• 한국안전학회지
• /
• 제21권6호
• /
• pp.14-19
• /
• 2006

This study performed burst tests using real-scale pipe elbow containing simulated local wall-thinning to evaluate the effects of circumferential thinning angle and bending load on the failure pressure of wall-thinned elbow. The tests were carried out under the loading conditions of internal pressure and combined internal pressure and bending loads. Three circumferential thinning angles, ${\theta}/{\Pi}=0.125,\;0.25,\;0.5$, and different thinning locations, intrados and extrados, were considered. The test results showed that the failure pressure of wall-thinned elbow decreased with increasing circumferential thinning angle for both thinning locations. This tendency is different from that observed in the wall-thinned straight pipe. Also, the failure pressure of intrados wall-thinned elbow was higher than that of extrados wall-thinned elbow with the same thinning depth and equivalent thinning length. In addition, the effect of bending moment on the failure pressure was not obvious.

• 전기학회논문지
• /
• 제63권4호
• /
• pp.541-545
• /
• 2014

In this paper, the angle of the thighs that appear during walking condition to balance estimation to the left and right leg was occurred during normal walking. Get over to the limitations of gait analysis using image processing or foot pressure that was used a lot in the previous, the angle of the thigh were used for estimation of asymmetric gait. We implemented heathy five adult male to test targeting and gait and obtained cycle data from 10 times. For this research, Thigh-Angle measurement device were developed, and attached to in a position of $20^{\circ}$ for flexion and $15^{\circ}$ for extension to measure the angle of the thigh. Also, in order to verify the reliability of estimation of asymmetric gait using thigh-angle, it was compared with the result of asymmetric gait estimation using foot pressure. The results of this paper, using the thigh angle is the average of 16.84% higher than using pressure to accuracy of determine the gait imbalance.

• Applied Science and Convergence Technology
• /
• 제27권1호
• /
• pp.19-22
• /
• 2018

The ion energy and angle distributions (IEADs) in the DC magnetron sputtering systems are investigated for the variation of gas pressure using particle-in-cell simulation. Even for the condition of collisionless ion sheath at low pressure, it is possible to change the IEAD significantly with the change of gas pressure. The bombarding ions to the target with low energy and large incident angle are observed at low pressure when the sheath voltage drop is low. It is because the electron transport is hindered by the magnetic field at low pressure because of few collisions per electron gyromotion while the ions are not magnetized. Therefore, the space charge effect is the most dominant factor for the determination of IEADs in low-pressure magnetron sputtering discharges.

• Applied Science and Convergence Technology
• /
• 제27권2호
• /
• pp.26-29
• /
• 2018

The ion energy and angle distributions (IEADs) in the DC magnetron sputtering systems are investigated for the variation of gas pressure using particle-in-cell simulation. Even for the condition of collisionless ion sheath at low pressure, it is possible to change the IEAD significantly with the change of gas pressure. The bombarding ions to the target with low energy and large incident angle are observed at low pressure when the sheath voltage drop is low. It is because the electron transport is hindered by the magnetic field at low pressure because of few collisions per electron gyromotion while the ions are not magnetized. Therefore, the space charge effect is the most dominant factor for the determination of IEADs in low-pressure magnetron sputtering discharges.

• 한방재활의학과학회지
• /
• 제19권4호
• /
• pp.115-126
• /
• 2009

Objectives : The aim of this study was to evaluate whether the foot pressure distribution correlates with the lumbo-sacral curvature, and the Oswestry Disability Index in chronic low back pain patients. Methods : We measured the fore foot pressure and the rare foot pressure using the foot analyzer in 28 women subjects with chronic low back pain. The lumbo-sacral curvature and the Oswestry Disability Index(ODI) were also measured. Results : 1. Subjects with higher ODI(%) had significantly lower Fore foot pressure/Rare foot pressure ratio(F/R ratio) (p<0.01). 2. Lumbar lordotic angle and Ferguson angle were inversely related to ODI(%) (p<0.05, p<0.01). 3. Lumbar lordotic angle and Ferguson angle were positively related to F/R ratio (all p<0.05). Conclusions : Using the Foot Analyzer(FA-48S, Tech storm Inc.) we have shown that F/R ratio has significant correlation with the lumbo-sacral curvature and the Oswestry Disability Index. These result suggest that the Foot analyzer may be used in assessing back pain in chronic low back pain patients.

• 한국철도학회논문집
• /
• 제19권6호
• /
• pp.765-776
• /
• 2016

본 연구에서는 철도 교대를 위한 표준단면을 선정하고, 선정된 단면에 대하여 토압산정방법과 내부마찰각에 따른 직배면과 가상배면에 작용하는 주동토압을 비교 분석하였다. 또한, 기존토압과 개량시행쐐기법의 토압을 이용하여 내부마찰각에 따른 교대의 외적 안정성, 부재력 및 경제성을 분석하였다. 본 연구로부터 가상배면에서의 주동토압은 직배면에서의 주동토압보다 크며, 내부마찰각이 증가함에 따라 감소한다는 것을 알 수 있었다. 기존토압(Rankine, Coulomb, 시행쐐기법) 및 개량토압(개량시행쐐기법) 모두 내부마찰각이 증가함에 따라 부재력은 크게 감소하였고, 경제성은 향상되는 것으로 평가되었다.

• 한국해안·해양공학회논문집
• /
• 제29권2호
• /
• pp.67-76
• /
• 2017

본 연구에서는 케이슨 안벽의 뒷굽이 주동토압에 미치는 영향을 조사하였다. 한계해석법을 사용하여 뒷굽의 길이에 따라 벽면마찰력이 뒷굽 상부에서 발생하는 활동면의 경사각에 미치는 영향을 분석하였다. 분석결과 뒷굽의 길이가 짧을수록 내측 활동면의 경사각은 증가하나, 외측 활동면의 경사각은 일정하였다. 실제 케이슨 안벽에서 발생하는 파괴면에 작용하는 토압과 동일한 토압을 갖는 뒷굽 끝에서의 가상의 연직배면에 작용하는 토압에 대하여 뒷굽의 상대 길이-뒤채움 토사의 내부마찰각-벽면마찰각-가상의 연직배면에 작용하는 배면마찰각 등의 상관관계를 구하였다. 뒷굽이 짧을수록 케이슨 안벽에 작용하는 토압이 Rankine 토압보다는 작아지나 뒷굽의 길이를 고려하지 않은 Coulomb 토압보다는 항상 크게 나타났다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2015년도 제49회 하계 정기학술대회 초록집
• /
• pp.181.2-181.2
• /
• 2015

Sputtering is one of the most popular physical deposition methods due to their versatility and reproducibility. Synthesis of Cr thin films by DC magnetron sputtering using glancing angle deposition (GLAD) has been reported. Chromium thin films have been prepared at two different working pressure($2.0{\times}10-2$, 30, $3.3{\times}10-3torr$) on Si-wafer substrate using magnetron sputtering with glancing angle deposition (GLAD) technique. The thickness of Cr thin films on the substrate was adjusted about 1 mm. The electrical property was measured by four-point probe method. For the measurement of density in the films, an X-ray reflectivity (XRR) was carried out. The sheet resistance and column angle increased with the increase of glancing angle. However, nanohardness and density of Cr thin films decreased as the glancing angle increased. The measured density for the Cr thin films decreased from 6.1 to 3.8 g/cc as the glancing angle increased from $0^{\circ}$ to $90^{\circ}$ degree. The low density of Cr thin films is resulted from the isolated columnar structure of samples. The evolution of the isolated columnar structure was enhanced at the conditions of low sputter pressure and high glancing angle. This GLAD technique can be potentially applied to the synthesis of thin films requiring porous and uniform coating such as thin film catalysts or gas sensors.

• International Journal of Fluid Machinery and Systems
• /
• 제2권1호
• /
• pp.13-20
• /
• 2009

The effects of positively bowed blade on the aerodynamic performance of annular compressor cascades with large camber angle were experimentally investigated under different incidences. The distributions of the exit total pressure loss and secondary flow vectors of compressor cascades were analyzed. The static pressure was measured by tapping on the cascade surfaces, and the ink-trace flow visualizations were conducted. The results show that the value of the optimum bowed angle and optimum bowed height decrease because of the increased losses at the mid-span with the increase of the caber angle. The C-shape static pressure distribution along the radial direction exists on the suction surface of the straight cascade with large r camber angles. When bowed blade is applied, the larger bowed angle and larger bowed height will further enhance the accumulation of the low-energy fluid at the mid-span, thus deteriorate the flow behavior. Under $60^{\circ}$ camber angle, flow behavior near the end-wall region of some bowed cascades even deteriorates instead of improving because the blockage of the separated flow near the mid-span keeps the low-energy fluid near the end-walls from moving towards the mid-span region, and as a result, a rapid augmentation of the total loss is easy to take place under large bowed angle. With the increase of camber angle, the choice range of bowed angle corresponding to the best performance in different incidences become narrower.

• 한국정밀공학회지
• /
• 제22권4호
• /
• pp.159-166
• /
• 2005

This study deals with the correction of gear tooth profile error by finish roll forming. First, we experimentally confirmed that the tooth profile error is a synthesis of the concave error and the pressure angle error. Since various types of tooth profile errors appear in the experiments, we introduced evaluation parameters for rolling gears to objectively evaluate profile quality. Using these evaluation parameters, we clarified the relationship among the tooth profile error, the addendum modification factor (A. M. factor), and the tool loading force. We verified the character of concave error, pressure angle error, tool loading force and number of cycles of finish roll forming by using a forced displacement method. This study makes clear that tool loading force and number of cycles of finish roll forming are very important factors that affect involute tooth profile error. The results of the experiment and analysis show that the proposed method reduces concave and pressure angle errors.