• 한국식품과학회지
• /
• 제43권6호
• /
• pp.711-718
• /
• 2011

들깨의 가압가열 처리 중 들깨지방질의 산화정도와 토코페롤 및 폴리페놀 화합물의 분해는 들깨의 볶음 여부와 가열 조건에 따라 차이가 있었다. 가압가열 처리 중 볶은 들깨보다 생 들깨에서 지방질 산화 안정성은 높았으나, 산화방지제의 안정성은 낮았다. 또한 토코페롤보다는 폴리페놀 화합물이 들깨의 가압가열 중 지방질산화에 기여한 정도가 더 높았다. 그러므로 들깨를 들깨죽 제조에 적용할 때 폴리페놀 화합물의 농도와 안정성을 개선할 수 있는 방법을 모색함으로써 보다 높은 품질의 들깨 적용 식품을 생산하는데 도움이 될 것이다.

• 한국표면공학회지
• /
• 제47권3호
• /
• pp.109-115
• /
• 2014

High power impulse magnetron sputtering (HIPIMS), also known as the technology is called peak power density in a short period, you can get high, so high ionization sputtering rate can make. Higher ionization of sputtered species to a variety of coating materials conventional in the field of improving the characteristics and self-assisted ion thin film deposition process, which contributes to a superior being. HIPIMS at the same power, but the deposition speed is slow in comparison with DC disadvantages. Since recently as a replacement for HIPIMS modulated pulse power (MPP) has been developed. This ionization rate of the sputtered species can increase the deposition rate is lowered and at the same time to overcome the problems to be reported. The differences between the MPP and the HIPIMS is a simple single pulse with a HIPIMS whereas, MPP is 3 ms in pulse length is adjustable, with the full set of multi-pulses within the pulse period and the pulse is applied can be micro advantages. In this experiment, $In_2O_3$ : $SnO_2$ composition ratio of 9 : 1 wt% target was used, Ar : $O_2$ flow rate ratio is 4.8 to 13.0% of the rate of deposition was carried out at room temperature. Ar 40 sccm and the flow rate of $O_2$ and then fixed 2 ~ 6 sccm was compared against that. The thickness of the thin film deposition is fixed at 60 nm, when the partial pressure of oxygen at 9.1%, the specific resistance value of $4.565{\times}10^{-4}{\Omega}cm$, transmittance 86.6%, mobility $32.29cm^2/Vs$ to obtain the value.

• 한국세라믹학회지
• /
• 제20권3호
• /
• pp.211-216
• /
• 1983

This work aims at characterizing silicon grains and its compacts. In order to remove iron silicon grains were washed with 5N hydrochloride at 60-7$0^{\circ}C$ for 170 hrs, and then followed the chemical analysis by atomic absorption spectrophotometer X-ray diffraction analysis SEM observation and specific surface area determination by B. E. T. Mixtures of graded silicon particles with two or three different sizes were made into packings by mechanical vibration. The mixtures were used to make compacts with 10 mm in diameter and 70mm in length by isostatically pressing at 1, 208 kg/$cm^2$ (20 kpsi) and 4, 255kg/$cm^2$ (60 kpsi) respectively. Bulk densities of packings and compacts were measured. A slip made of magnesium nitrate solution and fine silicon particles was spray-dried and then decomposed at 30$0^{\circ}C$ for the purpose of coating the uniform layer of magnesium oxide on the surface of particles. The results obtained are as follows: (1) About two thirds of iron content could be removed from silicon by washing silicon powders with hydrochloride. (2) Uniform layer of magnesium oxide on the surface of silicon could be prepared by spray-drying suspension and by decomposing it. (3) B. E. T. specific surface area of fine silicon particles was 2, 826.753$m^3$/kg. (4) In the binary system with two sizes of 40-53$\mu\textrm{m}$ particles and <10$\mu\textrm{m}$ particles the maximum bulk density of packing was 55% of theoretical value and that of compacts made at the pressure of 4, 255 kg./$cm^2$ (60 kpsi) was 73% of theoretical value. (5) In the ternary system with three sizes the maximum bulk density of packing was 1.43 g/$cm^3$and that of compacts was 1.80g/$cm^3$which is equivalent to 77.6% of theoretical value. The composition of the closest compact was consisted of 50% of 40-53$\mu\textrm{m}$ particles 20% of 10-30$\mu\textrm{m}$ particles and 30% of <10$\mu\textrm{m}$ parti-cles.

• 한국전기전자재료학회논문지
• /
• 제13권4호
• /
• pp.349-358
• /
• 2000

Fabrication and Characterization of Bi$_{2}$/Sr$_{2}$/CaCu$_{2}$/O$_{8}$(Bi2212) superconductor thick films were fabricated successfully on C tapes by liquid reaction between Cu-free precursors of Bi$_{x}$/SrCaO/$_{y}$(x=1.2-2) and Cu tapes. Cu-free Bi-Sr-Ca-O powder mixtures were screen-printed on Cu tapes and heat-treated at 850-87$0^{\circ}C$ for several minutes in air oxygen nitrogen and low oxygen pressure. In order to obtain the optimum heat-treatment condition we studied the effect of the precursor composition the printing thickness and the heat-treatment atmosphere on the superconducting properties of Bi2212 films and the reaction mechanism. Microstructures and phases of thick films were analyzed by films and the reaction mechanism. Microstructures and phases of thick films were analyzed by optical microscope and XRD. The electric properties of superonducting films were examined by the four probe method. At heat-treatment temperature the thick films were in a partially molten state by liquid reaction between CuO of the oxidized copper tape and the precursors which were printed on Cu tapes. During the heat-treatment procedure Bi2212 superconducting particle nucleate and grow in preferred orientations.ons.s.

• 한국자기학회지
• /
• 제6권5호
• /
• pp.317-322
• /
• 1996

RF magnetron reactive sputtering 법으로 Fe-Zr-N 박막을 제작하여 열처리 온도와 질소 분압의 변화에 따른 포화자화, 보자력, 고주파에서의 투자율 그리고 열적 안정성을 조사하였다. Fe-Zr-N 박막은 비정질과 결정질의 경계 조성인 $Fe_{72-78}Zr_{7-10}N_{15-18}$의 조성범위에서 연자성을 나타내었다. 이러한 박막은 포화자속밀도 1.55 T, 1 MHz에서의 실효 투자율은 3000 이상의 연자성을 나타내고 열처리 온도 $550^{\circ}C$ 까지도 실효투자율 2500 정도의 열적 안정성을 나타내었다. X-선 회절 분석 결과 열처리에 의해서 ZrN 미결정이 석출하여 $\alpha-Fe$ 결정 성장이 억제되어 우수한 연자기적 성질이 나타난다고 판단된다. 이때 $\alpha-Fe$ 입자 크기는 $40~50\AA$, ZrN의 입자 크기는 $10~15\AA$이었다.

• 한국신뢰성학회지:신뢰성응용연구
• /
• 제15권3호
• /
• pp.197-206
• /
• 2015

Failure analysis of pre-insulated pipe (SPPS 380, 400A) transporting high temperature water ($95{\sim}110^{\circ}C$) for a plant was carried out. The damaged area (${\Phi}5mm$) of pre-insulated pipe was found only on welds. The chemical composition of damaged pipe meets specification of carbon steel pipes for pressure service (KS D 3562). As results of microstructure analysis, crack propagated from outer to inside after pitting corrosion occurred on the outside surface. The non-metallic inclusion existed on the end of crack. And the non-metallic inclusion continuously and linearly formed along with the bond line of welds. Based on SEM-EDS analysis, the nonmetallic inclusions have higher Manganese (Mn) and Oxygen (O) content but sulfur (S) was not detected. As results of water quality analysis, hydrogen ion concentration and minerals like Fe, Mg, Si were in low level. But the content of dissolved oxygen (11.2 ppm) was slightly higher than that of standard. It seems that the cause of damaged pipe is grooving corrosion due to MnO inclusion formed on bond line and corrosion took place nearby welds.

• 한국재료학회지
• /
• 제27권7호
• /
• pp.386-391
• /
• 2017

Using a customized diffusion bonder, we executed diffusion bonding for ring shaped white gold and red gold samples (inner, outer diameter, and thickness were 15.7, 18.7, and 3.0 mm, respectively) at a temperature of $780^{\circ}C$ and applied pressure of 2300 N in a vacuum of $5{\times}10^{-2}$ torr for 180 seconds. Optical microscopy, field emission scanning electron microscopy (FE-SEM), and energy-dispersive X-ray spectroscopy (EDS) were used to investigate the microstructure and compositional changes. The mechanical properties were confirmed by Vickers hardness and shear strength tests. Optical microscopy and FE-SEM confirmed the uniform bonding interface, which was without defects such as micro pores. EDS mapping analysis confirmed that each gold alloy was 14K with the intended composition; Ni and Cu was included as coloring metals in the white and red gold alloys, respectively. The effective diffusion coefficient was estimated based on EDS line scanning. Individual values of Ni and Cu were $5.0{\times}10^{-8}cm^2/s$ and $8.9{\times}10^{-8}cm^2/s$, respectively. These values were as large as those of the melting points due to the accelerated diffusion in this customized diffusion bonder. Vickers hardness results showed that the hardness values of white gold and red gold were 127.83 and 103.04, respectively, due to solid solution strengthening. In addition, the value at the interface indicated no formation of intermetallic compound around the bonding interface. From the shear strength test, the sample was found not to be destroyed at up to 100,000 gf due to the high bonding strength. Therefore, these results confirm the successful diffusion bonding of 14K white-red golds with a diffusion bonder at a low temperature of $780^{\circ}C$ and a short processing time of 180 seconds.

• 한방비만학회지
• /
• 제4권1호
• /
• pp.95-123
• /
• 2004

Objects: This study was aimed to find out correlation between life style and cardiopulmonary function and body fat. Methods: We divided two groups by the score of behavior modification therapy questionnaire. Westudied tendency of change of cardiopulmonary function and body fat for medication of Mahuang capsule by ergogenic aids and placebo with circuit training. We got the results for Exercise stress test and Segmental Bioelectrical Impedence Analysis. Results: 1. High Score Group in Behavior Modification Therapy Questionnaire significantly(p<.05) showed elevation of Lean Body Mass, Body Fat, Waist Circumference and not significantly elevation of Body Weight, But Basal Metabolic Rate was declined. Low Score Group in Behavior Modification Therapy Questionnaire significantly(p<.05) showed elevation of Waist Circumference and not significantly elevation of Body Weight and Body Fat, Lean Body Mass but decline of Basal Metabolic Rate, Waist to Hip Ratio 2. High Score Group in Behavior Modification Therapy Questionnaire significantly(p<.05) showed elevation of $VO_{2max}$ and not significantly elevation of the rest. Low Score Group in Behavior Modification Therapy Questionnaire significantly(p<.05) showed elevation of rest Heart Rate, Diastolic Blood Pressure, and not significantly elevation of the rest except for METs Conclusion: High score group in Behavior Modification Therapy Questionnaire showed significantly elevation of body composition, but had no relationship with Cardiopulmonary function

• 대한기계학회논문집
• /
• 제14권5호
• /
• pp.1337-1348
• /
• 1990

본 연구에서는 Peng-Robinson 상태 방정식을 기본으로 하여 먼저 단일 성분의 냉매에 대한 열역학적 물성치를 구한 뒤 그 정확도를 검증하고, 동일한 형태의 상태식 과 적절한 혼합 법칙을 통해 혼합냉매의 기액 평형 상태와 냉동 및 열펌프 사이클 해 석에 필요한 엔탈피와 엔트로피 등의 열역학적 물성치를 추산하고자 한다.단일 성 분의 냉매로서는 R13B1, R22, R12, R152a, R114를 택하였고, 혼합냉매로서는 앞의 단 일성분 냉매를 혼합한 것 중에서 그 기초적인 실험 자료가 아미 알려진 R13B1/R114, R22/R114, R12/R114 R152a/R114, R13B1/R152a 및 R13B1/R12를 택하였다. 이는 추후 상이한 냉매를 단일식으로 나타낼 수 있는 대응상태의 원리를 사용한 열물성 계산의 기반이 될 수 있을 것이다.

• 한국재료학회지
• /
• 제9권11호
• /
• pp.1055-1061
• /
• 1999

투명차폐재를 목적으로 Indium Tin Oxide (ITO) 투광성 박막을 제조하고 전자파 차폐특성에 대해 조사하였다. 박막은 RF magnetron co-sputtering 증착장비를 사용하여 제작하였다. RF 인가전력, Ar 및 $O_2$분압, 기판온도를 변화시키며 전기전도도와 투광성을 겸비한 박막의 조성과 구조에 관한 실험을 진행하였다. 최적의 증착조건은 $300^{\circ}C$의 기판온도, 20sccm의 아르곤 유량, 10sccm의 산소유량, 그리고 In과 Sn의 인가전력이 각각 50W와 30W일 경우였으며, 이때 얻어진 박막은 육안으로 분명할 정도의 투광성을 보였고 5.6$\times10^4$mho/m의 높은 전기전도도를 나타내었다. 이렇게 제조된 ITO 박막의 전자파 차폐효과를 차폐이론에 의해 분석하였다. 박막의 전기전도도, 두께, skin depth로부터 차폐기구(흡수손실, 반사손실, 다중반사 보정항)에 대해 고찰하였다. 계산된 차폐효과는 26dB의 값을 보여 투광성 차폐재로 ITO 박막의 사용 가능성을 제시할 수 있었다.