• 한국전기전자재료학회논문지
• /
• 제32권3호
• /
• pp.256-261
• /
• 2019

The use of military lithium batteries in this field accelerates the generation of internal pressure because the active materials, lithium and the electrolyte, react to form sulfur dioxide gas. This also reduces the amount of electrolyte. In this condition, batteries can 'vent' or 'explode' especially when completely discharged. Such venting and explosion can be regarded as a safety accident, as toxic gases and shrapnel are ejected from the batteries which can harm the user. A DTaQ was carried out in 2017 as a quality problem solution project to solve this safety issue. A protection circuit was thereby developed, which included a micro controller unit (MCU) which can stop battery usage when in an over-discharging state by sensing its low-voltage condition. In 2018, this concept was expanded to lithium batteries for the remote controlled ammunition system. This paper reports results of the improved performance.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1994년도 하계학술대회 논문집 A
• /
• pp.535-538
• /
• 1994

In this paper, an isolated ZVS-PWM boost converter is proposed for single stage line conversion. For power factor correction, we used the half bridge topology at the primary side of isolation transformer permitting switching devices to operate under ZVS by using circuit parastics and operating at a fixed duty ratio near 50%. Thus the relatively continuous input current distortion and small size input filter are also achievable. The ZVS-PWM boost operation of the proposed converter can be achieved by using the boost inductor $L_f$, main switch $Q_3$, and simple auxiliary circuit at the secondary side of isolation transformer. The secondary side circuit differ from a conventional PWM boost converter by introduction a simple auxiliary circuit. The auxiliary circuit is actived only during a short switching transition time to create the ZVS condition for the main switch as that of the ZVT-PWM boost converter. With a single stage, it is possible to achieve a sinusoidal line current at unity power factor as well as the isolated 48V DC output. Comparing to the two stage schemes, overall effiency of the proposed converter is highly improved due to the effective ZVS of all devices as well as single stage power conversion. Thus, it can be operated at high switching frequency allowing use of small size input filter. Minimum voltage and current stress make it high power application possible.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제49권6호
• /
• pp.322-329
• /
• 2000

BIST(Built-in Self Test) has been considered as the most promising DFT(design-for-test) scheme for the present and future test strategy. The most serious problem in applying BIST(Built-in Self Test) into a large circuit is the excessive increase in test time. This paper is focused on this problem. We proposed a new BIST construction scheme which uses a parallel divide-and-conquer method. The circuit division is performed with respect to some internal nodes called test points. The test points are selected by considering the nodal connectivity of the circuit rather than the testability of each node. The test patterns are generated by only one linear feedback shift register(LFSR) and they are shared by all the divided circuits. Thus, the test for each divided circuit is performed in parallel. Test responses are collected from the test point as well as the primary outputs. Even though the divide-and-conquer scheme is used and test patterns are generated in one LFSR, the proposed scheme does not lose its pseudo-exhaustive property. We proposed a selection procedure to find the test points and it was implemented with C/C++ language. Several example circuits were applied to this procedure and the results showed that test time was reduced upto 1/2151 but the increase in the hardware overhead or the delay increase was not much high. Because the proposed scheme showed a tendency that the increasing rates in hardware overhead and delay overhead were less than that in test time reduction as the size of circuit increases, it is expected to be used efficiently for large circuits as VLSI and ULSI.

• 전력전자학회논문지
• /
• 제18권2호
• /
• pp.131-137
• /
• 2013

In this paper, the phase-shift full-bridge DC/DC converter with fixed-phase operation inverter is proposed. The proposed circuit consists of two full-bridge inverters which are connected in parallel. While one full-bridge inverter operates as the fixed-phase, it regulates the output voltage by adjusting the phase of the other inverter. During the normal operation period, the proposed circuit makes the less amount of conduction loss of the primary switches and secondary synchronous rectifiers, as well as the less amount of the current ripple of the output inductor, than the conventional phase-shift full-bridge DC/DC converter does. Also, it achieves high efficiency by reducing the snubber loss of the secondary synchronous rectifier. To sum up, the present inquiry analyzes the theoretical characteristics of the proposed circuit, and shows the experimental results from a prototype for 450W power supply.

• 영재교육연구
• /
• 제22권3호
• /
• pp.703-728
• /
• 2012

이 연구의 목적은 초등 과학 영재를 교수 및 평가하는 데 있어 종래의 정적 방법이 아닌 역동적 방법을 채택하여 전기회로 개념 이해 과정을 분석해 보는 것이다. 초등 과학 영재 11명을 대상으로 과학적인 전기회로 개념으로의 이해를 의도한 역동적 과학 평가를 실시하여 스캐폴딩 양상을 중심으로 변화 과정을 알아보고, 영재학생의 개념 변화 과정에서 나타나는 특징을 분석하였다. 연구 결과 첫째, 역동적 과학 평가를 통해 초등 과학영재의 개념 이해에 유용한 스캐폴딩 투입 특성을 확인하였다. 둘째, 역동적 과학 평가 전략에 의한 개념 정립이 개별 학생의 특성에 따라 다양한 방식으로 나타났다. 셋째, 전기회로 개념 이해의 각 장면에서 효과적으로 작용했던 전략을 확인할 수 있었다.

• 전기전자학회논문지
• /
• 제25권3호
• /
• pp.517-527
• /
• 2021

본 논문에서는 단일칩 마이컴을 이용한 위상변위 방식 직류-직류 전력변환기를 제안한다. 제안한 전력변환기의 1차측은 위상변위 방식에 의하여 단극성 펄스폭변조(unipolar PWM)로 동작하는 풀브리지 전력구조이며, 2차측은 4개의 다이오드로 구성된 풀브리지 전파정류기이다. 제안한 전력변환기의 제어는 단일칩 마이컴에 의해 수행되고, 그 MOSFET 스위치들은 부트스트랩 회로에 의해 구동된다. 그래서 전력변환기의 전체 시스템은 간단하다. 제안한 전력변환기는 공진회로와 저지커패시터를 이용하여 고효율을 달성한다. 본 논문에서는 먼저, 제안한 전력변환기의 전력회로의 동작을 각 동작모드를 따라 설명한다. 그리고 제안한 전력변환기의 전력회로 설계방식을 보이고 제안한 전력변환기를 동작시키는 마이컴 상의 소프트웨어 제어 알고리즘과 피드백 및 스위치 구동 회로에 관하여 간략히 설명한다. 그 후, 본 논문에서 제시한 설계와 구현방식에 의하여 설계하고 제작된 시제품 전력변환기의 실험결과를 통하여 제안한 전력변환기의 동작 특성을 입증한다. 실험결과에서 약 92% 정도의 최고 효율을 얻었다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1997년도 한국자동제어학술회의논문집; 한국전력공사 서울연수원; 17-18 Oct. 1997
• /
• pp.265-271
• /
• 1997

A bond graph modeling approach which is equivalent to a finite element method is formulated in the case of the piezoelectric thickness vibrator. This formulation suggests a new definition of the generalized displacements for a continuous system as well as the piezoelectric thickness vibrator. The newly defined coordinates are illustrated to be easily interpreted physically and easily used in analysis of the system performance. Compared to the Mason equivalent circuit model, the bond graph model offers the primary advantage of physical realizability. Compared to circuit models based on standard discrete electrical elements, the main advantage of the bond graph model is a greater physical accuracy because of the use of multiport energic elements. While results are presented here for the thickness vibrator, the modeling method presented is general in scope and can be applied to arbitrary physical systems.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제3권4호
• /
• pp.415-421
• /
• 2014

In this paper, reactorless high efficiency boost DC/DC converter for EV is proposed. In proposed converter, improves efficiency because decrease power loss when the switches are turned on/off using zero current switching (ZCS) at all switch of primary full bridge. By replacing reactance ingredients of L-C resonance circuit for ZCS with leakage inductance ingredients of high frequency transformer, it reduces system size and expense because of not add special reactor. For validity verification of proposed converter, in the paper implements simulation using PSIM and perform experiment by making 5KW DC/DC converter. In experimental results, efficiency of proposed converter conformed superiority.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 추계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.166-170
• /
• 2003

This paper presents the TTFC(Two Transistor Forward Converter) using Synchronous Rectifier of Compulsory Control-driver. The two transistor forward circuit is used to decrease voltage stress of primary side and the synchronous rectifier is used to reduce current stress of secondary side. Previous synchronous rectifier's MOSFET of TTFC have long dead time This paper presents synchronous rectifier of compulsory control-driver for minimized dead time. This paper compared with diode rectifier, self-driven synchronous rectifier and compulsory control-driver synchronous rectifier of TTFC. The principle of operation, feature and design considerations are illustrated and verified through the experiment with a 200W 100kHz MOSFET based experimental circuit.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권2호
• /
• pp.190-196
• /
• 2007

This paper presents the 3D finite element analysis of the Contact-less Power Supply(CPS) with linear servo motor. The primary, secondary self and leakage inductances of the contact-less power supply and the capacitances of a resonant circuit are calculated by the finite element analysis using current source. The voltage source is used to do accurate analysis of the characteristics of the contact-less power supply. The CPS with the linear servo motor is proposed. The characteristics analysis of the contact-less power supply considering the linear servo motor is done.