• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.9
• /
• pp.868-882
• /
• 2009

In this paper, channel model and wireless link performance analysis for the short-range wireless communication system applications in the terahertz frequency which is currently interested in many countries will be described. In order to realize high data rates above 10 Gbps, the more wide bandwidths will be required than the currently available bandwidths of millimeter-wave frequencies, therefore, the carrier frequencies will be pushed to THz range to obtain larger bandwidths. From the THz atmospheric propagation characteristics based on ITU-R P.676-7, the available bandwidths were calculated to be 68, 48 and 45 GHz at the center frequencies of 220, 300 and 350 GHz, respectively. With these larger bandwidths, it was shown from the simulation that higher data rate above 10 Gbps can be achieved using lower order modulation schemes which have spectral efficiency of below 1. The indoor propagation delay spread characteristics were analyzed using a simplified PDP model with respect to building materials. The RMS delay spread was calculated to be 9.23 ns in a room size of $6\;m(L){\times}5\;m(W){\times}2.5\;m(H)$ for the concrete plaster with TE polarization, which is a similar result of below 10 ns from the Ray-Tracing simulation in the reference paper. The indoor wireless link performance analysis results showed that receiver sensitivity was $-56{\sim}-46\;dBm$ over bandwidth of $5{\sim}50\;GHz$ and antenna gain was calculated to be $26.6{\sim}31.6\;dBi$ at link distance of 10m under the BPSK modulation scheme. The maximum achievable data rates were estimated to be 30, 16 and 12 Gbps at the carrier frequencies of 220, 300 and 350 GHz, respectively, under the A WGN and LOS conditions, where it was assumed that the output power of the transmitter is -15 dBm and link distance of 1 m with BER of $10^{-12}$. If the output power of transmitter is increased, the more higher data rate can be achieved than the above results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.10
• /
• pp.1142-1149
• /
• 2007

In this paper, the development of wideband MIMO channel sounder and a pilot measurement result is described for research on the multi antenna radio propagation characteristics considering urban environment at microwave frequencies. We developed $4{\times}4$ MIMO(BW:100 MHz) channel sounder using the high speed switching mechanism and periodic pseudo random binary signals method considering next generation mobile communication system. A pilot measurement campaign at the urban area of Bundang is presented for confirmation of system performance. From the analysis of measurement data, wideband path loss exponent of 3.7 and 8 GHz band is 1.79 and 1.76. Average RMS delay spread is 200 ns and 42 ns respectively. From the experiment results, operation of this measurement system is confirmed considering research for a coverage, SNR and channel capacity in urban environment at microwave frequencies.

• The Transactions of the Korea Information Processing Society
• /
• v.5 no.5
• /
• pp.1311-1319
• /
• 1998

The methods of providing available bandwidth adaptively using feedback to maximize the utilization of network as well as the quality of service have been the focus of recent research activities for ATM(Asynchronous Transfer Mode). This study has been extended from the point-to-point connection to a point-to-multipoint environment as the number of applications requiring multicast service increases. It is known that the effectiveness of feedback based congestion control scheme diminishes as propagation delay increases. Especially for a multicast connection consisting of various paths and destinations with different performance and congestion status, the problem of unfairness due to different propagation delays may occur. The degree of such unfairness may change depending on various aspects of congestion control schemes. These has been, however, relatively little study on these problems. In this paper, we present how various aspects of control schemes-length of the interval between feedback generations, point of time to coalesce feedback cells from child paths, decreasing factor of source rate in case of congestion-affect the degree of unfairness. Simulation results show that degree of unfairness changes according to when the feedback coalescing happens. Expecially it is shown that the effect of feedback coalescing time to the degree of unfairness is more significant for the smaller feedback interval. It is also found that as the source rate decreasing factor becomes larger the average ACR(Allowed Cell Rate) at the source gets lower and the degree of unfairness grow larger.

• The KIPS Transactions:PartD
• /
• v.13D no.7 s.110
• /
• pp.901-908
• /
• 2006

With the development of wireless communication techniques and mobile environment we are able to transmit data between mobile systems without restriction of time and space. Recently, researches on the data communication between mobile systems have focused on a small amount of sending out or receiving data and data synchronization at a fixed server and mobile clients in mobile environment. However, two more servers should be able to move mutual independently, information is shared with other systems, and data is synchronized in the special environment like a battlefield situation. Therefore, we propose a data synchronization method between systems moving mutual independently in mobile environment. The proposed method is an optimization solution to data propagation path between servers that considers limited bandwidth and process of data for disconnection communication. In addition, we propose a data reduction method that considers importance and sharing of information in order to reduce data transmission between huge servers. We verified the accuracy of data after accomplishing our data synchronization method by applying it in the real world environment. Additionally, we showed that our method could accomplish data synchronization normally within an allowance tolerance when we considered data propagating delay time by server extension.

• Journal of the Korean Geophysical Society
• /
• v.3 no.2
• /
• pp.127-138
• /
• 2000

This study was conducted to examine the differences between dynamic and static elastic constants by use of some laboratory tests of cement mortar specimens which have different water/cement mixing ratios. Specific gravity measurement, ultrasonic velocity estimating and uniaxial compression test were adopted to acquire the dynamic and static elastic constants. Digital data acquisition and processing enhanced the accuracy of estimating the velocities of specimens drastically, Also, the method using the gradient of propagation delay time in according to increment of specimen length more enhanced the accuracy than the method using the only one specimen length over total propagation time. The correlation between density and the P and S wave velocity of specimens shows reliable positive relation and the correlation between density and the strength of uniaxial compression has the similar relationship. The dynamic Young's modulus $(E_D)$ is alway greater than the static Young's modulus $(E_S)$ and there is increasing tendency of the ratio $(E_D/E_S)$ according to the increase of density or strength of the specimens. On the other hand, there is no typical relationship between dynamic Poisson's ratio $({\nu}_D)$ and static Poisson's ratio $({\nu}_S)$ and just the ratio of ${\nu}_D/{\nu}_S$ ranges front 69 to 122 %.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.1
• /
• pp.138-145
• /
• 2007

Wireless transmission system using the multipath channel is affected ISI due to the delay spread. So we use a decision feedback equalizer which consist of decision part and feedback filter for remove the ISI effectively. In this paper, we propose a improved adaptive decision feedback equalizer to mitigate ISI effectively. The proposed adaptive decision feedback equalizer is construct by using soft decision device and hierarchical feedback filter based on MMSE sub-optimal equalizer using the LMS algorithm. Soft decision device mitigate the error propagation in feedback filter by incorrectly detected decision symbol and feedback filter which is divided two step independently mitigate the ISI by using a adaptive algorithm. As a result this structure shows better performance than conventional decision feedback equalizer by mitigating the error propagation in filter cause incorrectly detecting symbol. and we get the MSE more rapidly by using larger step-size due to reduce the number of feedback filter tap. In computer simulation, we compare the bit error rate performance of proposed decision feedback equalizer with conventional one on the S-V channel model for UWB system.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.11 no.6
• /
• pp.757-763
• /
• 2018

It is very difficult to achieve sufficient data rate and required quality of service due to the time-varying nature of the radio channel and various jammers such as path loss, delay, Doppler, shadowing and interference. Especially, the propagation path between the transmitting antenna and the tracking antenna mounted on the fuselage during the test and evaluation of the projectile system considered in this paper is based on the rapid movement of the projectile, the interference due to multipath fading due to the terrain, The propagation path may be blocked. In order to effectively improve the multipath fading occurring in the wireless communication system, a diversity combiner technique is required. In this paper, to derive the design and improvement schemes for the space diversity combiner technique among the diversity combiner schemes, the BER performance of maximum ratio combining (MRC) and selection combining (SC) In an adaptive SC / MRC diversity combiner that operates with MRC when it is lower than the specified threshold criterion when comparing the SNR between two signals received from the channel and operates with SC at high and combines the two received signals The BER performance of the system was compared and analyzed.

• The Transactions of the Korea Information Processing Society
• /
• v.5 no.6
• /
• pp.1610-1619
• /
• 1998

The ABR service class provides feedback based traffic control to transport bursty data traffic efficiently. Feedback based congestion control has first been studied to be applied to unicast connections. Recently. several congestion control algorithms for multicast connections have also been proposed as the number of ABR applications requiring multicast increases. With feedback based congestion control, the effectiveness of a traffic control scheme diminishes as propagation delay increases. Especially for a multicast connection, a remote destination may suffer unfair service compared to a local destination due to the delayed feedback. Amelioration of the disadvantages caused by feedback delay is therefore more important for remote destinations in multicast connections. This paper proposes a new switch behavior to provide effective feedback based mathc control for rentoh destinations. The proposed switches adjust the service rate dynamically in accordance woth the state of the downstream, that is, the congestion of the destinaion is immediately controlled by the nearest apstream switch before the source to ramp down the transmission rate of the connection. The proposed switch has an implementation overhead to have a separate buffer for each VC to adjust the service rate in accordance with a backward Rm cell of each VC. The buffer requirement id also increased at intermediate switches. Simulation results show that the proposed switch reduces the cell loss rate in both the local and the remote destinations and slso amelioratd the between the two destinations.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.2
• /
• pp.179-187
• /
• 2010

The use of high frequency band, broad band and MIMO antenna is expected in the next generation mobile communication system. By the rapid increase of demand for wireless communications and the explosive increase of the mobile communication services, researches for optimization of next-generation mobile communication system are required. In the existing MIMO channel models, propagation-environments are commonly classified into urban, suburban, rural area, etc. However such approaches can have drawbacks in that many different morphologies may exist even in the urban area, for example. In this paper, we introduced path morphology concept, and proposed the method of morphology classification considering the building height, density, etc. Delay spread(DS), angular spread(AS) of AoD and AoA analyzed for each environment using the ray tracing technique. Based on the analysis, a MIMO channel model appropriate in domestic environment was suggested.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.6
• /
• pp.447-458
• /
• 2003

A high speed multiplier is essential basic building block for digital signal processors today. Typically iterative algorithms in Signal processing applications are realized which need a large number of multiply, add and accumulate operations. This paper describes a macro block of a parallel structured multiplier which has adopted a 32$\times$32-b regularly structured tree (RST). To improve the speed of the tree part, modified partial product generation method has been devised at architecture level. This reduces the 4 levels of compression stage to 3 levels, and propagation delay in Wallace tree structure by utilizing 4-2 compressor as well. Furthermore, this enables tree part to be combined with four modular block to construct a CSA tree (carry save adder tree). Therefore, combined with four modular block to construct a CSA tree (carry save adder tree). Therefore, multiplier architecture can be regularly laid out with same modules composed of Booth selectors, compressors and Modified Partial Product Generators (MPPG). At the circuit level new Booth selector with less transistors and encoder are proposed. The reduction in the number of transistors in Booth selector has a greater impact on the total transistor count. The transistor count of designed selector is 9 using PTL(Pass Transistor Logic). This reduces the transistor count by 50% as compared with that of the conventional one. The designed multiplier in 0.25${\mu}{\textrm}{m}$ technology, 2.5V, 1-poly and 5-metal CMOS process is simulated by Hspice and Epic. Delay is 4.2㎱ and average power consumes 1.81㎽/MHz. This result is far better than conventional multiplier with equal or better than the best one published.