• Journal of the Korean Society for Precision Engineering
• /
• v.24 no.5
• /
• pp.89-96
• /
• 2007

Inkjet printing has become one of the most attractive manufacturing techniques in industry. Especially inkjet printing technology will soon be part of the PCB (Printed Circuit Board) fabrication processes. Traditional printing on PCB includes screen printing and photolithography. These technologies involve high costs, time-consuming procedures and several process steps. However, by inkjet technology manufacturing time and production costs can be reduced, and procedures can be more efficient. PCB manufacturers therefore willingly accept this inkjet technology to the PCB industry, and are quickly shifting from conventional to inkjet printing. To produce the printed circuit board by the inkjet technology, it must be harmonized with conductive nano ink, printing process, system, and inkjet printhead. In this study, micro patterning of conductive line has been investigated using the piezoelectric printhead driven by a bipolar voltage signal is used to dispense 20-40 ${\mu}m$ diameter droplets and silver nano ink which consists of 1 to 50 nm silver particles that are homogeneously suspended in an organic carrier. To fabricate a conductive line used in PCB with high precision, a printed line width was calculated and compared with printing results.

• Journal of information and communication convergence engineering
• /
• v.6 no.1
• /
• pp.43-46
• /
• 2008

This paper proposes an advanced test circuit for detecting the connectivity between a drum ring of laser printer and PCB. The detection circuit of charge sharing is proposed, which minimizes the influences of internal parasitic capacitances. The test circuit is composed of precharge circuit, analog comparator, level shifter. Its functional operation is verified using $0.6{\mu}m$ 3.3V/40V CMOS process parameter by HSPICE. Access time is100ns. Layout of the drum contact test circuit is $465{\mu}m\;{\times}\;117{\mu}m$.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.1806-1809
• /
• 2008

Study that form micro pattern by direct ink jet printing method is getting attention recently. Direct ink jet printing spout fine droplet including nano metal particle by force or air pressure. There is reason which ink jet printing method is profitable especially in a various micro-patterning technology. It can embody patterns directly without complex process such as mask manufacture or screen-printing for existent lithography. In this study, research of a technology that ejects fine droplet form of Pico liter and forms metal micro pattern was carried with inkjet head of piezoelectricity drive system. Droplet established pattern while ejecting consecutively and move on the surface at the fixed speed. Patterns formed in ink are mixed with organic solvent and polymer that act as binder. So added thermal hardening process after evaporate organic solvent at isothermal after printing. I executed high frequency special quality estimation of CPW transmission line to confirm electrical property of manufactured circuit board. We tried a large area printing to confirm application possibility of an ink jet technology.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.2
• /
• pp.130-136
• /
• 2000

Generally, the build-up printed circuit board manufactured by the sequential process with etching, plating, drilling etc. requires many types of equipments and lead time. Etching process is suitable for mass production, however, it is not adequate for manufacturing prototype in the developing stage. In this study, we introduce a screen printing technology to prototyping a build-up printed circuit board. As for the material, photo/thermal curable resin and conductive paste are used for the formation of dielectric and conductor. The build-up structure is made by subsequent processes such as the formation of liquid resin thin layer, the solidification by UV/IR light, and via filling with conductive paste. By use of photo curable resin, productivity is greatly enhanced compared with thermal curable resin. Finally, the basic concept and the possibility of build-up printed circuit board prototyping are proposed in comparison with to the conventional process.

• 한국태양에너지학회:학술대회논문집
• /
• 2011.04a
• /
• pp.293-298
• /
• 2011

The most widely used method to form an electrode in industrial solar cells are screen printing. Screen printing is characterized by a relatively simple and well-known production sequence with high throughput rates. However the method is difficult to implement a fine line width of high-efficiency solar cells can not be made. The open circuit voltage(Voc) and the short circuit current density(Jsc) and fill factor(FF) need to be further improved to increase the efficiency of silicon solar cells. In this study, gravure offset printing method using the multicrystalline-silicon solar cells were fabricated. Gravure off-set printing method which can print the fine line width of finger electrode can have the ability reduce the shaded area and increase the Jsc. Moreover it can make a high aspect ratio thereby series resistance is reduced and FF is increased. Approximately $50{\mu}m$ line width with $35{\mu}m$ height was achieved. The efficiency of gravure off set was 0.7% higher compare to that of scree printing method.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.4.1-4.1
• /
• 2011

Recently, circuit printing technology has been considered as a promising alternative to conventional PCB fabrication, for it can greatly reduce the manufacturing costs. Even though printed circuit has many advantages over typical subtractive technology such as fewer processes, it has some disadvantages. The major problems are low adhesion and poor resolution. Efforts to overcome these problems have been mainly focused on ink developments with a limited success. And surface treatments showed some improvements. Therefore, various plasma treatments and primer coatings on plastic substrates have been tested. Plasma treatments using hydrocarbon gases including methane and propane improved the pattern quality of the inkjet printed circuit, which are further improved upon heating of substrate. On the other hand, there is little effect on the adhesion, which is improved only by a special primer coating. The adhesion of inkjet printed circuit has been increased more than 10 times upon treatment. As for the screen printed circuits, the overall effects are less significant since there is some organic binder in the ink. Nonetheless, the treatment has strong positive effects on pattern quality and adhesion. The adhesion of 1 kgf/cm2, which is comparable with those of the conventional PCB circuits, is possible through primer coating for both screen and inkjet printed circuits. The resulting circuit also showed good thermal, mechanical and electrical properties.

• International Journal of Precision Engineering and Manufacturing
• /
• v.4 no.4
• /
• pp.51-56
• /
• 2003

Generally, the build-up printed circuit board manufactured by a sequential process involving etching, plating, drilling, etc, which requires many types of equipments and long lead time. Etching process is suitable for mass production, however, it is not adequate for manufacturing a prototype in the development stage. In this study, we introduce a screen printing technology for prototyping a build-up printed circuit board. As for the material, photo/thermal curable resin and conductive paste are used for the formation of dielectric and conductor. The build-up structure is made by subsequent processes such as formation of a liquid resin thin layer, solidification by a UV/IR light, and via hole filling with a conductive paste. By use of photo curable resin, productivity is greatly enhanced compared with thermal curable resin. Finally, the basic concept and the possibility of build-up printed circuit board prototyping are proposed in comparison with the conventional process.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.59.2-59.2
• /
• 2011

We have demonstrated ink-jet printed indium tin oxide (ITO) and indium tin zinc oxide (IZTO) electrodes for cost-efficient organic solar cells (OSCs). By ink-jetting of crystalline ITO nano-particles and performing a rapid thermal anneal at $450^{\circ}C$, we were able to obtain directly patterned-ITO electrodes with an average transmittance of 84.14% and a sheet resistance of 202.7 Ohm/square without using a conventional photolithography process. The OSCs fabricated on the directly patterned ITO electrodes by ink-jet printing showed an open circuit voltage of 0.57 V, short circuit current of 8.47 mA/cm2, fill factor of 44%, and power conversion efficiency of 2.13%. This indicates that the ITO directly-patterned by ink-jet printing is a viable alternative to sputter-grown ITO electrodes for cost-efficient printing of OSCs due to the absence of a photolithography process for patterning and more efficient ITO material usage.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.15 no.2
• /
• pp.1-8
• /
• 2016

Generally, electrical circuits are fabricated as Printed Circuit Boards (PCBs) and mounted on the casing of the product. Additionally, this requires many other parts and some labor for assembly. Recently, molding technology has increasingly been applied to embed simple circuits in plastic casing. The technology is called a Molded Interconnected Device (MID). By using this technology, PCB fabrication can be replaced by molding, and much of the corresponding assembly process for PCBs can be eliminated if the circuit is simple enough for molding. Furthermore, as the improvement of conductive materials and printing technologies of simple electric circuits can be printed directly on the casing part, this also reduces the complexity of the product design and production cost. Therefore, this paper introduces a new MID fabrication process using direct 3D printing technology. Additionally, it is applied to an automotive part of a cruise control switch. The methodology and design are shown.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.65 no.1
• /
• pp.57-65
• /
• 2016

This paper was analyzed the characteristics of piezoelectric inkjet print head using finite element method(FEM). It showed the bending node driving of piezoelectric and relation theory principle consider piezoelectric material characteristics and ink characteristics. From such result we were had the piezoelectric head design and manufacture. It got a this head characteristics through experiment, we confirmed that proper voltage control is possible to through ink drop control experiment of piezoelectric print head. This paper was obtained the suitable ink jetting characteristics that manufacture the control circuit and piezoelectric inkjet print head. This practice product was applied to improvement of PCB electric circuit pattern by etching resist ink that PCB manufactured to complex process over traditional 6 stages can be simpled to 1 stage by inkjet printing technology.