• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.4
• /
• pp.77-82
• /
• 2017

As frequencies increase to the millimeter wave bands the cross sections of wave guides become smaller than a few millimeters, which cause sapatial problems in realization of spatial combining power amplifiers. In this paper we intented to overcome the problem by widening the width of wave guides using horn antenna principles. We designed a widened rectangular wave guide for using in spatial combining power amplifier in 60GHz ISM band(57-64GHz), and we installed Antipodal transition in the widened wave guide, and then we characterized it as a spatial combining power amplifier. For the compatibility of WR15 standard wave guide, we widened the width of WR15 to 7mm using principle of H-plane sectoral horn antenna and then installed 3 slots of back to back Antipodal transition. The designed spatial combining power amplifier showed good characteristics of return loss less than -22.4dB and insertion loss less than 0.53dB. However, as widening the width of the wave guide, additional modes such as $TE_{20}$, $TE_{30}$ in addition to $TE_{10}$ were accurred in the bandwidth of WR15, which restricted the bandwidth and widening of the width of the wave guide.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.324-325
• /
• 2014

Quantum wells infrared photodetectors (QWIPs) have been used to detect infrared radiations through the principle based on the localized stated in quantum wells (QWs) [1]. The mature III-V compound semiconductor technology used to fabricate these devices results in much lower costs, larger array sizes, higher pixel operability, and better uniformity than those achievable with competing technologies such as HgCdTe. Especially, GaAs/AlGaAs QWIPs have been extensively used for large focal plane arrays (FPAs) of infrared imaging system. However, the research efforts for increasing sensitivity and operating temperature of the QWIPs still have pursued. The modification of heterostructures [2] and the various fabrications for preventing polarization selection rule [3] were suggested. In order to enhance optical performances of the QWIPs, double barrier quantum well (DBQW) structures will be introduced as the absorption layers for the suggested QWIPs. The DBWQ structure is an adequate solution for photodetectors working in the mid-wavelength infrared (MWIR) region and broadens the responsivity spectrum [4]. In this study, InGaAs/GaAs/AlGaAs double barrier quantum well infrared photodetectors (DB-QWIPs) are successfully fabricated and characterized. The heterostructures of the InGaAs/GaAs/AlGaAs DB-QWIPs are grown by molecular beam epitaxy (MBE) system. Photoluminescence (PL) spectroscopy is used to examine the heterostructures of the InGaAs/GaAs/AlGaAs DB-QWIP. The mesa-type DB-QWIPs (Area : $2mm{\times}2mm$) are fabricated by conventional optical lithography and wet etching process and Ni/Ge/Au ohmic contacts were evaporated onto the top and bottom layers. The dark current are measured at different temperatures and the temperature and applied bias dependence of the intersubband photocurrents are studied by using Fourier transform infrared spectrometer (FTIR) system equipped with cryostat. The photovoltaic behavior of the DB-QWIPs can be observed up to 120 K due to the generated built-in electric field caused from the asymmetric heterostructures of the DB-QWIPs. The fabricated DB-QWIPs exhibit spectral photoresponses at wavelengths range from 3 to $7{\mu}m$. Grating structure formed on the window surface of the DB-QWIP will induce the enhancement of optical responses.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.25 no.5
• /
• pp.413-420
• /
• 2012

In this study, the Kernel integration scheme for 2D linear elastic direct boundary element method has been discussed on the basis of subparametric element. Usually, the isoparametric based boundary element uses same polynomial order in the both basis function and mapping function. On the other hand, the order of mapping function is lower than the order of basis function to define displacement field when the subparametric concept is used. While the logarithmic numerical integration is generally used to calculate Kernel integration as well as Cauchy principal value approach, new formulation has been derived to improve the accuracy of numerical solution by algebraic modification. The subparametric based direct boundary element has been applied to 2D elliptical partial differential equation, especially for plane stress/strain problems, to demonstrate whether the proposed algebraic expression for integration of singular Kernel function is robust and accurate. The problems including cantilever beam and square plate with a cutout have been tested since those are typical examples of simple connected and multi connected region cases. It is noted that the number of DOFs has been drastically reduced to keep same degree of accuracy in comparison with the conventional isoparametric based BEM. It is expected that the subparametric based BEM associated with singular Kernel function integration scheme may be extended to not only subparametric high order boundary element but also subparametric high order dual boundary element.

• Restorative Dentistry and Endodontics
• /
• v.25 no.3
• /
• pp.359-370
• /
• 2000

The purpose of this investigation was to observe the viscoelastic properties of five commercial flowable(Aeliteflo, Flow it, Revolution, Tetric flow, Compoglass flow), three conventional hybrid(Z-100, Z-250, P-60) and two condensable(Synergy compact, SureFil) resin composites. A dynamic oscillatory shear test was done to evaluate the storage shear modulus (G'), loss shear modulus(G"), loss tangent(tan ${\delta}$) and complex viscosity(${\eta}^*$) of the resin composites as a function of frequency - dynamic frequency sweep test from 0.01 to 100 rad/s at $25^{\circ}C$ - by using Advanced Rheometric Expansion System(ARES). To investigate the effect on the viscosity of resin composites of filler volume fraction, the filler weight % and volume % were measured by means of Archimedes' principle using a pyknometer. The results were as follows 1. The complex viscosity ${\eta}^*$ of flowable resins was lower than that of hybrid resins and significant differences were observed between brands. The complex viscosity ${\eta}^*$ of condensable resins was higher than that of hybrid resins. The order of complex viscosity ${\eta}^*$ at ${\omega}$=10 rad/s was as follows, Surefil, Synergy compact, P-60, Z-250, Z-100, Aeliteflo, Tetric flow, Compoglass flow, Flow it, Revolution. The relative complex viscosity of flowable resins compared to Z-100 was 0.04~0.56 but Surefil was 30.4 times higher than that of Z-100. 2. The storage shear modulus G' and the loss shear modulus G" of flowable resins were lower than those of hybrid resins but those of condensable resins were higher. The patterns of the change of loss tangent, tan ${\delta}$, of resin composites with increasing frequency were significantly different between brands. The phase angles, ${\delta}$, ranged from $30.2{\sim}78.1^{\circ}$ at ${\omega}$=10 rad/s. 3. All composite resins represent pseudoplastic nature with increasing shear rate. 4. The complex shear modulus $G^*$ and the phase angle ${\delta}$ was represented by the frequency domain phasor form, $G^*({\omega})=G^*e^{i{\delta}}=G^*{\angle}{\delta}$. The locus of frequency domain phasor plots in a complex plane was a valuable method that represent the viscoelastic properties of composite resins. 5. There was no direct linear correlationship but a weak positive relation was observed between filler volume % or weight % and the viscosity of the resin composites.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.25 no.4
• /
• pp.69-80
• /
• 1988

This paper proposes simple formulae for buckling and ultimate strength estimation of plates subjected to water pressure and uniaxial compression. For the construction of a formula for elastic buckling strength estimation, parametric study for actual ship plates with varying aspect ratios and the magnitude of water pressure is carried out by means of principle of minimum potential energy. Based on the results by parametric study, a new formula is approximately expressed as a continuous function of loads and aspect ratio. On the other hand, in order to get a formula for ultimate strength estimation, in-plane stress distribution of plates is investigated through large deflection analysis and total in-plane stresses are expressed as an explicit form. By applying Mises's plasticity condition, ultimate strength criterion is then derives. In the case of plates under relatively small water pressure, the results by the proposed formulae are in good agreement compared with those by other methods and experiment. But present formula overestimates the ultimate strength in the range of large water pressure. However, actual ship plates are subjected to relatively small water pressure except for the impact load due to slamming etc.. Therefore, it is considered that present formulae can be applied for the practical use.

• Journal of architectural history
• /
• v.20 no.4
• /
• pp.61-80
• /
• 2011

This study estimated the prototype of Yangjindang at the time of its foundation by putting together the literature and discovered data and historical research on family related to Sangju Yangjindang, and looked at its architectural characteristics. These are summarized as follows: First, Yangjindang is an office building which was completed in three years [1629] after its start of construction when Keomgan Jojeong was at the age of 72 [1626] in his latter days and it was used for performing ancestral rites for Jojeong's forefathers of the head family of Pungyang Jo by family origin. Yangjindang was founded as a base of utopia for putting ancestral rites & commemoration, harmoniousness of a tribe, and educational idea into practice together with Ojakdang. Such a movement can be judged to interpret and apply the circumstances of the times realistically and flexibly where they tried to pursue the promotion of Confucianism & studies of the proprieties as well as the consciousness of practice, and to bring a tribe into harmony after the war through the retirement of Toegye School. Second, it is located at a topographically ideal spot on the edge of the Jangcheon-a tributary of Nakdong with a good physiology and landscape and its location was also the lot for a house of Jojeong's ancestor, which was burned down by war. Behind such a location and planning of Yangjindang, it is presumed, though not certain that it was modelled after Naeap village at Andong- Jojeong's parents-in-low's home. Third, as for its foundation size, it's a head house as much as about more than 100-kan, and its structure is composed of Samyo, Bonche, and Yangjindang. In addition, arrangements of buildings and its composition system and renovation procedures followed Chu-tzu Garyoe. Composition of Samyo can be restored to Yangjindang, Jugo, Woesammun, and Samyo; however, there has been no case of existence in case of Jugo building composition & arrangement takes on an aspect of a compromise between Gamyojido and Sandangjido of Garoe, which seems to be the result from flexibly interpreting and applying the rituals and studies of the proprieties of Toegye School in keeping with locational topography and realistic circumstances while making it a principle for them to observe by Toegye School. There exists a difference between Bonche and its counterpart of the upper class housing at Sangju district in that Bonche[main building] is a squre-shaped 'Ttuljip' typical of Andong setting a family ancestral ritual as a main function. Fourth, there existed a lot of hardships in raising money to cover repairs in time of doing repairs to this structure after 180 years since its establishment. In case of the repair work on Bonche, the level of renovation was limited to the replacement of old materials for rafters, doorpost, roof members and railings with new materials, together with partial alterations in case of window system. It is estimated that Yangjindang was renovated in 1808, and afterwards it was renamed Okryujeong after being re-built at another site. Through the repairs, the floor was expanded for the clan's meeting, and angle rafters and roof members were mended as well. Especially, the plane and structure of Okryujeong which was re-built at another site are expected to give clues to its restoration due to the resemblance to original appearance of Yangjindang at the time of its renovation in 1808.

• Journal of the Korean Institute of Traditional Landscape Architecture
• /
• v.28 no.3
• /
• pp.72-84
• /
• 2010

This study was attempted in order to offer basic data for implementing and applying Samjonseokjo(三尊石造), which is one of traditional stone construction method, by confirming how the constructive principle is expressed such as proportional beauty, which is contained in the modeling of Triad of Buddha Carved on Rock that was formed in the period of the Three States, centering on Triad of Buddha Carved on Rock in Susan. The summarized findings are as follows. 1. As a result of analyzing size and proportion of totally 17 of Triad of Buddha Carved on Rock, the average total height in Bonjonbul(本尊佛) was 2.96m. Right Hyeopsi(右挾侍) was 2.19m. Left Hyeopsi(左挾侍) was 2.16m. The height ratio according to this was 100:75:75, thereby having shown the relationship of left-right symmetrical balance. The area ratio in left-right Hyeopsi was 13.4:13.7, thereby the two area having been evenly matched. 2. The Triad of Buddha Carved on Rock in Seosan is carved on Inam(印岩) rock after crossing over Sambulgyo bridge of the Yonghyeon valley. Left direction was measured with $S47^{\circ}E$ in an angle of direction. This is judged to target an image change and an aesthetic sense in a Buddhist statue according to direction of sunlight while blocking worshipers' dazzling. 3. As for iconic characteristics of Buddha Carved on Rock in Seosan, there is even Hyeopsi in Bangasang(半跏像) and Bongjiboju(捧持寶珠) type Bosangipsang. In the face of Samjon composition in left-right asymmetry, the unification is indicated while the same line and shape are repeated. Thus, the stably visual balance is being shown. 4. In case of Triad of Buddha Carved on Rock in Seosan, total height in Bonjonbul, left Hyeopsi, and right Hyeopsi was 2.80m, 1.66m, and 1.70m, respectively. Height ratio in left-right Hyeopsibul was 0.60:0.62, thereby having been almost equal. On the other hand, the area ratio was 28.8:25.2, thereby having shown bigger difference. The area ratio on a plane was grasped to come closer to Samjae aesthetic proportion. 5. The axial angle of centering on Gwangbae was 84:46:50, thereby having been close to right angle. On the other hand, the axial angle ratio of centering on Yeonhwajwa(蓮華坐: lotus position) was measured to be 135:25:20, thereby having shown the form of inequilateral triangle close to obtuse angle. Accordingly, the upper part and the lower part of Triad of Buddha Carved on Rock in Susan are taking the stably proportional sense in the middle of maintaining the corresponding relationship through angular proportion of inequilateral triangle in right angle and obtuse angle. 6. The distance ratio in the upper half was 0.51:0.36:0.38. On the other hand, the distance ratio in the lower half was 0.53 : 0.33 : 0.27. Thus, the up-down and left-right symmetrical balance is being formed while showing the image closer to inequilateral triangle. 7. As a result of examining relationship of Samjae-mi(三才美) targeting Triad of Buddha Carved on Rock in Susan, the angular ratio was shown to be more notable that forms the area ratio or triangular form rather than length ratio. The inequilateral triangle, which is formed centering on Gwangbae(光背) in the upper part and Yeonhwajwa(lotus position) in the lower part, is becoming very importantly internal motive of doubling the constructive beauty among Samjae, no less than the mutually height and area ratio in Samjonbul.