• Journal of the Korean Magnetics Society
• /
• v.12 no.3
• /
• pp.94-98
• /
• 2002

Sputtering conditions and various underlayer such as Al, Cu, Ni, Cr, Ag, Mg, Fe, Co, Pd, Au, Pt, Mo and Hf were investigated for coercivity enhancement of 20 nm Ti/CoCrPt thin films in order to increase the coercivity of the films thinner than 20 nm. Among them, Ag and Mg were effective to increase the coercivity. Particularly 2 nm Ag was very effective to increase the coercivity and nucleation field as well as to reduce ${\alpha}$ value in CoCrPt thin film such that the coercivity of 2 nm Ag/18 nm Ti/10 nm CoCrPt film was 2200 Oe. However, it seemed that other coercivity enhancement mechanism operated in CoCrPt films because Ti (002) preferred texture was not developed with Ag underlayer contrary to a general expectation. And the coercivity and nucleation field were decreased when glass substrate with rougher surface was used.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.1084-1087
• /
• 2001

The (Sr$\sub$0.85/Ca$\sub$0.15/)TiO$_3$(SCT) thin films are deposited on Pt-coated electrode(Pt/TiN/SiO$_2$/Si) using RF sputtering method. The crystallinity of SCT thin films is increased with increase of substrate temperature in the temperature range of 100[$^{\circ}C$]∼500[$^{\circ}C$]. Also, the crystallinity of SCT thin films are obtained at the substrate temperature above 400[$^{\circ}C$]. SCT thin films had (111) preferred orientation. The dielectric constant changes almost linearly in temperature ranges of-80∼+90[$^{\circ}C$]. The temperature properties of the dielectric loss have a stable value within 0.1. SCT thin films used in this study show the phenomena of dielectric relaxation with the increase of frequency, and the relaxation frequency is observed above 200[kHz].

• Journal of Sensor Science and Technology
• /
• v.1 no.2
• /
• pp.117-123
• /
• 1992

$Pt-SnO_{2-x}$ thin film sensing devices has been fabricated by thermal oxidation of stacked Pt-Sn thin film on the heater. The thickness of Sn thin film deposited by thermal evaporation was $4000{\AA}$ and the thickness of Pt deposited by D. C. sputtering on Sn thin film was $14{\sim}71{\AA}$ range. The XRD analysis show that the $Pt-SnO_{2-x}$ thin films are formed by grains with a diameter of about $200{\AA}$ randomly connected and the crystalline phase of the thin films are preferentally oriented in the (110) direction. $Pt-SnO_{2-x}$ thin film device (Pt thickness : $43{\AA}$) to 6000 ppm CO shows the sensitivity of 80% and high selectivity to CO. And the operating temperature and the thermal oxidation temperature of $Pt-SnO_{2-x}$ thin film device with high sensitivity to CO were $200^{\circ}C$ and $500^{\circ}C$, respectively.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.609-611
• /
• 1997

Pt thin films flow sensors were fabricated by using aluminum oxide films as medium layer and their characteristics were investigated after annealing at $600^{\circ}C$ for 60min. Aluminum oxide improved adhesion of Pt thin films to $SiO_2$ layer without any chemical reactions to Pt thin films under high annealing temperatures. Output voltages increased as gas flow rate and gas conductivity increased because heat loss of heater, which was integrated with a sensing resistor in the flow sensor, increased. Output voltage of flow sensor fabricated on membrane structure was 101mV at $O_2$ flow rate of 2000sccm, heating power of 0.8W while flow sensor fabricated on Si substrate without membrane had output voltage of 78mV under the same conditions.

• Journal of the Microelectronics and Packaging Society
• /
• v.24 no.3
• /
• pp.19-26
• /
• 2017

Stretchable deformation-resistance characteristics of Au, Pt, and Cu films were measured for the stretchable packaging structure where a parylene F was used as an intermediate layer between a PDMS substrate and a metal thin film. The 150 nm-thick Au and Pt films, sputtered on the parylene F-coated PDMS substrate, exhibited the initial resistances of $1.56{\Omega}$ and $5.53{\Omega}$, respectively. The resistance increase ratios at 30% tensile strain were measured as 7 and 18 for Au film and Pt film, respectively. The 150 nm-thick Cu film, sputtered on the parylene F-coated PDMS substrate, exhibited a very poor stretchability compared to Au and Pt films. Its resistance was initially $18.71{\Omega}$, rapidly increased with applying tensile deformation, and finally became open at 5% tensile strain.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.1
• /
• pp.13-17
• /
• 2005

The Pb(Zr/sub 0.52/Ti/sub 0.48/)O₃/(Ba/sub 0.6/Sr/sub 0.4/)TiO₃[PZT/BST] heterolayered thin films were deposited on Pt/Ti/SiO₂/Si substrates by using the RF sputtering method with different RF power. The PZT/BST heterolayered thin films had the tetragonal structure of the PZT phase and BST phase. Increasing the RF power. the intensity of the PZT (100), (110) peaks and BST (111) peaks were decreased and the intensity of the BST (100), (110) peaks were increased. The thickness ratio of the top layered BST thin film and the bottom layered PZT thin film was 2 to1. The atomic concentration of the Ba, Sr, Pb. Zr, Ti atoms were constant in the PZT thin films and BST thin films, respectively. The Pt atom was diffused to the PZT region in the PZT/BST heterolayered thin films deposited at condition of 60[W] RF power. Increasing the frequency, dielectric constant and loss of the PZT/BST heterolayered thin films were decreased. The dielectric constant and loss of the PZT/BST heterolayered thin films deposited with RF power of 90[W] were 406 and 3%, respectively.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.8
• /
• pp.716-722
• /
• 2003

ZnO thin films were deposited on Al and Pt electrodes by an RF reactive sputtering system for the fabrication of FBAR (film bulk acoustic wave resonator), and the effect of thermal treatment temperature on their c-axis preferred orientation was investigated. SEM experiments show that columnar structure of ZnO thin films were grown with c-axis normal to electrode material, and XRD experiments show that both ZnO films were grown with (002) plane preferred orientation, but larger diffraction peak was observed with Pt electrode. The peak intensity increased with higher thermal treatment temperature, but c-axis preferred orientation was diminished. The surface roughness of Al thin film was higher than that of Pt, and these affect the surface roughness of ZnO film deposited on the electrode. Though the preferred orientation with respect to Pt(111) plane was improved with higher thermal treatment temperature, this could not improve the c-axis orientation of ZnO film.

• Journal of Sensor Science and Technology
• /
• v.6 no.5
• /
• pp.400-406
• /
• 1997

The electrical and physical characteristics of aluminum oxide and Pt thin films on it, deposited by reactive sputtering and DC magnetron sputtering, respectively, were analyzed with increasing annealing temperature($400{\sim}800^{\circ}C$) by four point probe, SEM and XRD. Under $600^{\circ}C$ of annealing temperature, aluminum oxide had the properties of improving Pt adhesion to $SiO_{2}$ and insulation without chemical reaction to Pt thin films and the resistivity of Pt thin films was improved. But these properties of aluminum oxide and Pt thin films on it were degraded over $700^{\circ}C$ of annealing temperature because aluminum oxide was changed into metal aluminum and then reacted to Pt thin films deposited on it. The thermal characteristics of Pt micro heater were analyzed with Pt-RTD integrated on the same substrate. In the analysis of properties of Pt micro heater, active area was smaller size, Pt micro heater had better thermal characteristics. The temperature of Pt micro heater with active area, $200{\mu}m{\times}200{\mu}m$ was up to $400^{\circ}C$ with 1.5watts of the heating power.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.2
• /
• pp.153-158
• /
• 2010

The crystallization of FePt/MgO(001) magnetic thin films of various thicknesses has been studied using synchrotron x-ray scattering, atomic force microscope, and vibrating sample magnetometer. In film with a 499-$\AA$-thick, face-centered tetragonal, ordered FePt phase was dominantly crystallized into perpendicular (001) grains keeping the magnetically easy c-axis normal to the film plane during annealing. In film with a 816-$\AA$-thick, however, longitudinal (110) grains keeping the c-axis parallel to the film plane were grown on top of the perpendicular (001) grains. The behavior of the magnetic properties was consistent with the thickness dependence of the crystallization. We attribute the thickness dependence of the crystallization to the substrate effect, which prefers the growth of the c-axis oriented perpendicular grains near the film/substrate interfacial area.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.152-155
• /
• 1996

Platinum thin films were deposited on $Al_2$O$_3$substrate by DC magnetron sputtering for RTD(Resistance Thermometer Devices) temperature sensors. We made Pt resistance pattern on $Al_2$O$_3$substrate by lift-off method and fabricated Pt-RTD temperature sensors by using W-wire, silver epoxy and SOG(spin-on-glass). In the temperature range of 25~40$0^{\circ}C$, we investigated TCR(temperature coefficient of resistance) and resistance ratio of Pt-RTD temperature sensors. TCR values were increased with increasing the annealing temperature, time and the thickness of Pt thin films. Resistance values were varied lineally within the range of measurement temperature. At annealing temperature of 100$0^{\circ}C$, annealing time of 240min and thin film thickness of 1${\mu}{\textrm}{m}$, we obtained Pt-RDT TCR value of 3825ppm/$^{\circ}C$ closed to the Pt bulk value.