• Journal of Food Hygiene and Safety
• /
• v.27 no.3
• /
• pp.257-263
• /
• 2012

Cosmetics using natural materials which was purchased in retail stores, distributed in Gyeonggi province(32 samples) and online through internet(24 samples) were analyzed by pesticide residues and target preservatives for assessing the safety of it. Natural or organic certifications was identified in 22 samples among 56 samples and most of them were Ecocert. Pesticide residues was detected in 3 samples among 56 samples and each compound and concentration was permethrin(0.6 mg/kg), tricyclazole(11.7 mg/kg) and malathion(0.05 mg/kg). All of it was purchased through internet. Target preservatives was detected in 13 samples among 56 samples and one of them was over the maximum allowed concentration and the rest of them were within the maximum allowed concentration of the respective preservatives. The compound which was over the maximum allowed concentration was benzoic acid and compounds which were within the maximum allowed concentration were sorbic acid, benzoic acid and methylparaben. They were all identified substances in products and the number of detected preservatives in retail stores were higher than online samples purchased through internet. As a result of this study, The method of analyzing pesticide residues and limit in cosmetics using natural materials should be set up as soon as possible and the monitoring about preservatives in cosmetics using natural materials should be conducted on continuously.

• Applied Chemistry for Engineering
• /
• v.28 no.5
• /
• pp.501-505
• /
• 2017

Due to the rapid urbanization and increased population, there is an increase in airtight nature of buildings which causes serious indoor air pollution. Among several indoor air pollutants, volatile organic compounds (VOCs) emitted from paint are of major concern. Therefore, there is an urge for the development of environmental friendly paint products. In this wok, a natural wall paint (NWP) was prepared by utilizing a natural clay material "sericite" as a main component. A small chamber test was carried out to identify the toxic substances release from NWP and the results were compared with two eco-friendly commercial paints. The total VOCs were detected in trace level inside the test chamber and their concentrations were below the recommended indoor air quality standards. Toluene was not detected for NWP, whereas formaldehyde was observed in trace level. The toxicity index results were compared with two commercial paints and found that NWP exhibited less harmful gas emission. Based on certification rating of building materials, NWP can be classified as the first grade of building materials. Due to the above advantages, the use of sericite as a major component in NWP will be a useful technique to maintain the indoor air quality.

• Clean Technology
• /
• v.24 no.2
• /
• pp.146-153
• /
• 2018

The water footprint is an important component of the Single Market for Green Product initiative based on the EU's Roadmap to a Resource Efficient Europe. In July 2014, the EU has established the International Standard for Water Footprint (ISO 14046) and Korea has complied with the Korean Industrial Standard (KS I ISO 14046) in April 2015. If a certification system based on the international standard (ISO 14046) is introduced, developing countries such as India and Vietnam, which are not equipped with bases, can become a trade barriers in exporting, so Korea should establish a strategy to reverse them. On the other hand, water footprints are designed to take into account local environmental impacts when compared to similar footprints (eg, carbon footprint) using LCA, so that products manufactured and manufactured in Korea will have an impact on domestic waters Should be considered. Therefore, the method of the water footprint should conform to the standard for compatibility with other countries. In order to consider the domestic water condition, it is necessary to identify suitable indicator or factor for estimating water footprint on Korea. For this purpose, this study analyzed the water footprint estimation study conducted at domestic and foreign based on international standards and through the analysis of statistical data related to domestic water resources, we confirmed the applicability of the water footprint methodology in Korea.

• Journal of the Korean BIBLIA Society for library and Information Science
• /
• v.26 no.3
• /
• pp.83-100
• /
• 2015

This paper aims to survey the supply status and demand of the scientific & technological information among the 1,059 small enterprises demanding the support in Busan, Ulsan and Gyeongsangnam-do which have been supported by the Branch of KISTI and to propose the approaches to improve the scientific & technological information system. As the results of this research, Busan, Ulsan and Gyeongsangnam-do have very poor business and R&D environment to the extent that 96.3% of businesses was small business (medium business only for 3.7%) and 31% of total small & medium-cized businesses has less than 10 R&D workers. Small & medium-sized businesses which have demanded the information to KISTI account for only 0.2% in average for 3 years. The information demand types are market trend (26.8%), industrial property right (22.1%), business proposal (19.9%), item exploration (16.8%) and quality certification (8.4%). The supplied informations include scientific and technological data survey, market survey, translation and information application seminar. The business achievements from the information supply include 379 cases in technological development improvement and launch of products, 88 cases in technology certifications and 414 cases in patents and utility design application and registration. By the analysis results, the small and medium-sized businesses have difficulties in using R&D information by themselves. Thus, it's proposed to establish the science and technology information center in southeastern region and develop the information advisors specialized in local specialty industry categories. It's also proposed to expand the manpower and budget of KISTI concerning the information support for small & medium-sized businesses.

• Fire Science and Engineering
• /
• v.31 no.5
• /
• pp.63-69
• /
• 2017

This study describes the development of a long-distance hose for ultra-high pressure operation, which can be used in conjunction with an ultra-high pressure pump and can be effectively applied to the fire suppression of high-rise buildings and a long, large tunnels. Also, it has phosphorescent properties, which can help to secure the withdrawal route of the fire-fighters when they are threatened by the fire. We developed an ultra-high pressure hose aiming at a pressure of 3 MPa and a flow rate of 2000 lpm and developed an ultra-high pressure fire hose that can withstand this very high pressure by using a double jacket, triple polyurethane coating and warf (Wp) of 52. In order to ensure the performance of the developed ultra-high pressure hose, its structure, appearance, leakage at high pressure, length and elongation were inspected by a certified certification agency, who also subjected it to a peeling test, friction test, breaking pressure test and free fall test. Also, it was studied in addition to the luminescent high-pressure hose for fire-fighting. In the phosphorescence test, the luminance measurement value was more than the reference value of the luminance test after 40 minutes, which confirmed that its performance was satisfactory for fire-fighting products. In the future, if such an ultra-high pressure fire hose were commercialized and applied in the field, it could contribute to securing improved fire suppression and safer exit from fires, as compared to the fire hoses currently used in the suppression of fires in skyscraper buildings and long tunnels.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.29 no.5
• /
• pp.1099-1116
• /
• 2019

Industrial control systems(ICS) are widely used in various industrial area and critical infrastructure. To mitigate security threats on ICS, the security assurance test for industrial control devices has been introduced and operating. The test includes testing of the security function of the device itself and testing of communication robustness. In this paper, we describe the security requirements of EDSA, Achilles, and Korea's TTA standard(security requirements for ICS). And also, we analyzed the characteristics of communication robustness test(CRT) of each certification. CRT verifies the device's operation of essential function while transmitting fuzzing and stress packets. Existing test methods are mostly focused on the embedded devices and are difficult to apply to various devices. We propose a method to test communication robustness which reflect the characteristics of control H/W, control S/W, field devices and network devices in ICS. In the future, we will apply the proposed communication robustness test to actual products and present solutions for arising issues.

• Journal of Practical Engineering Education
• /
• v.13 no.2
• /
• pp.327-332
• /
• 2021

Materials used for education include SM20C, Al6061, and acrylic. SM20C materials are used a lot in certification tests and functional competitions as carbon steel, but they are also used in industrial sites. Al6061 is said to be a material that produces a lot of tools because it has lower hardness than carbon steel and is highly flexible. When practical guidance is given to students using acrylic materials, it is a material that causes vibration and tool damage due to excessive cutting. In this process, we examine how impact on the 5-axis equipment 2NC head can affect precision control. The weakest part of a five-axis equipment is the head that controls the AC axis. In the event of precision and cumulative tolerances in this area, the precision of all products is reduced. Thus, a key part of the 2NC head, the spindle housing was carried out using Al7075 T6 (U.S. Alcoasa) material and the entire body using FCD450 (spherical graphite cast iron). In the vibration and cutting process acting on these two materials, the analysis was carried out to determine the value of applying the force as a finite element analysis under extreme conditions. We hope that using these analytical data will help students see and understand the structure of 5-axis machining rather than 5-axis cutting.

• Journal of the Society of Disaster Information
• /
• v.17 no.1
• /
• pp.184-193
• /
• 2021

Purpose: In this study, since the operation principle of the CCFL Exit light is the same as that of general lighting equipment, the characteristics of the CCFL Exit light were analyzed by deriving test items that can affect the characteristics of the light source from the KS standard, which is the standard for lamp ballast performance certification of general lighting equipment. Method: The samples used in the experiment were performed on products of two manufacturers for each size, such as large, medium, and small, and the test items were power factor, crest factor, and current harmonic distortion. Result: As a result of the experiment, the power factor showed a value between 0.4 and 0.6 in all samples, which was smaller than the 0.9 value set by KS. The crest factor ranged from 3.6 to 3.7 for large, 4.4 to 4.7 for medium, and 3.5 to 3.7 for small. It showed a value more than two times higher than the KS standard of 1.7. Current total harmonic distortion ranged from 81% to 110%, and considering that the KS standard was less than 20%, it could be confirmed that all samples had a value significantly exceeding the KS standard. Conclusion: The crest factor and current total harmonic distortion may affect the temperature rise of the light source and the burnout of the device. When developing an exit light, if this item is developed within the scope of the KS standard, the quality improvement and maintenance of the exit light will be greatly improved.

• Journal of Practical Engineering Education
• /
• v.14 no.1
• /
• pp.119-125
• /
• 2022

Materials used for education are materials such as SM20C, Al6061, and acrylic. SM20C materials are carbon steel and are often used in certification tests and functional competitions, but are also widely used in industrial sites. The Al6061 material is said to be a material that has lower hardness and stronger flexibility than carbon steel, so it is a material that generates a lot of compositional selection of tools. If students are taught practical training using acrylic materials, vibration occurs due to excessive cutting in some parts and damage to the tool occurs. In this process, we examine to what extent the impact on the 2NC head, which is a five-axis equipment, can affect precision control. The weakest part of the five-axis equipment can be said to be the weakest part of the head that controls the AC axis. When the accuracy and cumulative tolerance of this part occur, the accuracy of all products decreases. Therefore, the core part of the 2NC head, the spindle housing, was carried out using an Al7075 T6 (Alcoa, USA) material. In the process of vibration and cutting applied to this material, the analysis was conducted to find out the value applied to the finite element analysis under extreme conditions. It is hoped that this analysis data will help students see and understand the structure of 5-axis machining rather than 5-axis cutting.

• Journal of the Korea Institute of Building Construction
• /
• v.23 no.6
• /
• pp.703-714
• /
• 2023

This research conducts a series of tests to investigate the setting retarding properties and strength development in cement pastes incorporating various types and dosages of sugar-based super retarding agents. Six such agents, including Sucrose, Sugar powder, Saccharin, Aspartame, Stevioside, and Mogroside, commercially available, were selected for evaluation. The study also examines the micro-structural properties of these cement pastes. The test mixtures were prepared using a 27.5% water-to-cement ratio and ordinary Portland cement. Micro-structural analyses were conducted using Scanning Electron Microscopy(SEM), X-Ray Diffraction(XRD), and Energy Dispersive Spectroscopy(EDS). The findings reveal that the incorporation of sucrose, sugar powder, and stevioside significantly retards the setting time. Particularly, adding 0.1% sucrose extended the setting time by approximately two-fold compared to the control(Plain) mixture. Most mixtures, barring those with sugar powder and stevioside, exhibited compressive strength comparable to the Plain mixture. Notably, with 0.2% sucrose, strength measurements were not feasible at 1 day, but at 3 days, the strength gains aligned with the Plain mixture. XRD, SEM, and EDS analyses confirmed the hydration delay(set retarding) of C3S due to sucrose, with further quantitative corroboration provided by EDS. SEM was used to verify the presence or absence of hydration products. The study concludes that sucrose, as a sugar-based retarder, offers effective set retarding capabilities and compressive strength development in concrete.