• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.4
• /
• pp.28-35
• /
• 2021

Infrared (IR) stealth technology to protect aircraft from heat-tracking missiles is a very important factor in the development of military aircraft. In this study, the intensities of signal generation were compared by observing the IR signals generated from the plumes of the engine and identifying them for each measurement angle. To simulate a jet engine applied to an actual aircraft, a small turbojet engine was constructed, the infrared signal characteristics for each wavelength were identified according to the measurement angle, and the total infrared radiance was derived by integrating the signal for each wavelength. Through this study, we intend to present basic data for improving the infrared stealth performance of aircraft.

• Journal of ILASS-Korea
• /
• v.12 no.2
• /
• pp.86-93
• /
• 2007

There is a growing interest to develop an eco-friendly air cleaner with high performance through a remanufacturing process. Two kinds of polyurethane filter media, a coarse (Filter-A) and a fine filter media (Filer-B), are used in this study to protect a vehicle engine from airborne particles. In order to improve the collection performance of the filters (Filter-A, Filter-B), an oil coating technology on the filter surface was introduced. As a result, inertial force is a dominant collection mechanism for a dry filter media, so that collection efficiency increases with increasing filtration velocity. However, intra-structure change of an oil-coated filter media influences on the collection mechanism, which shows a non-linear collection efficiency curve in terms of filtration velocity. The result shows that the developed filter media are eco-friendly and effective to protect a vehicle engine from airborne particles especially at low filtration velocity.

• Aerospace Engineering and Technology
• /
• v.9 no.2
• /
• pp.193-197
• /
• 2010

Water cooling ducts are installed in the exhaust diffuser for high altitude tests of rocket engine to protect diffuser from high-temperature combustion gas. The mass flow rate and pressure of cooling water is designed to prevent boiling of cooling water in the ducts. Therefore, the estimation of maximum temperature of duct wall is important parameter in design of cooling system, especially pressure of cooling water. The method for predicting maximum temperatures of duct walls with variation of coolant flow rates was derived theoretically.

• Tribology and Lubricants
• /
• v.9 no.2
• /
• pp.36-48
• /
• 1993

This study is concerned with the changes (deterioration) of the mechanical properties of used oil in the gasoline engine. The analysed properties of used oil were friction, antiwear, wear debris, load-carrying ability and the formation of surface film. From this study, it was found that the oil used in engine was deteriorated to increase the wear and fricion and decrease the load-carrying ability as the running distance of oil was increased. Also the main cause of deterioration was related to the formation of the protective film on the contact zone. When the film was composed with rich additives (sulfur), this could properly protect contact zone from the increase of wear and friction. But as oil was deteriorated, it could not form such a film and therefore the protective ability of sliding surface diminished.

• Journal of Power System Engineering
• /
• v.17 no.4
• /
• pp.17-22
• /
• 2013

Diesel generator of nuclear power plant has a role for supply of emergency electric power to protect reactor core system in event of loss of off-site power supply. Therefore diesel generator should be tested periodically to verify the function that can supply specified frequency and voltage at design power level within limited time. For this purpose, appropriate maintenances in case that abnormal conditions were found are required in allowed time. In this paper, results of development of engine condition diagnosis technology and study on power plant of its technology for diesel generator are described.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1997.10a
• /
• pp.70-75
• /
• 1997

Power driving shaft systems with reduction gear are frequently equipped with elastic couplings to protect reduction gears and to relieve the torsional vibration problems. In this study, torsional vibration characteristics for the engine shafting system with elastic couplings are investigated and the calculating program is developed. It is confirmed that torsional vibration can be controled by careful selection of a elastic coupling with suitable characteristics and the suitability of a elastic coupling can only be determined as a result of a complete torsional vibration analysis including engine conditions such as misfring for shafting system.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.06a
• /
• pp.160-165
• /
• 2005

The proceeding bearings of marine diesel engine are affected by dynamic loads from the cylinder gas pressure and the inertia force from the crank mechanism. Oil film must support the load of the shaft and it also must protect the proceeding and the bearings from damage. This study uses Goenka's new curve fit to carry out the theoretical analysis of oil film in proceeding bearings for MAN B&W 12K90MC-C and Hyundai Heavy Industry Co., Ltd HiMSEN H21/32 Engine. The applied engine's analysis results show the behavior of the proceedings in main and crank pin bearings. The results of this study will be the proper criteria for the proceeding bearings design and be available for development of the new technology in the proceeding bearing and for the high strength lining coating.

• Tribology and Lubricants
• /
• v.24 no.3
• /
• pp.122-128
• /
• 2008

To reduce the friction losses and the wear amounts in the piston assembly two methods were proposed. One is the modification of surface profile of the skirt part. The surface coating is another method to protect the sliding surfaces. To modify the profile of the skirt surfaces the surfaces were ground to have three different shapes of profiles. Also, several coatings, such as graphite, TiN, and $MoS_2$, and DLC, were used to protect the surfaces of the piston skirts. The specimens of the skirt and the cylinder bores were tested with the reciprocating wear tester. SAE 5W40 engine oil was used in boundary lubrication regime. Among several coatings the graphite and DLC coatings were very effective to reduce the friction forces. Especially, DLC film represented much better tribological performances than the others. The friction coefficient of the graphite coating was the lowest, but the graphite coating was not effective to protect the surfaces.

• Safety and Health at Work
• /
• v.8 no.2
• /
• pp.226-230
• /
• 2017

The performance of sound barriers was evaluated to determine their technical effectiveness and practicality in reducing noise exposures to operating engineers in construction. Commercially purchased sound dampening mats (SDMats) were installed inside three heavy-equipment engine compartments. Sound pressure levels (SPLs) were measured before and after installing the SDMats while the equipment was on idle and full-throttle settings where it normally operates. SPLs inside the heavy-equipment operator cabs were significantly reduced by 5.6-7.6 dBA on the full-throttle setting following installation of the SDMats (p < 0.01). The evaluated engineering control intervention was simple to install, affordable, and substantially reduced the engine noise reaching the heavy-equipment operator, potentially reducing reliance on hearing-protection devices to protect construction workers from noise exposures.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.7
• /
• pp.1378-1384
• /
• 2011

In this paper, the electromagnetic shielding performance of a BiMODAL Tram is investigated by means of an electromagnetic analysis tool, called HFSS. For the purposed of doing this, first, three-dimensional finite element modeling for the tram including electronic devices and engine room is carried out. Then, for quantitatively assessing the electromagnetic shielding performance of the tram's body, concentration indexes for electric field magnitude and time-average stored electric energy are introduced. From numerical results, it is inferred that the tram's body can protect the electronic devices and engine room against external electromagnetic waves from 30 MHz to 100 MHz.