• 한국의학물리학회지:의학물리
• /
• 제20권1호
• /
• pp.7-13
• /
• 2009

본 논문은 물 흡수선량 표준에 기반하여 근접치료 선원인 $^{192}Ir$을 교정하는 것에 대한 예비적 연구를 위한 것이다. 이온함을 사용하여 물흡수선량 표준에 기반하여 근접치료 선원을 교정하기 위해선, 빔 선질 교정인자인 $k_{Q,Q_0}$가 필요하다. 본 연구에선 일차 표준을 사용하여 지정된 거리에서의 흡수선량를 측정하는 데 있어서의 현실적인 어려움 때문에 몬테칼로 전산모사와 반실험적인 방법을 통하여 $k_{Q,Q_0}$를 결정하였다. 본 연구를 위해 PTW30013 이온함 5개를 선택하였다. 포괄적 $k^{gen}_{Q,Q_0}$ 값의 경우엔 이온함간 변화가 최대 4.0%에 이른 반면, 개별적 $k^{ind}_{Q,Q_0}$ 경우엔 이온함간 변화가 최대 0.5% 이내였다. 이 결과는 물 흡수선량에 기반하여 근접치료 선원인 $^{192}Ir$을 교정시에 이온함을 왜 개별적으로 교정해야 하는지, 개별적인 교정이 얼마나 중요한 지를 보여 준다. 가까운 장래에 공기커마 세기 대신에 사용자가 근접치료 선원을 고에너지 광자빔과 전자빔의 교정에서처럼 치료에서 관심있는 물리량인 물흡수선량의 관점에서 교정할 수 있기를 희망한다.

• 열처리공학회지
• /
• 제22권1호
• /
• pp.8-15
• /
• 2009

Structural studies have been performed on precipitation hardening found in $Ni_{3}Al$ based ordered alloys using transmission electron microscopy (TEM). Tilt experiments by the weak-beam method were made to obtain some information concerning the cross slip mechanism of the superlattice dislocation. The strength of ${\gamma}'-Ni_3$(Al,Ti) increases over the temperature range of experiment by the precipitation of fine $\gamma$ particles. The peak temperature where a maximum strength was obtained shifted to higher temperature. Over the whole temperature range, the interaction between dislocation and $\gamma$ precipitates is attractive. On the temperature range of 773 K to 973 K, the dislocations in ${\gamma}'$ matrix move on (111) primary slip plane. When the applied stress is removed, the dislocations make cross slip into (010) plane, while those in $\gamma$ precipitates remain on the (111) primary slip plane. The increase of high temperature strength in ${\gamma}'-Ni_3$(Al,Ti) containing $\gamma$ precipitates is due to the restraint of cross slip of dislocations from (111) to (010) by the dispersion of disordered $\gamma$ particles.

• Structural Engineering and Mechanics
• /
• 제43권4호
• /
• pp.475-502
• /
• 2012

In this paper, the seismic analysis modeling technologies for sodium-cooled fast reactor (SFR) are presented with detailed descriptions for each structure, system and component (SSC) model. The complicated reactor system of pool type SFR, which is composed of the reactor vessel, internal structures, intermediate heat exchangers, primary pumps, core assemblies, and core support structures, is mathematically described with simple stick models which can represent fundamental frequencies of SSC. To do this, detailed finite element analyses were carried out to identify fundamental beam frequencies with consideration of fluid added mass effects caused by primary sodium coolant contained in the reactor vessel. The calculation of fluid added masses is performed by detailed finite element analyses using FAMD computer program and the results are discussed in terms of the ways to be considered in a seismic modeling. Based on the results of seismic time history analyses for both seismic isolation and non-isolation design, the functional requirements for relative deflections are discussed, and the design floor response spectra are proposed that can be used for subsystem seismic design.

• Journal of the Optical Society of Korea
• /
• 제19권1호
• /
• pp.29-37
• /
• 2015

The wavefront printer records a volume-reflection hologram as a two-dimensional array of elemental holograms from computer-generated holograms (CGHs) displayed on a spatial light modulator (SLM). The wavefront coming from the object is extracted by filtering in the spatial-frequency domain. This paper presents a method to improve color reproduction in a wavefront printer with spatial division of exposures at primary colors, by adaptive partitioning of the SLM in accordance with the color content encoded in the input CGHs, and by the controllable change of exposure times for the recording of primary colors. The method is verified with a color wavefront printer with demagnification of the object beam. The quality of reconstruction achieved by the proposed method proves its efficiency in eliminating the stripe artifacts that are superimposed on reconstructed images in conventional mosaic recording.

• Corrosion Science and Technology
• /
• 제14권6호
• /
• pp.301-312
• /
• 2015

Corrosion of zirconium fuel cladding is known to limit the lifetime and reloading cycles of fuel in nuclear reactors. Oxide layers formed on ZIRLO4^{TM}$ cladding samples, after immersion for 300-hour and 50-day in a simulated primary water chemistry condition ($360^{\circ}C$ and 20 MPa), were analyzed by using the scanning transmission electron microscopy (STEM), in-situ transmission electron microscopy (in-situ TEM) with the focused ion beam (FIB) technique, and X-ray diffraction (XRD). Both samples (immersion for 300 hours and 50 days) revealed the presence of the ZrO sub-oxide phase at the metal/oxide interface and columnar grains developed perpendicularly to the metal/oxide interface. Voids and micro-cracks were also detected near the water/oxide interface, while relatively large lateral cracks were found just above the less advanced metal/oxide interface. Equiaxed grains were mainly observed near the water/oxide interface.

• Progress in Superconductivity
• /
• 제11권2호
• /
• pp.96-99
• /
• 2010

We measured electrical shot noise in a metal-insulator-metal tunnel junction, which was made by using electron-beam lithography and double-angle evaporation technique. Since the dependence of the shot noise on bias voltage and temperature is theoretically well known, we can determine the temperature of the junction by measuring the noise as the voltage across the junction is changed. A cryogenic low noise amplifier was used to amplify the noise signal in the frequency range of 600-800 MHz, which enabled fast measurement of noise signal and thus temperature. With further study, this method could be useful for primary thermometry in cryogenic temperatures.

• 한국화재소방학회논문지
• /
• 제22권5호
• /
• pp.43-47
• /
• 2008

최근에 이차이온질량분석기(Secondary Ion Mass Spectrometry)를 이용한 1 2차 용융흔 구별에 관한 연구가 많은 관심을 끌고 있다. 동선의 깊이 분포에 따른 $^{12}C^-$, $^{63}Cu^-$, $^{18}O^-$, $^{35}Cl^-$ 이차 이온을 검출하기 위해 Cs+ 일차 이온빔을 사용하였고, 본 논문에서는 과전류에 의한 동선의 열적 확산에 대해 분석하였다. 분석결과 PVC 절연피복이 덮인 동선이 보다 더 깊이 탄소와 염소가 확산함을 보였으나, 산소는 절연피복이 덮이지 않은 동선이 더 깊이 확산된 것을 보였다.

• 한국주조공학회지
• /
• 제15권5호
• /
• pp.514-522
• /
• 1995

The microstructural evolution with isothermal stirring during semi-solid state processing of hypoeutectic Al-6.2wt%Si alloy was studied. Substructure of the individual primary solid particle in the slurry was investigated through transmission electron microscopy(TEM). Formation of subgrain boundaries on the rheocast Al-6.2wt%Si alloy is observed and the misorientation between the grains is shown typically under 2 degrees by analyzing selected area diffraction (SAD) and convergent beam electron diffraction (CBED) patterns. The existence of high angle grain boundaries are also observed in the alloy. Based upon these observations, mechanisms for the primary particles fragmentation are considered. With isothermal stirring, the dislocation density increases, and the evolution of dislocation cell structure takes place, which is interpreted as a process of achieving uniform deformation by dynamic recovery under applied shear stress.

• Imaging Science in Dentistry
• /
• 제52권3호
• /
• pp.319-326
• /
• 2022

This report presents the case of a 5-year-old boy with a hard swelling on the right side of the mandible body. An important point of this case is that the primary imaging finding was fine spicules in the inferior border of the mandible on panoramic radiography without significant changes in bone density. Cone-beam computed tomography views revealed a lytic lesion on the lingual side of the right mandibular body with the destruction of the lingual cortex and periosteal reaction from the midline to the first molar area. Careful attention to this radiographic finding in the primary stage in the absence of other significant imaging findings, particularly in children, could result in the early diagnosis of desmoplastic fibroma. Therefore, a better prognosis can be expected following early surgical treatment.

• 한국광학회지
• /
• 제32권6호
• /
• pp.314-322
• /
• 2021

일반적인 반사식 망원경은 오목 형태의 주경과 볼록 형태의 부경으로 구성되어 있다. 주경은 크기가 크지만 빛을 모아주는 특성으로 반사경의 파면오차 측정이 비교적 용이하다. 반면에 부경은 빛을 퍼트리기 때문에 주경보다 크기는 작지만 측정의 난이도는 더 높다고 할 수 있다. 특히 코시(Korsch) 형태의 망원경에서는 부경의 가운데 영역도 사용하는데 기존의 힌들(Hindle) 측정법으로는 가운데 부분을 측정할 수 없다. 본 논문에서는 크기가 큰 볼록비구면을 측정하기 위해 힌들 정합법(힌들 측정법과 정합법의 결합)을 적용하여 측정하고 이 측정에서 빠지는 가운데 영역은 일반간섭계의 구면파를 이용해 측정하여 두 결과를 합쳐 전체 형상 오차를 획득하는 방법을 제안하고자 한다. 제안한 방법으로 직경 202 mm, 곡률 반경 499 mm, 비구면상수 -4.613의 볼록 비구면의 형상 오차를 측정한 결과 19.5±1.3 nm rms로 측정되었다. 이 결과는 상용 정합 측정 장비로 측정한 결과와 0.7 nm rms의 근소한 차이를 보였고 반사경의 형상 오차가 45도 방향 비점수차를 가지는 것것도 일치하였다. 따라서 본 논문에서 제안한 방법이 볼록 비구면의 전체 영역을 정밀하게 측정하는데 유용함을 알 수 있었다.