• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.10 no.1
• /
• pp.129-136
• /
• 1998

Pressure drop and heat transfer characteristics of a periodically fully developed flow in the flat channel with protrusions are investigated. The effects of shape and location of protrusion on the pressure drop and heat transfer are numerically analyzed in the present study. Taguchi method is used to optimize these parameters. It is found that the ratio of the height of protrusion to channel height shows larger influence on the pressure drop and heat transfer than the ratio of the length of protrusion to module length. As the height of protrusion increases, pressure drop and heat transfer increase, but if the height of protrusion exceeds 2/3 of the channel height, there is a substantial pressure drop. The results also show that the optimal length and height of protrusion are half of the module length and half of the channel height, respectively.

• Proceedings of the KSME Conference
• /
• 2008.11b
• /
• pp.2352-2356
• /
• 2008

Heat transfer and performance characteristics have been investigated for a rectangular wavy duct with dimple or protrusion arrays. The test duct was 15mm in height and 105mm wide. The print diameter of the dimple/protrusion wall was 12.99mm and the depth/height of the dimple/protrusion was 3.75mm. Local heat transfer coefficients on the dimple/protrusion wall were measured using a transient TLC technique. The Reynolds number was varied from 3,000 to 10,000. For the wavy duct tested in this study, adverse static pressure characteristics occurred at turning region of the wavy duct due to secondary flows. For the wavy duct with protrusion array, higher heat transfer enhancement level of 7.4 times than smooth straight case in maximum was obtained at low Reynolds number due to the high heat transfer enhancement by vortex flows. Also, the protrusion array increased the performance level of 3.0 at low Reynolds number of 3,000.

• Journal of Korean Ophthalmic Optics Society
• /
• v.10 no.2
• /
• pp.139-144
• /
• 2005

The purpose of this study was undertaken to determine the analysis of normal values of height of palpebral fissure and Hertel exophthalmometry in Korean woman university students. These measurements were taken from 118 health subjects aged 18-21 years in Korea. In 18-21 years, the mean values of height of palpebral fissure were $6.967{\pm}1.599mm$, $7.172{\pm}1.502mm$, $8.015{\pm}1.44mm$ and $7.1{\pm}1.224mm$, respectively. However, In 18-21 years, the mean values of protrusion were $12.50{\pm}2.33mm$, $12.343{\pm}2.634mm$, $12.773{\pm}1.974mm$ and $13.036{\pm}2.23mm$, respectively. As a results, according to increase the aging, the palpebral fissure height and ocular protrusion was more increase. But in 21 ages the palpebral fissure was some decrease. Also in 19 ages the protrusion was some decrease. On the other hand, the right and left eye have not statistically significant.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.1
• /
• pp.57-63
• /
• 2012

In this study, numerical analyses were performed on pressure drop and heat transfer characteristics in a rectangular horizontal channel with dimple and protrusion arrays of different height. The dimples/protrusions were installed at both top and bottom walls of the rectangular channel. The dimple and protrusion depths are 0.125, 0.2, 0.25, 0.3, and 0.375 times diameter. In case of the dimple, the highest Nusselt number occurred at the rear side of the dimple, and the average Nusselt number tended to decrease slightly with increase of depth. In case of protrusion, on the other hand, the highest Nusselt number occurred at the front side of the protrusion, and the average Nusselt number was increased with the increase of height. In both dimple and protrusion, the average Nusselt number and pressure drop were increased with the increase of velocity. Performance factor was decreased with the increase of velocity, and it was found that the best performance factor was obtained in the low velocity region.

• The korean journal of orthodontics
• /
• v.14 no.2
• /
• pp.233-239
• /
• 1984

The author studied on the tongue position, tongue space and intermaxillary space at 4 groups; normal occlusion 30 cases, Angle's Class I bimaxillary protrusion 29 cases, Angle's Class II malocclusion 26 cases, Angle's Class III malocclusion 26 cases. This study used the data from cephalometric films of female subject aged from 16 to 23 years. Following results were obtained; 1. Dorsal height in Angle's Class III malocclusion was greater than normal occlusion. 2. Anterior Intermaxillary Height in Angle's Class I bimaxillary protrusion and Angle's Class III malocclusion was greater than normal occlusion. 3. Tongue space in Angle's Class I bimaxillary protrusion was greater than normal occlusion. 4. The ratio of the tongue space to the intermaxillary space (T.S./I.S.) in Angle's Class II malocclusion was greater and the ratio in Angle's Class III malocclusion is lesser than normal occlusion.

• The korean journal of orthodontics
• /
• v.28 no.1 s.66
• /
• pp.135-142
• /
• 1998

The purpose of the present study was to evaluate the effect of incisor protrusion on the mucogingival parameters including the width of attached gingiva. Thirty-seven young adults with lower anterior crowding were selected for this study. From the study model, the degrees of relative and absolute protrusions were measured for each lower incisor. Clinical non height, the width of keratinized gingiva, probing depth and the width of attached gingiva were measured with digital vernier calipers and Florida Probe System. Through comparing the difference of the above measurements between protruded and non-protruded incisors, and correlation analysis between each measurement, following results were obtained: 1. The protruded incisor showed narrow width of keratinized and attached gingiva comparing to non-protruded incisor. 2. The protruded incisor showed greater clinical crown height comparing to non-protruded side while there was no difference in the probing depth between protruded and non-protruded side. 3. The difference in the width of attached gingiva between protruded and non-protruded incisors showed higher significance in the lateral incisor than in the central incisor. 4. The degree of relative protrusion showed higher correlation with the width of attached gingiva than the degree of absolute protrusion. 5. Clinical crown height showed higher correlation with the width of attached gingiva than the degree of protrusion.

• Transactions of the Society of Information Storage Systems
• /
• v.11 no.1
• /
• pp.11-15
• /
• 2015

In HDD industry, many technologies have been developed and investigated as means to increase the areal density of drives. Thermal flying-height control has been considered and widely applied in current HDD. When contact occur between TFC slider and disk, the slider has a friction heating induced by highly rotated disk. Moreover, because of the friction heating, additional protrusion of slider can occur. The additional protrusion in contact situation can be a severe effect on head part of slider and disk. Therefore, in this paper, we analyze the friction heating and additional protrusion in contact situation.

• Fashion & Textile Research Journal
• /
• v.23 no.2
• /
• pp.226-236
• /
• 2021

The purpose of this study was to classify the torso shape based on abdominal protrusion caused by changes in the physical characteristics of middle-aged women. This study analyzed 3D shape data of 401 females ranging in age from 40 to 59 years who participated in the 6th Size Korea project. Based on the Size Korea 3D measurement standard, 27 additional items such as height, protrusion, and angle were measured in the 3D scan data. Nine factors were extracted from the analysis of constituent factors of the torso: "vertical size of torso," "flatness and protrusion of abdomen," "torso front extrusion," "upper body height," "bust size and flatness," "size of belly and angle of lower abdomen," "hip length," "hip flatness," and "horizontal size of bust." As a result of the cluster analysis using these nine factors, the torsos of middle-aged women were classified into three types. Type 1 has upper abdominal deposition with a small and long upper body and an advanced abdomen; type 2 has lower abdominal deposition with a small and short torso and a small belly and hip flexion; and type 3 has central abdominal deposition with a big and long torso, large breasts, and protruding abdo¬men front. The middle-aged women were mostly distributed in Type 2. The above results will be useful as basic data for the development of clothing with improved fit to accommodate the changed physical characteristics of middle-aged women.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.6
• /
• pp.781-788
• /
• 2003

In the present study, the heat and flow characteristics of a parallel-flow heat exchanger are numerically analyzed by using three-dimensional turbulent modeling. Heat transfer rate and pressure drop are evaluated using the concept of the efficiency index by varying the locations, the shapes and angles of inlet/outlet, and the protrusion height of flat tube. It is found that negative angle of the inlet improves the heat transfer rate and pressure drop. Results show that the locations of the inlet and outlet should be toward the right side and the left side to the reference model, respectively, in order to enhance the heat transfer rate and pressure drop. Increasing the height of the lower header causes pressure drop to decrease and yields the good flow characteristics. The lower protrusion height of flat tube shows the improvement of the heat transfer rate and pressure drop. The heat transfer rate is greatly affected by the parameters of outlet side such as the location and angle of the outlet. However, the pressure drop is influenced by the parameters of inlet side such as the location and angle of inlet and the height of the header.

• The korean journal of orthodontics
• /
• v.30 no.2 s.79
• /
• pp.185-196
• /
• 2000

Patients who want to reduce their lip protrusion usually estimate the severity of the lip protrusion on the frontal aspect. Most orthodontists have a perplexed experience of a reduced thin line of vermilion border on the frontal aspect as incisors we retracted, even though the lip protrusion is thought to be reduced favorably on the sagittal aspect. Some patients also look older after orthodontic treatment because of severe lip thinning. This unaesthetic reduction of vermilion border urges us to study the vertical lip change during orthodontic procedure. The purpose of this study was to evaluate the vertical lip and perioral soft tissue changes in respect to incisor retraction in an effort to analyze which factors might be responsible for their vertical changes, using the multiple regression analysis. The results were as follows. 1. Upper and lower lip philtrum length(SnLs, LiB') were increased after retraction of anterior teeth, where as upper and lower vermilion height(LsSuls, StmiLi), and vermilion length(LsLi) were decreased. 2. Upper and lower lip length(SnStms, StmiB'), and soft tissue lower anterior facial height(SnMe') did not show any significant difference after treatment. 3. The increase of the upper lip philtrum length was mainly influenced by the extrusion of upper anterior teeth(${\Delta}U1V$), and the increase of the lower lip philtrum length was mainly influenced by the initial overjet before treatment. 4. The decrease of the upper and lower lip vermilion height was mainly influenced by the decrease of upper lip thickness.