• Journal of the Korean institute of surface engineering
• /
• v.56 no.1
• /
• pp.69-76
• /
• 2023

The effects of hairline treatment on surface blackening and thermal diffusion behaviors of Zn-Al-Mg alloy coated steel sheet were evaluated by the three-dimensional surface profiler and laser-flash technique. The metallographic observation of coating damages by hairline treatments showed that several cracks were initiated and propagated along the interface between primary Zn/eutectic phases. As the hairline processing became more severe, the crack occurrence frequency in eutectic phase of coating layer and the surface roughness increased, which had a proportional relationship with the level of blackening on the coating surface. In addition, the higher interfacial areas of the blackened coating surface, caused by the hairline process, led to an increase in thermal diffusivity and conductivity of the coated steel sheet. On the other hand, when the coating damage by hairline treatment was excessive and the steel substrate was exposed, there was little difference between the thermal diffusivity/conductivity of the untreated sample though the blackening degree was higher than that of untreated sample. This work suggests that the increase in the surface areas of the coating layer without exposure to steel substrate through hairline treatment can be one of the effective technical strategies for the development of Zn-Al-Mg alloy coated steel sheets with higher blackening level and thermal diffusivity.

• Journal of Korea Foundry Society
• /
• v.20 no.5
• /
• pp.323-329
• /
• 2000

The HSS consists of hard carbide and matrix of martensite, and so its characteristics of wear resistance, fracture resistance, and surface roughness are good. This study was undertaken to investigate the influence of Nb and V and manufacturing conditions on microstructural behaviors and characteristics in the HSS cylindrical specimens(90 $mm^{O.D.}$ ${\times}$ 60 $mm^{I.D.}$ ${\times}$ 50 $mm^H$) manufactured using VCC(Vertical Centrifugal Casting). In the specimen of Fe-2C-6Cr-1.5W-3Mo-4V alloy, the amount of MC carbide was increased and $M_7C_3$ carbide was decreased with the increase of V and Nb contents. The primary VC carbide was formed and followed by the rod-type eutectic MC carbide was formed in the cell boundary in 9%V added specimen. MC carbide was increased, and $M_7C_3$ carbide was decreased with the addition of Nb content. In the specimen containing more than 3%Nb, primary NbC carbide was formed within the cell of matrix. With increase in rpm, cell and carbides became fine, and amount of carbide $M_7C_3$ was decreased due to increase in cooling rate.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.12 no.4
• /
• pp.197-206
• /
• 2010

The purpose of this study is to dye hanji/cotton fabrics using persimmon juice and to investigate the change in the hand fabrics. Using the Kawabata Evaluation System, we have examined the changes in the physical properties, primary hand value and total hand value. The dynamic characteristics of hanji/cotton fabrics have been explored by tensile, shear, bending, compression, surface properties, thickness and weight. As a result, it can be seen that the linearity of load-extension and tensile resilience are increased with the increase of the concentration and dyeing times of persimmon juice and tensile energy is decreased in the same condition. These behaviors are shown in the compression properties. Although the mechanism of persimmon juice dyeing has been widely discussed, it means that the fabrics dyed with persimmon juice become stiffened and the elasticity is increased with the introduction of persimmon on the fabrics studied. Bending rigidity and hysteresis of the bending moment are increased with the increase of the concentration and dyeing times of persimmon juice. Also, Geometrical roughness, expressed in SMD is increased with increasing the concentration and dyeing times of persimmon juice, compared with as-received. It indicates that these results are due to the geometric structure of hanji yarn and the introduction of persimmon juice on the fabrics studied. The fullness and softness with the soft feeing are increased a little due to the tannin component of persimmon juice introduced on the fiber surface.

• Corrosion Science and Technology
• /
• v.18 no.1
• /
• pp.1-7
• /
• 2019

To find proper lathe machining parameters for SA182 Grade 304 stainless steel (SS), six kinds of samples with different machining surface states were prepared using a lathe. Surface morphologies and microstructures of near surface deformed layers on different samples were analysed. Surface morphologies and chemical composition of oxide films formed on different samples in simulated primary water with $100{\mu}g/L\;O_2$ at $310^{\circ}C$ were characterized. Results showed that surface roughness was mainly affected by lathe feed. Surface machining caused grain refinement at the top layer. A severely deformed layer with different thicknesses formed on all samples. In addition to high defect density caused by surface deformation, phase transformation, residual stress, and strain also affected the oxidation behaviour of SA182 Grade 304 SS in the test solution. Machining parameters used for # 4 (feed, 0.15 mm/r; back engagement, 2 mm; cutting speed, 114.86 m/min) and # 6 (feed,0.20 mm/r; back engagement, 1 mm; cutting speed, 73.01 m/min) samples were found to be proper for lathe machining of SA182 Grade 304 SS.

• Fashion & Textile Research Journal
• /
• v.15 no.1
• /
• pp.156-162
• /
• 2013

For the development of high quality textiles, silk fabrics were dyed repeatedly with persimmon juice by padding mangle. We evaluated the mechanical properties and hand value by Kawabata Evaluation system for dyed silk fabrics. The results obtained from this study were as follows. With the increase of repeating padding times of dyeing, the linearity load-extension curves of the silk fabrics were increased; however, the tensile resilience of fabrics decreased. The hysteresis values of shear force were increased without significant change of shear stiffness. The coefficient of friction values were also decreased and geometrical roughness values were increased. The silk fabrics dyed with persimmon juice had shown the thickness and weight grow as the number of padding increases. The hand values of silk fabrics which were classified into 6 items in the Kawabata Evaluation System, were evaluated as repeating times of dyeing with persimmon juice. The hand values of Koshi(stiffness) and Hari(anti-drape stiffness) were increased, whereas Shinayakasa (flexibility with soft feeling) and Fukurami(fullness and softness) were decreased by dyeing with persimmon juice. However there was no significant change in hand values according to repeating padding times of dyeing.

• Proceedings of the KSRS Conference
• /
• 2002.10a
• /
• pp.734-738
• /
• 2002

We present spectral characteristics of tidal flat sediments and algal mat that were tested in the Gomso and Saemangum tidal flats, Korea. The objective of this study is to investigate the spectral reflectance and the radar scattering modeling in the tidal flats. Ground truth data obtained in the tidal flats include grain size, soil moisture content and its variation with time, surface roughness, chlorophyll, ground leveling, and field spectral reflectance measurement. The concept of an effective exposed area (EEA) is introduced to accommodate the effect of remnant surface water, and it seriously affects the reflection of short wavelength infrared and microwave. The nin size of 0.0625 mm has been normally used as a critical size of mud and sand discrimination. But we propose here that 0.25 mm is more practical grain size criterion to discriminate by remote sensing. Algal mat is the primary product in tidal flats, and it is found to be very important to understand spectral characteristics for tidal flat remote sensing. We have also conducted radar scattering modeling, and showed L-band HV-polarization would be the most effective combination.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2001.10a
• /
• pp.38-42
• /
• 2001

A complete quantitative understanding of DT has been difficult because the process represents such a broad field of research. The experimental measurement of tool force is a single area of DT which still covers a wide range of possibilities. There are numerous parameters of the process which affect cutting forces. There are also many turnable materials of current interest. To obtain information toward a better understanding of the process, a few cutting parameters and materials were selected for detail study. It was decided that free-oxygen copper and 6061-T6 alloy aluminum would be the primary test materials. There are materials which other workers have also used because of there wide use in reflective applications. The experimental phase of the research project began by designing tests to isolate certain cutting parameters. The parameters chosen to study were those that affected the cross-sectional area of the uncut chip. The specific parameters which cause this area to vary are the depth of cut and infeed per revolution, or feedrates. Other parameter such a tool nose radius and surface roughness were investigated as they became relevant to the research.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.957-960
• /
• 1997

A complete quantitative understanding of DT has been difficult because the process represents such s broad field of research. The experimental measurement of tool force is a single area of DT which still covers a wide range of possibilities. Here are numerous parameters of the process which affect cutting forces. There are also many turnable materials of current interest. To obtain information toward a better understanding of the process, a few cutting parameters and materials were selected for detail study. It was decided that free-oxygen copper and 6061-T6 alloy aluminum would be the primary test materials. There are materials which other workers have also used because of there wide use in reflective applications. The experimental phase of the research project began by designing tests to isolate certain cutting parameters. The parameters chosen to study were those that affected the cross-sectional area of the uncut chip. The specific parameters which cause this area to vary are the depth of cut and infeed per revolution, or feedrates. Other parameter such a tool nose radius and surface roughness were investigated as they became relevant to the research.

• Membrane and Water Treatment
• /
• v.11 no.4
• /
• pp.237-245
• /
• 2020

The effects of the mixed two solvents, Dimethylacetamide (DMAc) and Dimethylformamide (DMF), and Polyethylene glycol (PEG) and Polyvinylpyrrolidone (PVP) as additives on performance of Polyvinylidene fluoride (PVDF) membranes were studied. Initially, PEG200 was used as a primary additive at fixed percentage of 5% wt. PVP was then blended with PEG200 in different concentrations. PVDF and DMAc were used as polymer and solvent in the casting solutions, respectively. To control the diffusion rate of PVP in the presence of PEG200 and PVP blend, mixtures of DMAc and DMF were used as the mixed solvent in the casting solutions. Asymmetric PVDF membranes were prepared via phase inversion process in a water bath and the effects of two additives and two solvents on the membrane morphology, pure water flux (PWF), hydrophilicity and rejection (R) were investigated. Attenuated Total Reflection Fourier Transform Infrared Spectra (ATR-FTIR) analysis was used to show the residual PVP on the surface of the membranes. Atomic Force Microscopy (AFM) was utilized to determine roughness of membrane surface. The use of mixed solvents in the casting solution resulted in reduction of PVP diffusion rate and increment of PEG diffusion rate. Eventually, PWF and R values reduced, while porosity and hydrophilicity increased.

• The KSFM Journal of Fluid Machinery
• /
• v.14 no.6
• /
• pp.18-25
• /
• 2011

A boundary-layer pump with a single disk has been experimented to obtain its characteristic curve by changing the impeller of a centrifugal pump to a single disk. The primary objective to use of these types of pumps is to avoid hurting water life during transportation unnecessarily. The change of impeller should degrade the performance of pump, so we used the method to increase the roughness on the disk with sandpaper and mesh. The enhancement of shear force from the rotation of disk to the internal flow brought an augmentation of momentum transport, and the characteristics were far improved from the original single-disk pump without decreasing the survival rate of water life in the case of Pseudobagrus fulvidraco (bullhead fish). However, in the case of Artemia cyst (zooplankton), the survival rate was very degraded due to the micro scale smaller than turbulent eddy size. The result of this study could be used for the design of transportation and bio-filtering of water lying on a specific bandwidth of its scale of size.