

• Transactions of the Korean hydrogen and new energy society
• /
• v.19 no.6
• /
• pp.467-473
• /
• 2008

This study is to investigate the influence of catalyst loading quantity on the direct methanol fuel cell (DMFC) performance. In this paper, Pt-Ru and Pt-black loading as the catalyst were varied from 1 to $4mg/cm^2$ at the anode and cathode, respectively. The experiment was conducted with single fuel cell consisted of $5cm^2$ effective electrode area, serpentine type flow pattern and Nafion 117 membrane. Also, AC impedance and methanol crossover current were measured to investigate the performance loss precisely. As a result, the performance of fuel cell was significantly increased with the increase of cathode catalyst loading. However, the performance did not increase further above a certain Pt-Ru catalyst loading as the increase of anode catalyst loading.

• 한국신재생에너지학회:학술대회논문집
• /
• 2008.05a
• /
• pp.560-563
• /
• 2008

A modified polyol process is developed to enhance Pt loading during the preparation of Pt/C catalysts. With the help of the zeta potential, the effect of pH on the electrostatic forces between the support and the Pt colloid is investigated. It is shown experimentally that the surface charge on the carbon support becomes more electropositive when the solution pH is changed from alkaline to acidic. However, this change does not affect the electronegative surface charge of Pt colloids already attained and stabilized by glycolate anions. This new behavior caused by the change in the solution pH accounts for the enhanced yield of the process and does not affect the Pt particle size. All our experimental results reveal that this simple modification is a cost effective method for the synthesis of highly Pt loaded Pt/C catalysts for fuel cells.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.1
• /
• pp.105-108
• /
• 2013

To resolve global environmental problems, many automobile companies are making a great deal of effort to develop so-called green-cars. One of the solutions is an electric vehicle equipped with the PEMFC (Proton Exchange Membrane Fuel Cell) stack. However, the cost of the stack, at the moment, is still too high. This obstacle must be resolved for commercialized fuel cell cars. One of the reasons for high cost is a relatively large amount of Pt (platinum) in the membrane. In this paper, a method for reducing the Pt-loading is introduced. Furthermore, the durability of the stack will be important for a company to stay competitive in world markets (in the future). For this, the diagnosis of the stack must be conducted on-line. Some diagnosis methods as key technology are also introduced in this paper.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.200-203
• /
• 2007

Parametric investigation of the polyol process for the preparation of carbon supported Pt nano particles as catalysts for fuel cells was carried out. It was found that the concentration of glycolate anion, which is a function of pH, plays an important role in controlling Pt particle size and loading on carbon. It was observed that Pt loading decreased with increasing alkalinity of the solution. As evidenced by zeta potential measurement, this was mainly due to poor adsorption or repulsive forces between the metal colloids and the supports. In order to modify the conventional polyol process, the effect of the gas purging conditions on the characteristics of Pt/C was examined. By the optimization of the gas environment during the reaction, it was possible to obtain high loading of 39.5wt% with a 2.8 nm size of Pt particle. From the single cell test, it was found that operating in ambient $O_{2}$ at 70oC can deliver high performance of more than 0.6 V at 1.44 A $cm^{-2}$.

• Clean Technology
• /
• v.19 no.1
• /
• pp.59-64
• /
• 2013

Pt/carbon Electrode catalysts for PEMFC were synthesized using colloidal method. PSA (platinum sulfite acid) was used as a Pt precursor and CPA (chloroplatinic acid) was also used to replace relatively expensive PSA. Electrode catalysts prepared using PSA showed Pt particle size less than 3.5 nm and Pt yield higher than 90% in 10~40 wt% Pt loading. Electrode catalysts prepared using CPA also showed Pt particle size less than 4.4 nm and Pt yield higher than 80% in 10~40 wt% Pt loading. The MEA (membrane electrode assembly) using 20 wt% Pt/VXC72 showed equivalent I-V curve comparing with commercial electrode catalyst in single cell test.

• Transactions of the Korean hydrogen and new energy society
• /
• v.33 no.6
• /
• pp.715-722
• /
• 2022

Pt-Fe/carbon black nanocatalysts were prepared by spontaneous reduction reaction of Platinum(II) acetylacetonate and Iron(II) acetylacetonate in a nucleophilic solvent and they were characterized by scanning electron microscopy (SEM), energy dispersive X-ray analyzer (EDS), thermogravimetric analyzer (TGA), transmission electron microscopy (TEM), Brunauer, Emmett and Teller (BET) surface area analysis and anion exchange membrane (AEM) water electrolysis test station. The distribution of the Pt and Fe nanoparticles on carbon black was observed by TEM, and the loading weight of Pt-Fe nanocatalysts on the carbon black was measured by TGA. Elemental ratio of Fe:Pt was estimated by EDS and it was found that elemental ratio of Pt and Fe was changed in the range of 1:0 to 0:1, and the loading weight of Pt-Fe nanoparticles on the carbon black was 5.95-6.78 wt%. Specific surface area was greatly reduced because Pt-Fe nanocatalysts blocked the pores. I-V characteristics were estimated.

• Transactions of the Korean hydrogen and new energy society
• /
• v.33 no.3
• /
• pp.202-208
• /
• 2022

Pt-Ni nanocatalysts were loaded on carbon black by spontaneous reduction reaction of platinum (II) acetylacetonate and nickel (II) acetylacetonate, and they were characterized by transmission electron microscopy (TEM), thermogravimetric analyzer (TGA), energy dispersive x-ray analyzer (EDS), BET surface area and fuel cell test station. The distribution of the Pt and Ni nanoparticles was observed by TEM, and the loading weight of Pt-Ni nanocatalysts on the carbon black was measured by TGA. The elemental ratio of Pt and Ni was estimated by EDS. It was found that the loading weight of Pt-Ni nanoparticles was 5.54 wt%, and the elemental ratio of Pt and Ni was 0.48:0.35. Specific surface area was measured by BET analysis instrument and I-V characteristics were estimated.

• Journal of the Korean Electrochemical Society
• /
• v.14 no.4
• /
• pp.245-252
• /
• 2011

In this study, carbon nanotubes were used as supporter to get high dispersion and high loading of Pt for PEMFC. Thermal oxidation method was applied to carbon nanotubes surface treatment. FT-IR and XPS were used to measure the effect of temperature on functional group. The increased concentration of functional groups was confirmed by XPS analysis, and increased Pt loading and dispersion was also observed by TGA and TEM analysis with increased temperature. Thermal behavior of oxidation is closely related to the manufacture of highly dispersed Pt/MWCNTs. Pt/MWCNTs treatment temperature at $90^{\circ}C$, showed high dispersion and high loading of Pt, and also showed good cell performance.