• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.9
• /
• pp.790-794
• /
• 2003

This paper describes the fabrication and characteristics of ceramic thin film type pressure sensors based on Ta-N strain gauges for high temperature applications. Ta-N thin-film strain gauges are deposited onto a thermally oxidized Si diaphragm by RF sputtering in an argon-nitrogen atmos[here($N_2$ gas ratio: 8%, annealing condition: 90$0^{\circ}C$, 1 hr.), patterned on a wheatstone bridge configuration, and used as pressure sensing elements with a high stability and a high gauge factor. The sensitivity is 1.097 ～ 1.21 mV/Vㆍkgf/$\textrm{cm}^2$ in the temperature range of 25 ～ 200 $^{\circ}C$ and the maximum non-linearity resistance), non-linearity than existing Si piezoresistive pressure sensors. The fabricated ceramic thin-film type pressure sensor is expected to be usefully applied as pressure and load sensors that os operable under high-temperature.

• Journal of the Society of Naval Architects of Korea
• /
• v.44 no.6
• /
• pp.666-674
• /
• 2007

It is very important to estimate static squeezing pressure distributions for lining material of sterntube after bearing at dry dock stage since the maximum squeezing pressure value can be one of the significant characteristics representing coming navigation performances of the propulsion system. Moderate oil film pressure between lining material and propulsion shaft is also essential for safe ship service. In this paper, Hertz contact theory is explained to derive static squeezing pressure. Reynolds equation simplified from Navier-Stokes equation is centrally differentiated to numerically obtain dynamic oil film pressures. New shaft alignment technology of nonlinear elastic multi-support bearing elements is also used in order to obtain external forces acting on lining material of bearing. For 300K DWT class VLCC with synthetic bush of sterntube after bearing, static squeezing pressures are calculated using derived external forces and Hertz contact theory. Optimum partial slope of the after bush is presented by parametric shaft alignment analyses. Dynamic oil film pressures are comparatively evaluated for partially bored and unbored after bush. Finally it is proved that the partial slope can drastically reduce oil film pressure during engine running.

• Electrical & Electronic Materials
• /
• v.10 no.10
• /
• pp.1022-1028
• /
• 1997

In this paper we present the construction details and output characteristics of a diaphragm-type pressure sensor with Cu-Ni(53:47) thin-film strain gauges. In order to improve the sensitivity and the temperature compensation two circumferential gauges are placed near the center of the diaphragm and two radial gauges are located near the edge. For all the gauges the relative change in resistance ΔR/R with pressure is of the order 10$^{-3}$ for the maximum pressure. The output is found to be linear over the entire pressure range(0-30kfg/cm$^2$)and the output sensitivity obtained is 1.6mV/V. The maximum nonlinearity observed in output characteristics is 0.35%FS for 5V excitation and the hysteresis is less than 0.1%FS.

• Tribology and Lubricants
• /
• v.25 no.5
• /
• pp.335-341
• /
• 2009

Elastohydrodynamic lubrication (EHL) analysis shows that film thickness is very flat in the contact area and pressure distribution is somehow similar to that of Hertzian contact pressure except the outlet region with pressure spike. These typical patterns of EHL film thickness and pressure are the cases under the steady contact conditions of applied loads and speeds. However, many engineering contacts are rather under the conditions of varying loads and contact speeds, and therefore the predictions for endurance life and performance of machine elements with steady EHL analysis are not suitable in many occasions. This study shows the differences in film thickness formation and pressure distribution between steady and transient contact conditions in several contact cases.

• Journal of the Korean institute of surface engineering
• /
• v.9 no.3
• /
• pp.5-8
• /
• 1976

In this study, a ruture strength of epoxy resin film coated on the leaking spot in waterpipe line was determined, using water pressure, without interrupting water supply. This results could be used for the sealing of water leakage in large size waterpipe lines. An experimental equation {{{{P=Kt^m~ /R^n~ (m=2, n=3.5) }} was also obtained, where P is the rupture pressure, K is constant, t is the thickness and R is the radius of the resin film. From this results, the safe쇼 thickness of the film for a domestic use was calculated with various radii against the maximum pressure.

• Tribology and Lubricants
• /
• v.2 no.1
• /
• pp.61-68
• /
• 1986

Effects of the ram-pressure on the THD-performance of pivoted pad thrust bearings are investigated experimentally. A sector-shaped tilting pad thrust bearing and a rotating disk are used. Temperature distribution on the disk surface as well as on the pad surface, distribution of the pressure generated within the fluid film, and the film thickness are measured continuously in the circumferential direction after thermal equilibrium is established. The ram-pressure is proportional to the mean pressure of oil film and to the rotational speed of the disk and affects the maximum pressure and the pressure distribution. The temperature rise on the mating surface of the disc and the pad, contacting with the oil film, is proportional to to the bearing load and the disk speed. The ram-pressure and the temperature rise on the disk surface are dominant factors that affect the THD-performance of pivoted pad thrust bearings.

• Tribology and Lubricants
• /
• v.12 no.3
• /
• pp.63-71
• /
• 1996

The connecting rod bearing, which is subjected to periodical dynamic loading, is an impoRant component of the reciprocating engine. In the operation of this bearing, significant parameters are the oil film thickness and the film pressure. Peak film pressures of 20-30 MPa are not uncommon. So the elastic deformation of the bearing housing can have a significant effect on the bearing performance. In this study, a numerical analysis of connecting rod bearing is investigated. Elastic deformation of the bearing housing is considered in the analysis. Separate hydrodynamic and structural analysis are coupled through a direct iterative process. It is shown that as the result of the elastic deformation of the bearing housing, the eccentricity ratio is increased, and the minimum value of the minimum film thickness and the maximum value of the maximum film pressure are decreased. The variations of rotational speed and cylinder pressure affect the minimum film thickness and the maximum film pressure variations of the connecting rod bearing.

• Journal of Biosystems Engineering
• /
• v.42 no.3
• /
• pp.136-146
• /
• 2017

Purpose: This paper presents an appropriate wrapping method by analyzing the pressure distribution applied to a bale surface, along with the change in pressure according to an increase in the number of film layers in rice straw bales, which account for 74% of the total bulky feed supply in Korea. Methods: A model with the shape of an actual bale was fabricated to analyze the distribution of surface pressure in bale wrapping, and the pressure was measured. Experiments were conducted to analyze the pressure using eight different layer numbers (2, 4, 6, 8 10, 12, 14, and 16 layers) at five wrapping speeds (27, 29, 31, 33, and 35 rpm). Results: The maximum pressure applied to a circular bale by the film occurred at the center of the end of the bale, whereas the minimum pressure occurred at the center of the bale side. An extreme value ratio between the minimum and maximum pressures was distributed as 8.5-56.6%, which was improved with an increase in rotation speed. The an uneven pressure distribution occurred because the number of film overlaps was 8.24-times greater at the center of the bale's end than at the center of the ba le side. At a level 5 rotation speed, the minimum pressure was $P_{LV5-M1}=0.0625{\sigma}^2+36.173{\sigma}-36.753$ ($R^2=0.9845$) at $M_1$, and the maximum pressure was $P_{LV5-M6}=5.5552{\sigma}^2+41.05{\sigma}-39.071$ at $M_2$, revealing a correlation of $R^2=0.9983$. Conclusions: To replace four layers with six layers, 2-4 layers were added only to the side of the bale, and the minimum pressure at $M_1$ was then improved from that at four layers to that at six layers, and the amount of film consumed for 4-6 layers was reduced by 84.6%.

• Journal of ILASS-Korea
• /
• v.11 no.4
• /
• pp.212-219
• /
• 2006

The initial film flow development of the high-pressure swirl spray was investigated at different injector operating conditions to analyze film flow development and to provide the input data for the modeling works. This result can be also useful to verify the previously simulated results. The initial flow conditions such as liquid film thickness, flow angle and flow divergence are obtained by visualizing the inside and near the nozzle flow with a microscopic imaging system. The visualized images are quantified using an image processing tool. From the information of liquid film thickness and flow angle, the initial axial and tangential velocity and the swirl number of the swirl spray are successfully determined at various operating conditions. The experimental results showed that the initial liquid film thickness, flow angle and flow divergence are remained constant when the injection pressure is increased. However, initial film conditions are severely changed when the fuel temperature is increased. The swirl number remained constant when the injection pressure is increased while it showed increased value at high fuel temperature condition.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.15 no.1
• /
• pp.39-44
• /
• 1986

Kacdugi fermented in the subatomospheric pressure(350mmHg) and polyethylene film package to improve the quality and to investigate the effect of fermentative control at $25^{\circ}C$. Brix degree, acidity, vitamin C content and number of total microbe and Lactobacilli was determined and also, the edible period of kacdugi was checked up by sensory assessment. The increasing rate of brix degree during kacdugi fermentation was high in the subatomospheric pressure, but decreased at the last period of fermentation as same tendency to the control, and it was preferably increased at the last period of fermentation in the polyethylene film package. However, the acidity was higher in the control than sbuatomospheric pressure but it was low in the polyethylene film package. Vitamin C content was high in the control at beginning and middle period of fermentation but high in sbuatomospheric pressure, and was low in the polyethylene film package at the last period of fermentation. The number of Lactobacilli was more in the subatomospheric pressure and polyethylene film package than the control, but it was suddenly incressed for the total microbe in the polyethylene film package at last period of fermentation. The edible periods of kacdugi by the sensory assessment of sour flavor, hardness and complex flavor was second days in the control. third days in the polyethylene film package, and fifth days in the subatomospheric pressure after soaking.