• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.5
• /
• pp.405-409
• /
• 2001

This paper describes fabrication and characteristics of metal thin-film pressure sensor for working at high temperature. The proposed pressure consists of a chrom thin-film, patterned on a Wheat stone bridge configuration, sputter-deposited onto thermally oxidized Si membranes with an aluminium interconnection layer. The fabricated pressure sensor presents a low temperature coefficient of resistance, high-sensitivity, low non-linearity and excellent temperature stability. The sensitivity is 1.097∼1.21mV/V$.$kgf/$\textrm{cm}^2$ in the temperature range of 25∼200$^{\circ}C$ and the maximum non-linearity is 0.43%FS.

• Design & Manufacturing
• /
• v.2 no.1
• /
• pp.39-43
• /
• 2008

There occur not only many problems in the injection process but also low quality productivity due to the injection conditions of various injection factors. Injection molding process factors such as molding temperature, injection pressure, flow rate and flow velocity, must be controlled properly in filling and packing phases in the injection molding process. In this study, effects of these factors on the injection molding were investigated through the flow analysis for the holding pressure affecting cooling time. Results of this study would be helpful to setting of holding pressure for optimization of forming condition in order to reduce cooling time in injection molding.

• Journal of Biomedical Engineering Research
• /
• v.5 no.1
• /
• pp.47-54
• /
• 1984

In order to research the flow in the thin wall compliant tube, this present study is attempt to measure the cross sectional area according to change of external pressure and flow by ultrasonic method different from willy used impedance technique for flow analysis about one dimensional Steads flow. The experimental results are as follows. 1) Measurement of cross sectional area ratio by ultrasonic method by comparison with experimental results of impedance technique & theoretical results were well consent. 2) Pressure difference of upstream and down stream is alwap's maximum range at 0.4 < $\alpha$ <0.5, and have no connection with changing external pressure. 3) when the external pressure is fixed and resistance is varied, Self excited oscillation occurs in the region at 0.5 < $\alpha$ <0.6, and oscillation disappear almost at R2>=1.2

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.35 no.2
• /
• pp.12-17
• /
• 2003

The effects of wet pressing and drying conditions on the disintegration and physical properties of paper were investigated in order to get the basic information on the resistance of paper for aqueous solution during converting processes. Wet pressing of unbeaten bleached softwood kraft pulp increased WRV at the range of grammage investigated. The increase of WRV with grammage at low wet pressing pressure(50 psi) was obvious, while it was not significant at higher wet pressing pressure(110 psi). The changes of WRV by drying were affected by the grammage and wet pressing pressure. The poorer disintegration of sheet, the higher wet pressing pressure and drying temperature. Although the strength properties were increased with the grammage, wet pressing pressure and drying temperature, results showed different trend from those of beaten pulp.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.456-459
• /
• 2002

This paper describes fabrication and characteristics of ceramic pressure sensor for working at high temperature. The proposed pressure sensor consists of a Ta-N thin-film, patterned on a Wheatstone bridge configuration, sputter deposited onto thermally oxidized Si membranes with an aluminium interconnection layer. The fabricated pressure sensor presents a low temperature coefficient of resistance, high sensitivity, low non-linearity and excellent temperature stability. The sensitivity is 1.097~1.21mV/$V{\cdot}kgf/cm^2$ in the temperature range of $25{\sim}200^{\circ}C$ and the maximum non-linearity is 0.43 %FS.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.9-12
• /
• 1997

The fabrication and performance of a thin film pressure sensor are described. Cu-Ni thin film strain gauges have been fabricated by RF magnetron sputtering. For all the gauges, the relative chance in resistance ΔR/R with pressure is of the order 10$^{-3}$ for the maximum pressure. The output characteristic is found to be linear over the entire Pressure range (0-30kgf/cm$^2$) and the output sensitivity is 1.6 mV/V. The maximum nonlinearity observed in output characteristics is 0.34%FS for 5V excitation and the hysteresis is less than 0.1%FS.

• Smart Structures and Systems
• /
• v.28 no.6
• /
• pp.839-853
• /
• 2021

In this paper, a novel multimode liquid metal-based pressure sensor is developed. The main body of the sensor is composed of polydimethylsiloxane (PDMS) elastomer. The structure of the sensor looks like a sandwich, in which the upper structure contains a cylindrical cavity, and the bottom structure contains a spiral microchannel, and the middle partition layer separates the upper and the bottom structures. Then, the liquid metal is injected into the top cavity and the bottom microchannel. Based on linear elastic fracture mechanics, the deformation of the microchannel cross-section is theoretically analyzed. The changes of resistance, capacitance, and inductance of the microchannel under pressure are deduced, and the corresponding theoretical models are established. The theoretical values of the pressure sensor are in good agreement with experimental data, implying that the developed theoretical model can explain the performance of the sensor well.

• Journal of the Society of Naval Architects of Korea
• /
• v.47 no.3
• /
• pp.398-409
• /
• 2010

This paper considers the numerical computation of added resistance on ships in the presence of incident waves. As a method of solution, a higher-order Rankine panel method is applied in time domain. The added resistance is evaluated by integrating the second-order pressure on the body surface. Computational results are validated by comparing with experimental data and other computational results on a hemi-sphere, a barge, Wigley hull models, and Series 60 hull, showing very fair agreements. The study is extended to the comparison between Neumann-Kelvin and double-body linearization approaches, and their differences are discussed.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.1
• /
• pp.120-126
• /
• 2010

It was known that the excellent wear resistance of hyper eutectic aluminum alloy is based on the primary Si particles which are distributed in the base metal. When the primary Si volume fraction increases, the smaller size have excellent wear resistance characteristics. However, this trend always does not match. There is no investigation result based on the materials and methods for real using parts. In this study, using the automotive parts manufacturer currently in use hyper eutectic Al alloy tensile test specimen type sample was fabricated by 350Ton high pressure die-casting machine. Then, fluidity, tensile, impact and wear resistance properties were evaluated. If the casting quality, primary Si size, fraction and distribution are similar, mechanical properties and wear resistance are equivalent.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.208-211
• /
• 2006

Flow resistance induced by each element in suction nozzle of a vacuum cleaner with a rotary fan is investigated numerically and its relation with flow-induced noise is examined. Flow resistance and vorticity in suction nozzle are calculated and it is found that they are closely related with flow-induced noise. From numerical results, it is suggested that reduction of flow resistance effectively increases all-suction performance and decreases sound pressure level of noise generated in the suction nozzle.