• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.21 no.3
• /
• pp.269-275
• /
• 2003

The cadastral system which accomplishes the base of national land administration with accuracy of proper data and the cadastral maintenance quickly is agreeing with the actual place in information ages in Inundation. But even in spite of many efforts, various Problems are exposed in accuracy of the data on the cadastral maps and local situation must agree accurately from the process which propels cadastral information systems. Therefore, it must be carried out the cadastral non correspondence arrangement first of all in link of the plan which it corrects the error of existing data and computerization quickly. It summarizes the research as follows ; Cadastral non correspondence of the land boundaries on the map and actual circumstance does not agree with cadastral maps accurately, The lands which exceed the standards with the position error excess of 50cm on lil ,200 and 240cm on 1/6,000 areas on the map scale are the registration correction objectives. It is investigated that the cadastral non correspondence parcels occur in various cause and long period, the area error corrections are mainly objectives, and about 80% of the test area comes to reveal within permitted the limit of the measurement of planimetric area for cadastral survey, so it is not difficult with the fact that the compensation back which it follows in area increase and decrease and the location error correction becomes the important object fer the cadastral non correspondence arrangement projects.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.2 no.3
• /
• pp.189-199
• /
• 2004

A bridge transported servo manipulator (BTSM) system for the advanced spent fuel conditioning process (ACP) has been developed to overcome the limitation of access, which is a drawback of mechanical master-slave manipulators (MSM) for the equipment maintenance. The servo manipulator is composed of a slave manipulator attached to the telescoping tubesets equipped with the overhead bridge installed at a hot cell and a master manipulator installed at an out-of-hot cell. Each manipulator has 7 degrees-of-freedom (DOF): a body rotation, an upper-arm tilt, a lower-arm tilt, a lower-arm rotation, a wrist pan & tilt, and a grasp motion. A wire-driven mechanism for a lower-arm rotation, a wrist pan and tilt, and a grasp motion of the manipulator has been adopted to increase the handling capacity compared to the manipulator weight and decrease the friction. The main disadvantage of the wire-driven mechanism is that if one link is in motion, other links can be affected. In this paper, the transmission characteristics among the wire-driven links have been formulated to overcome this drawback. The unexpected behaviors are confirmed by analyses of transmission characteristics as well as experiments. Also, the experimental results show that the unexpected behaviors are greatly decreased by the proposed compensation equations.

• Health Policy and Management
• /
• v.28 no.3
• /
• pp.195-196
• /
• 2018

The Korean Academy of Health Policy and Management (KAHPM) has shown remarkable achievements in the field of health policy and management in Korea for the last 30 years. The KAHPM consists of experts in various fields of health policy and management, and has been the leading academic discussion forum for health policy agendas of interest to the public. Health Policy and Management (HPM), the official journal of the KAHPM, published the first issue of volume 1 in October, 1991 and is publishing the second issue of volume 28 as of 2018. Currently, it is one of Korea' main journals in the field of health policy and management. HPM has published a special issue in commemoration of the 30th anniversary of the KAHPM. The HPM invited authors, including former presidents of the KAHPM and current board members, to write about main issues in health policy and management. Although the HPM tried to set up an invited author on all subjects in the health policy and management field, 19 papers are published, that completed the peer review process by August, 2018. The authors of the special issue of the 30th anniversary of the KAHPM include six former presidents, a senior professor, and 12 board members. The subjects of this issue are reform of the healthcare delivery system, health insurance and medical policy, reform of health system governance, the role of National Health Insurance Service (NHIS), the Korea Institute for Health and Social Affairs (KIHASA) and the National Evidence-based healthcare Collaborating Agency (NECA), ethical aspects of health policy change, regional disparities of healthcare, healthcare accreditation, new healthcare technology evaluation system, globalization of the healthcare industry, the epidemiological investigator system, the quarantine system, safety and disaster, and official development assistance. There are some remaining topics to deal with for the KAHPM: aged society, anti-smoking, non-infectious disease, suicide, healthcare resources, emergency medical care, out-of-pocket money, medical fee payment system, medical aid system, long-term care insurance, industrial accident compensation insurance, community-centered health welfare system, and central government and local government of health. The HPM will continue to publish review articles on the main topics in health policy and management. This is because the KAHPM, which has been the leading academic society of Korea's health policy and management for the last 30 years, feels responsible for continuing its mission for the next 30 years.

• Korean Journal of Construction Engineering and Management
• /
• v.14 no.4
• /
• pp.46-54
• /
• 2013

This research outlined the factors influencing the business management success via analyzing a survey of business principles. The research process has been tested in comparison of both financial factors, which come out of objective data and non-financial factors so relevantly prioritized by combining these factors. In order to specify the factors, a check-list and analyzed essential features of category have been done with interviews and surveys. As consequently proceeding, the authors could deduce that non-financial but analytic factors such as business do-able, technician workability, compensation and benefits etc. play major roles in construction sector. The outcomes consider a construction business as fundamental human labor job as opposed to a manufacture business. On reasoning necessarily more objective research works to be done as developing this research's outcome, it is meaningful in suggesting the pivotal factors influencing the construction business management. Therefore, this research is expected to guide the direction to induce the improvement of business management to be done by further exemplary researches.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.3
• /
• pp.517-531
• /
• 1999

This paper presents the development of the 2-mode variable gain high power amplifier for a transmitter of INMARSAT-M operating at L-band(1626.5-1646.5 MHz). This SSPA(Solid State Power Amplifier) is amplified 42 dBm in high power mode and 36 dBm in low power mode for INMARSAT-M. The allowable error sets +1 dBm of an upper limit and -2 dBm of a lower limit, respectively. To simplify the fabrication process, the whole system is designed by two parts composed of a driving amplifier and a high power amplifier, The HP's MGA-64135 and Motorola's MRF-6401 are used for driving amplifier, and the ERICSSON's PTE-10114 and PTF-10021 are used the high power amplifier. The SSPA was fabricated by the circuits of RF, temperature compensation and 2-mode gain control circuit in aluminum housing. The gain control method was proposed by controlling the voltage for the 2-mode. In addition, It has been experimentally verified that the gain is controlled for single tone signal as well as two tone signals. The realized SSPA has 42 dB and 36 dB for small signal gain within 20 MHz bandwidth, and the VSWR of input and output port is less than 1.5:1 The minimum value of the 1 dB compression point gets 5 dBm for 2-mode variable gain high power amplifier. A typical two tone intermodulation point has 32.5 dBc maximum which is single carrier backed off 3 dB from 1 dB compression point. The maximum output power of 43 dBm was achieved at the 1636.5 MHz. These results reveal a high power of 20 Watt, which was the design target.the design target.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.458-461
• /
• 2015

In this paper 2 types of voltage references and a current reference suitable for low-voltage, low-power circuits are proposed and designed with $0.35{\mu}m\;CMOS$ process. MOS transistors operating in weak inversion and bulk-driven technique are utilized to achieve low-voltage and low-power features. The first voltage reference consumes 1.43uA from a supply voltage of 1.2V while it has a reference voltage of 585mV and a TC(Temperature Coefficient) of $6ppm/^{\circ}C$. The second voltage reference consumes 48pW from a supply voltage of 0.3V while having a reference voltage of 172mV and a TC of $26ppm/^{\circ}C$. The current reference consumes 246nA from a supply voltage of 0.75V with a reference current of 32.6nA and a TC of $262ppm/^{\circ}C$. The performances of the designed references have been verified through simulations.

• Journal of Advanced Marine Engineering and Technology
• /
• v.37 no.5
• /
• pp.461-466
• /
• 2013

This paper examines the characteristics of butt welding joint shrinkage for shipbuilding and marine structures main plate. The shrinkage strain of butt welding joint which is caused by the process of heat input and cooling, results in the difference between dimensions of the actual parent metal and the dimensions of design. This, in turn, leads to poor quality in the production of ship blocks and reworking through period of correction brings about impediment on improvement of productivity. Through experiments on butt welding joint's shrinkage strain on large structures main plate, the deformation of welding residual stress in the form of I, Y, V was obtained. In addition, the results of experiments indicate that there is limited range of shrinkage in the range of 1 ~ 2 mm in 11t ~ 21.5t thickness and the effect of heat transfer of weld appears to be limited within 1000mm based on one side of seam line so there was limited impact of weight of parent metal on the shrinkage. Finally, it has been learned that Shrinkage margin needs to be applied differently based on groove phenomenon in the design phase in order to minimize shrinkage.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.41 no.4
• /
• pp.77-84
• /
• 2013

With the increase in occurrence frequency and severity of natural disasters due to climate changes arising from global warming, damage in the landscaping field is rising. This leads to legal disputes, and is increasing social and economic damage, too. Especially even though landscape trees which are highly affected by external environments, suffer lots of damage from natural disasters, there is no specific scope of disaster criteria and thus it brings plenty of problems of damage restoration and compensation. Therefore, this study aims to suggest that gives ways to improve related criteria for damage of landscape trees from natural disasters. For this objective, this study analyzed damage cases of landscape trees and precedents, and compared Korean and Japanese legal systems and criteria regarding natural disasters with each other. The analysis result showed that opinions of experts have a great deal of influence on judgment results, since there is no definite legal basis on damage from natural disasters in the landscaping field. This implies the need for a professional and objective appraisal process. According to the comparative analysis of Korean and Japanese legal systems and criteria regarding natural disasters, Korea lacked in laws and criteria on natural disasters of landscape plants in Korea, whereas there were concrete disaster assessment standards of landscape trees in Japan. For improving natural disaster-related systems and criteria in the landscaping field, therefore, this study presented 'Revision of related laws', 'Revision of appraisal and loss assessment criteria', 'Revision of standard specification of landscaping project', 'Compulsory insuring against disasters', 'Reasonable fulfillment of contract', and 'Compulsory cost estimation for disaster restoration', as improvement plans.

• Journal of Broadcast Engineering
• /
• v.13 no.2
• /
• pp.188-199
• /
• 2008

In conventional video coding, encoder complexity is much higher than that of decoder. However, investigations for lightweight encoder to eliminate motion prediction/compensation claiming most complexity in encoder have recently become an important issue. The Wyner-Ziv coding is one of the representative schemes for the problem and, in this scheme, since encoder generates only parity bits of a current frame without performing any type of processes extracting correlation information between frames, it has an extremely simple structure compared to conventional coding techniques. However, in Wyner-Ziv coding, channel decoding errors occur when noisy side information is used in channel decoding process. These channel decoding errors appear more frequently, especially, when there is not enough correlation between frames to generate accurate side information and, as a result, those errors look like Salt & Pepper type noise in the reconstructed frame. Since this noise severely deteriorates subjective video quality even though such noise rarely occurs, previously we proposed a computationally extremely light encoding method based on selective median filter that corrects such noise using spatial correlation of a frame. However, in the previous method, there is a problem that loss of texture from filtering may exceed gain from error correction by the filter for video sequences having complex torture. Therefore, in this paper, we propose an improved lightweight encoding method that minimizes loss of texture detail from filtering by allowing information of texture and that of noise in side information to be utilized by the selective median filter. Our experiments have verified average PSNR gain of up to 0.84dB compared to the previous method.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.9
• /
• pp.21-26
• /
• 2016

This paper presents a step-down DC-DC buck converter with a CCM/DCM dual-mode function for the internal power stage of portable electronic device. The proposed converter that is operated with a high frequency of 1 MHz consists of a power stage and a control block. The power stage has a power MOS transistor, inductor, capacitor, and feedback resistors for the control loop. The control part has a pulse width modulation (PWM) block, error amplifier, ramp generator, and oscillator. In this paper, an external capacitor for compensation has been replaced with a multiplier equivalent CMOS circuit for area reduction of integrated circuits. In addition, the circuit includes protection block, such as over voltage protection (OVP), under voltage lock out (UVLO), and thermal shutdown (TSD) block. The proposed circuit was designed and verified using a $0.18{\mu}m$ CMOS process parameter by Cadence Spectra circuit design program. The SPICE simulation results showed a peak efficiency of 94.8 %, a ripple voltage of 3.29 mV ripple, and a 1.8 V output voltage with supply voltages ranging from 2.7 to 3.3 V.