• Journal of Power Electronics
• /
• 제11권5호
• /
• pp.639-654
• /
• 2011

This paper presents a Current Distribution Control design for Paralleled Positive Output Elementary Super Lift Luo Converters (PPOESLLCs) operated in Continuous Conduction Mode using a Sliding Mode Controller (SMC). Manipulating the higher current requirement of the load through the paralleling of POESLLCs, results in a current inequality. This is mainly due to dissimilarities in the power semiconductor switches and circuit components used in POESLLCs, which may lead to converter failures. In order to balance the proper load current sharing and the load voltage regulation of PPOESLLCs, a SMC is developed. The SMC is designed for the inherently variable-structured of POESLLCs by using the state-space average based model. The static and dynamic performance of the developed controller with PPOESLLCs is validated for its robustness to perform over a wide range of operating conditions through both a laboratory prototype and MatLab/Simulink models, which are compared with a Proportional-Integral (PI) controller. Theoretical analysis, simulation and experimental results are presented to demonstrate the feasibility of the developed SMC along with the complete design procedure.

• Journal of Power Electronics
• /
• 제18권6호
• /
• pp.1708-1719
• /
• 2018

A complete current loop decoupling control strategy based on a sliding mode observer (SMO) is proposed to eliminate the influence of current dynamic coupling and back electromotive force (EMF) in the vector control of permanent magnet synchronous motors. With this strategy, current dynamic decoupling and back EMF compensation can be simultaneously achieved. Unlike conventional methods, the proposed strategy can avoid the disturbances caused by the parametric variations of motor systems and maintain the advantages of proportional integral (PI) controllers, which are robust and easy to operate. An improved SMO, which uses a special PI regulator other than a linear saturation function as the equivalent control law in the boundary layer of a sliding surface, is proposed to eliminate the estimated errors caused by the quasi-sliding mode and obtain a satisfactory decoupling performance. The stability and parameter robustness of the proposed strategy are also analyzed. Physical experimental results are presented to verify the validity of the method.

• 전기전자학회논문지
• /
• 제23권2호
• /
• pp.628-635
• /
• 2019

본 논문에서는 일정 스위칭 주파수를 가지는 직접 토크 제어(Direct Torque Control, DTC) 기반의 매입형 영구자석 동기 전동기(Interior Permanent Magnet Synchronous Motor, IPMSM)에서 속응성 향상을 위한 슬라이딩 모드 제어(Sliding Mode Control, SMC) 기법을 제안한다. 일정 스위칭 주파수를 가지는 DTC 기법은 비례-적분(Proportional-Integral, PI) 토크 제어기와 삼각파 비교기로 구성되어 토크 오차 상태를 일정하게 제어한다. 이는 일반적인 히스테리시스 기반의 DTC 기법에 비해 속응성이 좋지 않다. 본 논문에서는 SMC 기법을 이용하여 일정 스위칭 주파수를 가지는 DTC 기법의 속응성을 향상시키는 방법을 제안한다. 제안하는 기법의 타당성을 시뮬레이션을 통하여 검증한다.

• Smart Structures and Systems
• /
• 제29권4호
• /
• pp.617-624
• /
• 2022

A new intelligent adaptive control scheme was proposed that combines the control based on interference observer and fuzzy adaptive s-curve for flight path tracking control of unmanned aerial vehicle (UAV). The most important contribution is that the control configurations don't need to know the uncertainty limit of the vehicle and the influence of interference is removed. The proposed control law is an integration of fuzzy control estimator and adaptive proportional integral (PI) compensator with input. The rated feedback drive specifies the desired dynamic properties of the closed control loop based on the known properties of the preferred acceleration vector. At the same time, the adaptive PI control compensate for the unknown of perturbation. Additional terms such as s-surface control can ensure rapid convergence due to the non-linear representation on the surface and also improve the stability. In addition, the observer improves the robustness of the adaptive fuzzy system. It has been proven that the stability of the regulatory system can be ensured according to linear matrix equality based Lyapunov's theory. In summary, the numerical simulation results show the efficiency and the feasibility by the use of the robust control methodology.

• Journal of Power Electronics
• /
• 제16권1호
• /
• pp.297-309
• /
• 2016

Grid-connected inverters (GCIs) with an LCL output filter have the ability of attenuating high-frequency (HF) switching ripples. However, by using only grid-current control, the system is prone to resonances if it is not properly damped, and the current distortion is amplified significantly under highly distorted grid conditions. This paper proposes a synchronous reference frame equivalent proportional-integral (SRF-EPI) controller in the αβ stationary frame using the parallel virtual resistance-based active damping (PVR-AD) strategy for grid-interfaced distributed generation (DG) systems to suppress LCL resonance. Although both a proportional-resonant (PR) controller in the αβ stationary frame and a PI controller in the dq synchronous frame achieve zero steady-state error, the amplitude- and phase-frequency characteristics differ greatly from each other except for the reference tracking at the fundamental frequency. Therefore, an accurate SRF-EPI controller in the αβ stationary frame is established to achieve precise tracking accuracy. Moreover, the robustness, the harmonic rejection capability, and the influence of the control delay are investigated by the Nyquist stability criterion when the PVR-based AD method is adopted. Furthermore, grid voltage feed-forward and multiple PR controllers are integrated into the current loop to mitigate the current distortion introduced by the grid background distortion. In addition, the parameters design guidelines are presented to show the effectiveness of the proposed strategy. Finally, simulation and experimental results are provided to validate the feasibility of the proposed control approach.

• 항공우주시스템공학회지
• /
• 제11권1호
• /
• pp.14-21
• /
• 2017

매우 큰 정안정성($C_{L{\alpha}}$)을 갖는 틸트덕트 운동모델에 대해 선형 파라미터를 갖는 Sigma-Pi 신경망(SPNN) 제어법칙을 적용하였다. 기존의 비례적분미분(PID) 제어기는 매우 큰 정안정성을 갖는 운동모델이 갖는 강한 기수숙임 문제를 해결하기 어려웠고 이로인해 제어성능을 높일 수 없었다. 이와 달리 외부루프와 내부루프에 모두 적용된 SPNN 제어기는 동역학역변환 및 모델오차를 줄일 수 있는 의사적응제어 명령을 이용해서 과도한 안정성을 개선할 수 있었다. 이를 검증하기 위해서 경로점 추종 시뮬레이션을 이용해서 PID제어 성능과 SPNN제어 성능을 비교하였다.

• 전력전자학회논문지
• /
• 제20권6호
• /
• pp.517-525
• /
• 2015

A grid connected inverter must be operated as the main electricity source under an isolated condition caused by the grid problem. Conventionally, the dual loop controller is used for the grid inverter, and the controller is used for control under the stand-alone mode. Generally, the PI(Proportional - Integral) controller is highly efficient under a synchronous reference frame, and stable control can be available. However, in this synchronous frame-based control, high-quality DSP is required because many sinusoidal calculations are necessary. When the PI control is conducted under a stationary frame, the controller constructions are made simple so that they work even with a low-price micro controller. However, given the characteristics of the PI controller, it should be designed with the phase of reference voltage considered. Otherwise, the phase delay of the output voltage can occur. Although the current controller also has a higher bandwidth than the voltage controller, distortion of the voltage is difficult to avoid only by the rapid response of the PI controller, as a sudden load change can occur in the nonlinear load. In this study, a new control method that solves the voltage controller bandwidth problem and rapidly copes with it even in the nonlinear load situation is proposed. The validity of the proposed method is proved by simulation and experimental results.

• 한국조명전기설비학회지:조명전기설비
• /
• 제9권4호
• /
• pp.103-110
• /
• 1995

Fuzzy theory is recently finding wide popularity in various applications that include management, economics, medicine and process control system. This paper describes application of fuzzy logic in a current control system that use a inverter welding machine. The Fuzzy control is then extended to the current loop control, replacing the conventional proportional-integral(PI) control methods. The fuzzy control algorithms have been developed in detail and verified by experiments of a inverter welding system. The experimentation study indicates the superiority of fuzzy control over the I control methods. Fuzzy control seems to have a lot of promise in the applications of welding process control system.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.2143-2146
• /
• 2003

We propose, for the first time to our knowledge, a novel gain-clamping method for EDFA in WDM Add/Drop networks by introducing a disturbance observer technique. The proposed gain-clamping control input consists of the nominal gain-clamping control such as PI(Proportional and Integral) control and the additional control input for the compensation of the effects caused by channel add/drops. The additional control input is designed using the wellknown disturbance observer technique and can be implemented very easily with general electric elements. We proved the superiority of the new technique over the previous methods by showing simulation result of minimized dips and spikes that appear in power profile of EDFA output.

• 전력전자학회논문지
• /
• 제22권1호
• /
• pp.1-8
• /
• 2017

The optimal gain design method of a three-phase boost converter is proposed in this study. The control system has a two-loop configuration, in which each controller is coupled closely; thus, the optimal design is difficult to achieve using conventional gain-tuning method. The proposed method is adopted to the MATLAB SISO TOOL software and is based on the controller requirements, which are phase margin and cut-off frequency of the open-loop system. The optimal proportional -integral gains can be designed easily using the proposed interactive method of the SISO TOOL. The performance of the proposed system is verified through simulation and experiments.