DOI QR코드

DOI QR Code

Experimental determination of the buckling load of rectangular plates using vibration correlation technique

  • Singhatanadgid, Pairod (Department of Mechanical Engineering, Faculty of Engineering, Chulalongkorn University) ;
  • Sukajit, Padol (Department of Mechanical Engineering, Faculty of Engineering, Chulalongkorn University)
  • Received : 2009.09.23
  • Accepted : 2010.10.14
  • Published : 2011.02.10

Abstract

This study investigates the use of a vibration correlation technique (VCT) to identify the buckling load of a rectangular thin plate. It is proposed that the buckling load can be determined experimentally using the natural frequencies of plates under tensile loading. A set of rectangular plates was tested for natural frequencies using an impact test method. Aluminum and stainless steel specimens with CCCC, CCCF and CFCF boundary conditions were included in the experiment. The measured buckling load was determined from the plot of the square of a measured natural frequency versus an in-plane load. The buckling loads from the measured vibration data match the numerical solutions very well. For specimens with well-defined boundary conditions, the average percentage difference between buckling loads from VCT and numerical solutions is -0.18% with a standard deviation of 5.05%. The proposed technique using vibration data in the tensile loading region has proven to be an accurate and reliable method which might be used to identify the buckling load of plates. Unlike other static methods, this correlation approach does not require drawing lines in the pre-buckling and post-buckling regions; thus, bias in data interpretation is avoided.

Keywords

References

  1. Avitabile, P. (2001), "Experimental modal analysis: a simple non-mathematical presentation", J. Sound Vib., 35(1), 20-31.
  2. Aydogdu, M. and Timarci, T. (2003), "Vibration analysis of cross-ply laminated square plates with general boundary conditions", Compos. Sci. Tech., 63(7), 1061-1070. https://doi.org/10.1016/S0266-3538(03)00016-2
  3. Chai, G.B., Banks, W.M. and Rhodes, J. (1991), "An experimental study on laminated panels in compression", Compos. Struct., 19(1), 67-87. https://doi.org/10.1016/0263-8223(91)90075-A
  4. Chailleux, A., Hans, Y. and Verchery, G. (1975), "Experimental study of the buckling of laminated composite columns and plates", Int. J. Mech. Sci., 17, 489-498. https://doi.org/10.1016/0020-7403(75)90013-2
  5. Ding, Z. (1996), "Natural frequencies of rectangular plates using a set of static beam functions in Rayleigh-Ritz method", J. Sound Vib., 189(1), 81-87. https://doi.org/10.1006/jsvi.1996.0006
  6. Go, C.G., Lin, Y.S. and Khor, E.H. (1997), "Experimental determination of the buckling load of a straight structural member by using dynamic parameters", J. Sound Vib., 205(3), 257-264. https://doi.org/10.1006/jsvi.1995.1047
  7. Go, C.G. and Liou, C.D. (2000), "Experimental determination of the buckling load of a flat plate by the use of dynamic parameters", Struct. Eng. Mech., 9(5), 483-490. https://doi.org/10.12989/sem.2000.9.5.483
  8. Lee, J.M., Chung, J.H. and Chung, T.Y. (1997), "Free vibration analysis of symmetrically laminated composite rectangular plates", J. Sound Vib., 199(1), 71-85. https://doi.org/10.1006/jsvi.1996.0653
  9. Lurie, H. and Monica, S. (1952), "Lateral vibrations as related to structural stability", J. Appl. Mech., 19, 195-204.
  10. Ni, Q.Q., Xie, J. and Iwamoto, M. (2005), "Buckling analysis of laminated composite plates with arbitrary edge supports", Compos. Struct., 69(2), 209-217. https://doi.org/10.1016/j.compstruct.2004.06.012
  11. Rajalingham, C., Bhat, R.B. and Xistris, G.D. (1996), "Vibration of rectangular plates using plate characteristic functions as shape functions in the Rayleigh-Ritz method", J. Sound Vib., 193(2), 497-509. https://doi.org/10.1006/jsvi.1996.0298
  12. Segall, A. and Springer, G.S. (1986), "A dynamic method for measuring the critical loads of elastic flat plates", Exp. Mech., 26(4), 354-359. https://doi.org/10.1007/BF02320151
  13. Singer, J., Arbocz, J. and Weller, T. (1992), Buckling Experiments: Experimental Methods in Buckling of Thinwalled Structures, Vol. 1, John Wiley & Sons, Chichester, UK.
  14. Singhatanadgid, P. and Sukajit, P. (2008), "Determination of buckling load of rectangular plates using measured vibration data", Proceedings of the International Conference on Experimental Mechanics, Nanjing, China, November.
  15. Souza, M.A. and Assaid, L.M.B. (1991), "A new technique for the prediction of buckling loads from nondestructive vibration tests", Exp. Mech., 31(2), 93-97. https://doi.org/10.1007/BF02327558
  16. Timarci, T. and Aydogdu, M. (2005), "Buckling of symmetric cross-ply square plates with various boundary conditions", Compos. Struct., 68(4), 381-389. https://doi.org/10.1016/j.compstruct.2004.04.003
  17. Tuttle, M., Singhatanadgid, P. and Hinds, G. (1999), "Buckling of composite panels subjected to biaxial loading", Exp. Mech., 39(3), 191-201. https://doi.org/10.1007/BF02323552
  18. Wang, G., Wereley, N.M. and Chang, D.C. (2005), "Analysis of bending vibration of rectangular plates using two-dimensional plate modes", J. Aircraft, 42(2), 542-550. https://doi.org/10.2514/1.4303

Cited by

  1. A note on buckling and vibration of clamped orthotropic plates under in-plane loads vol.39, pp.1, 2011, https://doi.org/10.12989/sem.2011.39.1.115
  2. Buckling analysis in hybrid cross-ply composite laminates on elastic foundation using the two variable refined plate theory vol.55, pp.1, 2015, https://doi.org/10.12989/sem.2015.55.1.047
  3. Impact of Geometrical Imperfections on Estimation of Buckling and Limit Loads in a Silo Segment Using the Vibration Correlation Technique vol.14, pp.3, 2021, https://doi.org/10.3390/ma14030567