• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.14 no.5
• /
• pp.36-41
• /
• 2015

In this paper, research on the mold design of motor housing produced by the HPDC process was conducted using computer simulations and experiments. Recently, automobile parts have been required to be light and have high strength. The die casting process was used to manufacture automotive motor housings. In the die casting process, the control of casting defects is very important. However, it has usually depended on the experience of the foundry engineer. For the analysis of the manufacturing process of motor housing, the finite element method is applied. Through the simulations using commercial software, the filling pattern and product defects could be confirmed. The analysis results obtained from the filling behavior of the casting process agreed with the experimental results. The computer simulation results of filling behavior were reflected in the optimal mold design of motor housing.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.05a
• /
• pp.902-906
• /
• 2000

In end milling process the undeformed chip thickness and the cutting force components vary periodically with phase change of the tool. In this study, up end milling process is transformed to the equivalent oblique cutting. The varying undeformed chip thickness and the cutting force components in end milling process are replaced with the equivalent average ones. Then it can be possible to analyze the chip-tool friction and shear process in the shear plane of the end milling process by the equivalent oblique cutting model. According to this analysis, when cutting SM45C steel. 82% of the total energy is consumed in the shear process and the balance is consumed in the friction process.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.7 no.4
• /
• pp.56-61
• /
• 2008

Cropping metal materials is widely used for feeding processes of various forming method, such as forging, extrusion, drawing, and upsetting. However, cropping has many weak points, which are material loss in part of cutting, chip creation, and much use of lubrication oil, etc. In this study, instead of cropping, a novel process is proposed to cut metal materials, especially stainless steel bar which is known very difficult to crop. Results of FE-analysis will be shown to verify the proposed method comparing with those of the conventional cropping process. Also, fitting products were successfully forged using the fabricated billet by the proposed process.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.938-941
• /
• 2002

Small and medium enterprises have various problems that is the distributed process state, the method of receipt from custom, documentation change and so on related to the existing product design process. For that reason they require systematic analysis and smooth progress f3r each product design process. The solution is in this issue development of design management system far collaborative engineering. The aim of this system is to analyze the wrong existing process and to standardize product design process. Since this system is a server on web based Database with web identification, the client can overcome the limit of time, place and resource duplication. As a result product design process gets the greatest of efficiency in the various aspects.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.320-323
• /
• 2002

This paper discusses process design of cold forging for inner tooth part, drum clutch. In respect to high productivity, low material consumption and low piece production costs, Metal forming has more merits than machining process. Net shape forming is huh technology which satisfies merits of metal forming and achieves high accuracy. Recently, net shape forming method widely applied because of high productivity, low material consumption and low piece production costs using press. In this study, the method which accuracy of drum clutch, automatic transmission pin, can be improved is discussed. First, process variables for process design of drum clutch are selected, and then process design is accomplished using forming analysis method. from forming analysis, forming load, stress, unfiling part is obtained. and comparing these results, optimal process design can be determined.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.10
• /
• pp.103-112
• /
• 1998

The evolution of semiconductor manufacturing technology has accelerated the reduction of device dimensions and the increase of integrated circuit density. In order to improve yield within a short turn around time and maintain it at high level, a system that can rapidly determine problematic processing steps is needed. The statistical process control detects abnormal process variation of key parameters. Expert systems in SPC can serve as a valuable tool to automate the analysis and interpretation of control charts. A set of IF-THEN rules was used to formalize knowledge base of special causes. This research proposes a strategy to apply expert system to SPC in semiconductor manufacturing. In analysis, the expert system accomplishes the instability detection of process parameter, In diagnosis, an engineer is supported by process analyzer program. An example has been used to demonstrate the expert system and the process analyzer.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.8 no.3
• /
• pp.38-45
• /
• 2009

Recently, LCD Backlight Unit is being replaced from cold cathode fluorescent lamp(CCFL) to external electrode fluorescent lamp(EEFL) because the EEFL has high energy efficiency and long life. Also, it can reduce energy consumption and weight. So far, external electrode ring for EEFL is produced by sheet metal press forming process. Therefore it had low precision and much material loss. To solve these problems, Multi-Forming process that has five step forming process was invented. However, low productivity is another barrier. Product speed that is controlled by the rotational speed cannot be increased due to the unsatisfied design specification. The reason is that the gap between rolled two edge parts of the sheet plate is tightly inspected. Regarding this factor, the understanding of forming behavior to each process is inevitable. This paper describes the CAE analysis of the multi-forming process by PAM-STAMP.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.36 no.3
• /
• pp.34-42
• /
• 2013

In this study, we develop a method for analyzing business process based on the event-driven process chain (EPC) model. The method consists of five stages such as identifying abnormal events, finding causes for the abnormal events and problems caused by the abnormal events, making cause-and-effect chains, drawing root-cause map, and defining improvement areas. We illustrate how to apply the method with some examples for the domestic registered mail delivery process.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.8 no.4
• /
• pp.924-929
• /
• 2007

This paper introduces a simulation model regarding the process analysis of a LED assembly process. The objective of the simulation model is to evaluate the performance of various design aspects of process alternatives. To develop the simulation model, a time study is performed for each process. Next, by using ARENA, a simulation model is conducted based on the process analysis and the line balancing methodology. We found out several problems for the assembly process, and then suggest several alternatives to improve the system.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.71-74
• /
• 2008

In order to resolve the problems which appear after the clean large ingot production process, the impurities which are involved in the steel smelting process should be removed by developing cleaner materials. Through the rationalization of cogging process that is the first forging process of large ingot the quality is to be improved. For the sake of the optimization of an open die forging process and the improvement of the subject matter frequency ratio, a hazard precise die forging process must be developed and a Near Net Shape Forming accomplished. As a result, energy can be reduced by minimizing an after control process. In order to produce large axes and other forming parts, processing techniques are to be developed. In this context, this paper is a study about a reduction ratio, dies width ratio and rotary angles, the amount of overlap, and intends to analysis cogging processes, utilizing Deform-3D cogging module