• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.338-338
• /
• 2007

Photo-conductive properties of CdS films deposited on glass substrates by a reactive sputtering in Ar atmosphere were characterized as a function of working pressure and the film thickness. The XRD measurements of CdS films revealed obvious (002) preferred orientation. In 300nm-thick of films, difference between dark and photo-resistance increases with increasing working pressure within the films. The films at 5 mTorr of working pressure show a dark resistance of approximately $1\;{\times}\;10^6\;{\Omega}/{\square}$ and a photo-resistance of $3\;{\times}\;10^4\;{\Omega}/{\square}$. The decrease dark- and photo-resistance of films as thickness decrease were $1.4\;{\times}\;10^6$ and $3\;{\times}\;10^4\;{\Omega}/{\square}$, respectively. CdS films deposited on glass substrates are considered tobe suitable for photo-conductivity materials in stealth radome applications.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.10a
• /
• pp.790-793
• /
• 2005

In these days, the piezoresistive material has been applied to various sensors in order to measure the change of physical quantities. But the relationship between the sensitivity of a sensor and the position and size of piezoresistor has rarely been studied. Therefore, this paper was focused on the effect of residual stress induced in piezoresistor on the distribution of resistance change ratio and supposed the feasible position of piezoresistor. The resulting are following; The tensile residual stress in the vicinity of piezoresistor decreased the value of resistance change ratio and could not effect on all the area of diaphragm but local area around the piezoresistor. Also, the piezoresistor in the diaphragm type pressure sensor with boss should fabricate in the edge of boss in order to increase the sensitivity of pressure sensor.

• Journal of Sensor Science and Technology
• /
• v.23 no.4
• /
• pp.266-271
• /
• 2014

Chemical sensors are used in various industrial facilities such high-risk and prevent the leakage of substances, important in life and environmental protection and the safe use of industry, used for management. In particular, high-temperature environments such as power generation equipment of the rotating part due to leakage generated by the various oil, power plants Shut Down, fire, work environment (exposure to various chemical solution and gas leak) and various water, air and soil pollution causes. Thus, over the long term through various channels such as crops and groundwater contamination caused by the slow, serious adverse effect on the ecosystem. In this paper, synthetic lube oil and high pressure hydraulic fluid leakage and immediately detect a new Printed Electronic implementation of technology-based film-type sensors, and its performance test. Thus, industrial accidents and environmental pollution and for early detection of problems, large accidents can be prevented. Experimental results of the synthetic lube oil and high pressure hydraulic fluid solution after the contact time depending on the experiment and the oil solution of the sensor material of the conductive porous PE resistance value by a chemical reaction could be confirmed that rapid increase. Also implemented in the film-type oil sensor electrical resistance change over time of the reaction rate and the synthetic lube oil is about 2 minutes or less, the high pressure hydraulic fluid is less than about 1 minute was. Therefore, more high-pressure hydraulic fluid such as a low volatility synthetic lube oils are the resistance change and the reaction rate was confirmed to be the slowest.

• Journal of Environmental Science International
• /
• v.20 no.1
• /
• pp.25-34
• /
• 2011

The new empirical static model was constructed on the basis of dimension analysis to predict the pressure drop according to the operating conditions. The empirical static model consists of the initial pressure drop term (${\Delta}P_{initial}$) and the dust mass number term($N_{dust}=\frac{{\omega}_0{\nu}_f}{P_{pulse}t}$), and two parameters (dust deposit resistance and exponent of dust mass number) have been estimated from experimental data. The optimum injection distance was identified in the 64 experimental data at the fixed filtration velocity and pulse pressure. The dust deposit resistance ($K_d$), one of the empirical static model parameters got the minimum value at d=0.11m, at which the total pressure drop was minimized. The exponent of dust mass number was interpreted as the elasticity of pressure drop to the dust mass number. The elasticity of the unimodal behavior had also a maximum value at d=0.11m, at which the pressure drop increased most rapidly with the dust mass number. Additionally, the correlation coefficient for the new empirical static model was 0.914.

• Journal of Electrical Engineering and Technology
• /
• v.2 no.4
• /
• pp.525-531
• /
• 2007

Ni(75 wt.%)-Cr(20 wt.%)-Al(3 wt.%)-Mn(4 wt.%)-Si(1 wt.%) alloy thin films were prepared using the DC magnetron sputtering process by varying the sputtering conditions such as power, pressure, substrate temperature, and post-deposition annealing temperature in order to fabricate a precision thin film resistor. For all the thin film resistors, sheet resistance, temperature coefficient of resistance (TCR), and crystallinity were analyzed and the effects of sputtering conditions on their properties were also investigated. The oxygen content and TCR of Ni-Cr-Al-Mn-Si resistors were decreased by increasing the sputtering pressure. Their sheet resistance, TCR, and crystallinity were enhanced by elevating the substrate temperature. In addition, the annealing of the resistor thin films in air at a temperature higher than $300^{\circ}C$ lead to a remarkable rise in their sheet resistance and TCR. This may be attributed to the improved formation of NiO layer on the surface of the resistor thin film at an elevated temperature.

• Transactions of the Korean Society of Pressure Vessels and Piping
• /
• v.14 no.1
• /
• pp.1-7
• /
• 2018

Materials in nuclear power plants can be embrittled by neutron irradiation. According to existing studies, the effect of the material property by irradiation embrittlement can be approximately simulated by cold working (pre-strain). In this study, finite element damage analysis method using the stress-modified fracture strain model is proposed to predict J-Resistance curves of irradiated SUS316 stainless steel. Experimental data of pre-strained SUS316 stainless steel material are obtained from literature and the damage model is determined by simulating the tensile and fracture toughness tests. In order to consider damage caused by the pre-strain, a pre-strain constant is newly introduced. Experimental J-Resistance curves for various degrees of pre-strain are well predicted.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.23 no.2
• /
• pp.138-144
• /
• 2014

This study investigates the air resistance due to deflector configurations of commonly used largetrucksat a driving speedof 80 km/h. Of the 6 models that are considered, the drag causedby the pressure on the front part of the trailer is largest for model 1. For model 1, the lift caused by the difference between the velocities of the upper and lower streams isgreatest amongall the models. Model 6 has the least resistance against the flow stream consideringthedrags and lifts of theflow models. Anoptimal design can be obtainedby investigating thesimulation analysis ofvarious deflector configurationsfor the upper part of largetrucks; this optimum deflector configuration will help reduce the air resistanceon large trucks.

• Journal of Fisheries and Marine Sciences Education
• /
• v.26 no.4
• /
• pp.831-837
• /
• 2014

This paper focuses on the effects of the changes in the resistance characteristics caused by the changes of the POD shape installed in the Hydrofoil vessel, using the CFD(Computational Fluid Dynamics). We input the POD sections' basic shape as the origin of the x and y axis. Then as we cut the x-axis 0 to 2 cm, and the more we cut it, the total resistance value had increased. However, we have recognized the fact that as we cut the POD section, 3 to 5 cm, the resistance value had rather decreased. Furthermore we found out the result that as the cut partition was larger; the POD cross-section would decrease, resulting in the linear decrease of the viscous force.

• International Journal of Internet, Broadcasting and Communication
• /
• v.16 no.1
• /
• pp.148-155
• /
• 2024

We are designed was to find an efficient warm-up method for resistance training for muscle hypertrophy, and 10 males with at least 3 years of resistance training experience were selected as subjects. The 75% 1RM was measured directly based on the pre-measured bench press 1RM. After that, the main experiment of 75% 1RM bench press according to the three warm-up methods was conducted one week apart, and all experiments were randomized and cross-over. Performance according to the warm-up method (3) was measured by total exercise volume, and physiological changes were determined by myocardial workload. All post-measurement data were analyzed using SPSS.22.0 and analyzed using repeated measures one-way ANOVA and contrast comparisons were made using the deviation method. The results showed that the method of gradually increasing the number of repetitions by performing the same intensity as the intensity of the main exercise in the form of muscle hypertrophy, but at submaximal repetitions, showed the highest performance.

• Journal of the Korean institute of surface engineering
• /
• v.38 no.2
• /
• pp.69-72
• /
• 2005

ITO-Al-ITO multi-layers were deposited at room temperature by RF magnetron sputtering on polyethylene terephthalate (PET). The films were deposited at various pressures of $8\times10^{-4},\;1\times10^{-3},\;4\times10^{-3},\;8\times10^{-3}\;and\;1\times10^{-2}$ Torr. A correlation between microstructure and electro-optical properties was studied. Films deposited? at low pressure have higher transmission, and lower reflectance and resistance than film deposited at high pressure. Sheet resistance, transmission, and reflectance were $141.6\Omega/\Box\;88\%\;and\;6.8\%$ resectively when the deposition pressure was $8\times10^{-4}$ torr, that was the optimum condition.