• Journal of the Korean housing association
• /
• v.16 no.5
• /
• pp.91-98
• /
• 2005

The purpose of this study is to analysis of propagation characteristics for floor impact noise in attendance upon investigating standard of insulation performance, measurement and evaluation, understanding characteristics of a measuring factor for floor impact noise in apartment houses. Four cases which was before occupied apartment in Daegu was selected for experiment. Floor impact noise of measurement and evaluation method which are specified in the Korea Standard 2810-1, 2810-2, 2863-1 and 2863-2 was selected for this study. As the result of this study, 1) Especially, there is not a difference for apartment size, but the apartment of 40py type is lower than 30py's about $1\~2\;dB$ for light-weighted and heavy weighted impact sound. 2) The floor impact sound insulation performance is similar about measurement location of the same floor structure. 3) The floor impact sound insulation performance is not a difference about the slab area.

• Advanced Composite Materials
• /
• v.16 no.2
• /
• pp.151-166
• /
• 2007

High-cycle fatigue characteristics of quasi-isotropic carbon fiber reinforced plastic (CFRP) laminates [-45/0/45/90]s up to $10^8$ cycles were investigated. To assess the fatigue behavior in the high-cycle region, fatigue tests were conducted at a frequency of 100 Hz, since it is difficult to investigate the fatigue characteristics in high-cycle at 5 Hz. Then, the damage behavior of the specimen was observed with a microscope, soft X-ray photography and a 3D ultrasonic inspection system. In this study, to evaluate quantitative characteristics of both transverse crack propagation and delamination growth in the high-cycle region, the energy release rate associated with damage growth in the width direction was calculated. Transverse crack propagation and delamination growth in the width direction were evaluated based on a modified Paris law approach. The results revealed that transverse crack propagation delayed under the test conditions of less than ${\sigma}_{max}/{\sigma}_b$ = 0.3 of the applied stress level.

• Journal of Ocean Engineering and Technology
• /
• v.17 no.3 s.52
• /
• pp.46-51
• /
• 2003

Acoustic emission (AE) signals, emanated during local failure of aluminum alloys, have been the subject of numerous investigations. It is well known that the characteristics of AE are strongly influenced by the previous thermal and mechanical treatment of the sample. Possible sources of AE during deformation have been suggested as the avalanche motion of dislocations, fracture of brittle particles, and debonding of these particles from the alloy matrix. The goal of the present study is to determine if AE occurring as the result of fatigue crack propagation could be evaluated by the joint time-frequency analysis method, short time Fourier transform (STFT), and Wigner-Ville distribution (WVD). The time-frequency analysis methods can be used to analyze non-stationary AE more effectively than conventional techniques. STFT is more effective than WVD in analyzing AE signals. Noise and frequency characteristics of crack openings and closures could be separated using STFT. The influence of various fatigue parameters on the frequency characteristics of AE signals was investigated.

• Journal of Advanced Marine Engineering and Technology
• /
• v.25 no.1
• /
• pp.115-123
• /
• 2001

This study describes the combustion characteristics under various condition of air excess ratio and ignition timing in a 2-valve gasoline optically accessible engine with swirl control valve(SCV). It adapted three different types of SCA(open ration 72.5%, 78%, 89%) to strengthen a swirl flow. Pressure data were acquired using pressure sensor to investigate the effect of swirl flow on combustion, and from these pressure data, IMEP(indicated mean effective pressure) and MFB(mass fraction burnt)were calculated to explain burn rate and flame speed. From acquired flame images, inspected the flame propagation direction, flame area, and flame centroid, Flame propagation direction was shown different tendency between with/without SCV, and flame area with SCV was faster and larger than that of conventional engine. Finally, the representative flame image at each crank angle were acquired by PDF method to verify flame growth process. It is found that strengthened swirl flow is more beneficial for faster and stable combustion.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.125-133
• /
• 2002

In this study, it was investigated about endurance limit and fatigue behavior of load carrying fillet welded cruciform joints according to welding methods of SMAW, SAW, MIG and FCAW commonly using for welding structures in present. Endurance limit carried omit highly in the order of SMAW, MIG, SAW, FCAW and fatigue crack propagation ratio carried out lowly in the order of SMAW, MIG, FCAW, SAW. By these results, it is needed to use SMAW or MIG welding methods for welding structures with small welding capacity and SAW or FCAW methods for large welding structures after due consideration about economic gains and operation efficiency of welding. Fatigue crack propagation ratio is more effected by strength of welding materials than endurance limit of welding materials according to welding methods.

• Proceedings of the IEEK Conference
• /
• 1998.06a
• /
• pp.177-180
• /
• 1998

In high frequency environment such as microcell, it is requried to adopt a new method different from the empirical channel modeling applied in macrocell. In this thesis, measurement for residential area in Sinrimdong and the result of the simulation are compared and analyzed. Simulation technique utilizes 3D ray launching method to consider some factors which were not included in the ray tracing method. Propagation environment in the urban area shows the typical channel characterisitics of the propagation environment. Using 3D ray launching method, pathloss of the wave and delay characteristics of the signal with respect to the height of the transmitter is researched. If the transmitter is located on the top of the building, radiowave experiences diffraction on the rooftop and it influences the total received signal strength.

• Proceedings of the IEEK Conference
• /
• 1998.06a
• /
• pp.165-168
• /
• 1998

This paper describes the characteristics of CT-2 radio wave propagation at 900MHz range. Typical cell coverage of CT-2 based on picocellular design provides a 200m radius. The five sites of urban regions of Kwang Ju city were chosen to characterize propagation in various environments. On the basis of cell coverage data measured with field strength meter, average 75% of telepoint service was retained and it was lack 25% of overall gain. In some sites telepoint service was limited to two of four directions around a station. If specially designed collinear antenna with specific directivities are used in these shadow area, improved results will be acquired.

• The Journal of the Acoustical Society of Korea
• /
• v.20 no.4E
• /
• pp.45-51
• /
• 2001

This paper examines the dispersion relation governing the wave propagation on cylindrical shells. The assumption of thin shells allows the dispersion relation to be separated into three relations related to the propagation of flexural waves and two types of membrane waves. Those relations are used to identify the characteristics of the wave number curves. The dispersion relation provides two and three closed wave number curves below and above the ring frequency. Above the ring frequency three wave number curves are clearly identified to be those of flexural, shear and longitudinal waves, respectively. Below the ring frequency, the characteristics of two wave number curves are identified with dependence of the direction of wave propagation.

• Progress in Superconductivity and Cryogenics
• /
• v.2 no.1
• /
• pp.35-35
• /
• 2000

The main issues for the power application of High Tc superconducting tape are lower AC loss and higher stability conditions. HTS tape has large stability margin by high heat capacity of superconductor itself and high temperature margin. But, it can be damaged by continuous heat generation at quench point, because normal zone propagation velocity by generating heat is very low. Here, we analyze the quench propagation characteristics using finite element method for BSCCO-2223 HTS tape.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.852-855
• /
• 2004

This experimental study describes the propagation characteristics of the impulse noise emitted from the exit of a straight pipe attached to the open end of a simple shock tube. The sound pressure level and directivity of the impulse noise propagating from the exit of pipe with several different diameters are measured in the far sound fold for the range of the incident shock wave Mach number between 1.07 and 1.26. The experimental results showed that the peak values of impulse noises had a strong dependance on the exit diameter of a pipe and the shock wave Mach number. The impulse noise had the directivity propagating toward to the pipe axis and the characteristics of inverse square law of propagation distance. Moreover, it was shown that the one-third octave band SPL of impulse noise was almost constant regardless of the frequency band.