• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.386-391
• /
• 2001

This paper presents a new two-point approximation method based on the exponential intervening variable. To avoid the lack of definition of the conventional exponential intervening variables due to zero- or negative-valued design variables the shifting level into each exponential intervening variable is introduced. Then a new quadratic approximation, whose Hessian matrix has only diagonal elements of different values, is proposed in terms of these intervening variables. These diagonal elements are computed in a closed form, which correct the typical error in the approximate gradient of the TANA series due to the lack of definition of exponential type intervening variables and their incomplete second-order terms. Also, a correction coefficient is multiplied to the pre-determined quadratic term to match the value of approximate function with that of the original function at the previous point. Finally, the authors developed a sequential approximate optimizer, solved several typical design problems used in the literature and compared these optimization results with those of TANA-3. These comparisons show that the proposed method gives more efficient and reliable results than TANA-3.

• 센서학회지
• /
• 제16권1호
• /
• pp.68-76
• /
• 2007

In general, the braking system of a high speed train has an important role for the safety of the train. To stop safely the train at its pre-decided position, it is necessary to properly combine the various brakes. The train has adopted a combined electrical and mechanical (friction) braking systems. In order to design a good brake system, it is essential for designers to predict the brake performance. In this paper, the braking performance analysis program has been developed and verified by comparing the simulation results with the brake test results of HSR-350x; both results match very well. Also, the brake performances of high speed trains can be predicted by using this program under various conditions.

• 한국지능시스템학회논문지
• /
• 제11권7호
• /
• pp.621-627
• /
• 2001

In this paper, a novel and efficient global intelligent digital redesign technique for a Takagi-Sugeno (TS) fuzzy system is addressed. The proposed method should be notably discriminated from the previous works in that in allows us to globally match the states of the closed-loop TS fuzzy system with the pre-designed continuous-time fuzzy-model-based controller and those with the digitally redesigned fuzzy-model-based controller, and further to guarantee the stabilizability by the redesigned controller in the sense of Lyapunov. Sufficient conditions for the global state-matching and the stability of the digitally controller system are formulated in terns of linear matrix inequalities (LMIs). The Duffing-like chaotic oscillator is simulated and demonstrated, to validate the effectiveness of the proposed digital redesign technique, which implies the safe applicability to the digital control system.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2000년도 THE THIRD INTERNATIONAL CONFERENCE ON AGRICULTURAL MACHINERY ENGINEERING. V.II
• /
• pp.279-286
• /
• 2000

The objective of this research is to detect the papaya fruits on tree in an orchard. The detection of papaya on natural background is difficult because colors of fruits and background such as leaves are similarly green. We cannot separate it from leaves by color information. Therefore, this research will use shape information instead. First, we detect an interested object by detecting its boundary using edge detection technique. However, the edge detection will detect every objects boundary in the image. Therefore, shape description technique will be used to describe which one is the interested object boundary. The good shape description should be invariant in scaling, rotating, and translating. The successful concept is to use Fourier series, which is called "Fourier Descriptors". Elliptic Fourier Descriptors can completely represent any shape, which is selected to describe the shape of papaya. From the edge detection image, it takes a long time to match every boundary directly. The pre-processing task will reduce non-papaya edge to speed up matching time. The deformable template is used to optimize the matching. Then, clustering the similar shapes by the distance between each centroid, papaya can be completely detected from the background.

• Journal of Mechanical Science and Technology
• /
• 제15권9호
• /
• pp.1257-1267
• /
• 2001

For efficient mechanical system optimization, a new two-point approximation method is presented. Unlike the conventional two-point approximation methods such as TPEA, TANA, TANA-1, TANA-2 and TANA-3, this introduces the shifting level into each exponential intervening variable to avoid the lack of definition of the conventional exponential intervening variables due to zero-or negative-valued design variables. Then a new quadratic approximation whose Hessian matrix has only diagonal elements of different values is proposed in terms of these shifted exponential intervening variables. These diagonal elements are determined in a closed form that corrects the typical error in the approximate gradient of the TANA series due to the lack of definition of exponential type intervening variables and their incomplete second-order terms. Also, a correction coefficient is multiplied to the pre-determined quadratic term to match the value of approximate function with that of the previous point. Finally, in order to show the numerical performance of the proposed method, a sequential approximate optimizer is developed and applied to solve six typical design problems. These optimization results are compared with those of TANA-3. These comparisons show that the proposed method gives more efficient and reliable results than TANA-3.

• Structural Engineering and Mechanics
• /
• 제37권3호
• /
• pp.331-349
• /
• 2011

This study investigates the use of a vibration correlation technique (VCT) to identify the buckling load of a rectangular thin plate. It is proposed that the buckling load can be determined experimentally using the natural frequencies of plates under tensile loading. A set of rectangular plates was tested for natural frequencies using an impact test method. Aluminum and stainless steel specimens with CCCC, CCCF and CFCF boundary conditions were included in the experiment. The measured buckling load was determined from the plot of the square of a measured natural frequency versus an in-plane load. The buckling loads from the measured vibration data match the numerical solutions very well. For specimens with well-defined boundary conditions, the average percentage difference between buckling loads from VCT and numerical solutions is -0.18% with a standard deviation of 5.05%. The proposed technique using vibration data in the tensile loading region has proven to be an accurate and reliable method which might be used to identify the buckling load of plates. Unlike other static methods, this correlation approach does not require drawing lines in the pre-buckling and post-buckling regions; thus, bias in data interpretation is avoided.

• 대한기계학회논문집A
• /
• 제25권9호
• /
• pp.1423-1431
• /
• 2001

Based on the exponential intervening variable, a new two-point approximation method is presented. This introduces the shifting level into each exponential intervening variable to avoid the lack of def inition of the conventional exponential intervening variables due to zero-or negative-valued design variables. Then a new quadratic approximation whose Hessian matrix has only diagonal elements of different values is proposed in terms of these intervening variables. These diagonal elements are determined in a closed form that corrects the typical error in the approximate gradient of the TANA series due to the lack of definition of exponential type intervening variables and their incomplete second-order terms. Also, a correction coefficient is multiplied to the pre-determined quadratic term to match the value of approximate function with that of the previous point. Finally, in order to show the numerical performance of the proposed method, a sequential approximate optimizer is developed and applied to solve six typical design problems. These optimization results are compared with those of TANA-3. These comparisons show that the proposed method gives more efficient and reliable results than TANA-3.

• Journal of Forest and Environmental Science
• /
• 제29권2호
• /
• pp.131-137
• /
• 2013

This study attempts to classify forest species using hyperspectral data for supporting resources management. The primary dataset used was AISA sensor. The sensor was mounted onboard the NOMAD GAF-27 aircraft at 2,000 m altitude creating a 2 m spatial resolution on the ground. Pre-processing was carried out with CALIGEO software, which automatically corrects for both geometric and radiometric distortions of the raw image data. The radiance data set was then converted to at-sensor reflectance derived from the FODIS sensor. Spectral Angle Mapper (SAM) technique was used for image classification. The spectra libraries for tree species were established after confirming the appropriate match between field spectra and pixel spectra. Results showed that the highest spectral signature in NIR range were Kembang Semangkok (Scaphium macropodum), followed by Meranti Sarang Punai (Shorea parvifolia) and Chengal (Neobalanocarpus hemii). Meanwhile, the lowest spectral response were Kasai (Pometia pinnata), Kelat (Eugenia spp.) and Merawan (Hopea beccariana), respectively. The overall accuracy obtained was 79%. Although the accuracy of SAM techniques is below the expectation level, SAM classifier was able to classify tropical tree species. In future it is believe that the most effective way of ground data collection is to use the ground object that has the strongest response to sensor for more significant tree signatures.

• 한국건축시공학회지
• /
• 제2권4호
• /
• pp.131-135
• /
• 2002

The purpose of this study was to Identification the Risk of construction method to protect and reduce the risk of construction period. For this study we are using the pre and during construction period Inspection list. The inspection list was used by construction company for check a flaw of Construction field. So we rearrange the individual item of inspection list to match the Risk factor. This inspection list usually has the difference of importance because this list is not made by Method which is not focused on Method. Therefore, To find the difference of these importance, We surveyed this matter by doing interview of specialist group. To find the application of field and the possibility of measurement of Risk status, We tested Risk occurring frequency and it's strength by checking the level of Risk. The results of this study were as follows; Each Method Check List made out through the rearrangement of Construction Inspection list which used in construction company. To solve and compensate the matter which happened by changing the each Method Check List to each General Inspection List, we added the each Method Check List by checking the importance of check list of each process. By doing this, The Check List for finding Risk level of Method was created by using the check list of each Method.

• 한국지능시스템학회논문지
• /
• 제25권2호
• /
• pp.139-146
• /
• 2015

본 논문에서는 교정 제어에 의한 스위칭 비동기 순차 머신의 모델 정합 문제를 다룬다. 스위칭 비동기 순차 머신은 스위칭 신호에 따라서 여러 개의 비동기 순차 머신 특성을 번갈아 가면서 가지는 시스템이라고 정의한다. 이번 연구에서 스위칭 시스템이 가질 수 있는 스위칭 시퀀스(sequence)는 일정하게 고정되어 있다고 가정한다. 제어 목적은 폐루프 시스템의 안정 상태 동작을 주어진 기준 모델과 일치시키는 교정 제어기의 존재조건을 규명하고 제어기를 설계하는 일이다. 이를 위해서 스위칭 비동기 머신이 가지는 도달가능성을 표현하는 새로운 skeleton 행렬을 도입하고 모델 정합 교정 제어기의 존재조건을 기술한다. 또한 사례 연구를 통해 스위칭 신호를 생성하면서 동시에 교정 제어 입력을 변화시키는 새로운 교정 제어 알고리듬을 예시한다.