• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.12
• /
• pp.55-67
• /
• 2010

The electrical properties of a back drilled via-hole (BDH) without the open-stub and the plated through via-hole (PTH) with the open-stub, which is called the conventional structure, in a high-count multi~layered (HCML) printed circuit board (PCB) were investigated for a high-speed digital system, and a selected inner layer to transmit a high-speed signal was farthest away from the side to mount the component. Within 10 GHz of the broadband frequency, a design of experiment (DOE) methodology was carried out with three cause factors of each via-hole structure, which were the distance between the via-holes, the dimensions of drilling pad and the anti-pad in the ground plane, and then the relation between cause and result factors which were the maximum return loss, the half-power frequency, and the minimum insertion loss was analyzed. Subsequently, the empirical formulae resulting in a macro model were extracted and compared with the experiment results. Even, out of the cause range, the calculated results obtained from the macro model can be also matched with the measured results within 5 % of the error.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.8
• /
• pp.1581-1586
• /
• 2012

In this paper, a novel resonator using ring type DGS is proposed for improvement of phase noise characteristics that is weak point of oscillator using planar type microstrip line resonator, and oscillator for 5.8GHz band is designed using proposed DGS resonator. The ring type DGS resonator is composed of DGS cell etched on ground plane under $50{\Omega}$ microstrip line. At the fundamental frequency of 5.8GHz, 7.6dBm output power and -82.7 dBc@100kHz phase noise have been measured for oscillator with ring type DGS resonator. The phase noise characteristics of oscillator is improved about 9.5dB compared to one using the general ${\lambda}/4$ microstrip resonator. Because it is possible that varactor diode or lumped capacitor is placed on the gaps of ring type DGS, resonant frequency can be controlled by bias voltage. We can design voltage controlled oscillator using proposed ring type DGS resonator. Thus, due to its simple fabrication process and planar type, it is expected that the technique in this paper can be widely used for low phase noise oscillators for both MIC and MMIC applications.

• Journal of electromagnetic engineering and science
• /
• v.13 no.3
• /
• pp.178-185
• /
• 2013

This paper introduces a high-efficiency, high-gain, broadband quasi-Yagi antenna, and its four-element array for use in 60-GHz wireless communications. The antenna was fed by a microstrip-to-slotline transition consisting of a curved microstripline and a circular slot to allow broadband characteristics. A corrugated ground plane was employed as a reflector to improve the gains in the low-frequency region of the operation bandwidth, and consequently, to reduce variation. The single antenna yielded an impedance bandwidth of 49 to 69 GHz for $|S_{11}|$ <-10dB and a gain of >12.0 dBi while the array exhibited a bandwidth of 52 to 68 GHz and a gain greater than 15.0 dBi. Both proposed designs had small gain variations (${\pm}0.5$ dBi) and high radiation efficiency (>95%) in the 60-GHz bands. The features of the proposed antenna were validated by designing, fabricating, and testing a scaled-up configuration of the single antenna at the 15-GHz band. The measurements resulted in an impedance bandwidth of 13.0 to 17.5 GHz for $|S_{11}|$ <-10dB, a gain of 10.1 to 13.2 dBi, and radiation efficiency in excess of 88% within this bandwidth. Additionally, the 15-GHz antenna yielded quite symmetric radiation profiles in both E- and H-planes, with a high front-to-back ratio.

• Journal of Advanced Navigation Technology
• /
• v.16 no.5
• /
• pp.766-772
• /
• 2012

In the present study, wideband microstrip monopole slot antennas which can be applied to the RF4CE Zigbee remote controller are designed. First I-shaped monopole slot antenna which has ${\lambda}g/4$ length at 2.45GHz is designed. In particular, a conducting via is used to connect the microstrip feed line and the ground plane surrounded with the etched slot for the bandwidth improvement. In order to reduce the antenna size, it is changed into L-shaped and T-shaped monopole slot antennas for which improve results of antenna performance are observed. In case of T-shaped monopole slot antenna, impedance bandwidth(VSWR<2) is about 3.32GHz, and also its radiation efficiency and gain is more than 90% and 2.1dBi respectively at whole operating frequency range. In particular, all of proposed monopole slot antennas have the end-fire radiations which has a maximum radiation power toward direction of open ends of monopole slots.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.5
• /
• pp.439-446
• /
• 2016

The characteristics of bearingless main rotor of helicopter are investigated through non-rotating tests and rotating tests. The stiffness and natural frequencies of rotor blades, flexbeam, and torque tube which are core components of baearingless rotor are measured to obtain input material properties for rotor analysis. The functional test on ground for assembly of one hub with damper, snubber, and no blade is carried out to check interfaces between components, kinematics of components, and pitch motion ranges under applied loads including centrifugal load. The 4-bladed bearingless rotor with 5.82m of rotor radius is tested on the whirl tower with rotation plane of 9.65m height. The thrust and power are measured to obtain hover performance and the frequencies and dampings of the rotor are obtained by excitation of cyclic pitch by hydraulic actuators.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.2
• /
• pp.137-148
• /
• 2014

In this paper, design of a UWB MIMO antenna for an on-body application is proposed and antenna performance with body effect and the impact on the human body are investigated. The proposed MIMO antenna is composed of UWB antenna above ground plane and an additional plunger shaped isolator located between the two monopole antennas to enhance the isolation characteristic. The simulation and measurement are performed to analyze the effect of the human body on antenna performance when the human body is located in the near field of the antenna. According to the measurement results, the measured SAR values for antennas 1 and 2 are 0.132 W/kg and 0.08 W/kg, respectively when 0.5 mW input power is delivered. These values satisfy the FCC guideline which ragulates that the 1-g average SAR should be lower than 1.6 W/kg.

• The Journal of Engineering Geology
• /
• v.1 no.1
• /
• pp.121-136
• /
• 1991

The focal mechanism of the Hongsung Earthquake (1978. Oct. 7, M$_L$=5.0, Latitude 36.62N, Longitude 1 26.67E) was evaulated using the polarity distribution of the P-Waveforms. Through the non-linear computer process, the compatibility of polarity distributions of the 9 P-Waveforms observed at teleseismic distances from the Hongsung Earthquake epicenter was investigated to those of the focal mechanism determined from the varying strike, dip and rake angles. The resultant values for the strike and dip angle of the principal fault plane, which apparently matches very well the sunface lineament of the Hongsung region, are determined to be about 247 degree and 78 degree with uncertainties, respectively. However, the rake angle of the focal mechanism has wide range of 40 degree to 160 degree, which is mainly due to the poor coverage of the azimuthal angle of the observed seismic stations. Due to the consistency of principal stress axes, the resultant focal mechanism could support the current stress regime of that region, which may be caused by subduction of the Pacific Plate under the Eurasia Plate along the Japan Trench. It also provides information of seismic source characteristics of the part of the Korean Peninsula for aseismic design criteria such as Site Specific Response Spectrum and Strong Ground Motion Time History for the nuclear power plants and related nuclear waste disposal facility sites.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.10
• /
• pp.2052-2058
• /
• 2009

As the operating frequency of digital system increases and voltage swing decreases, an accurate and high speed analysis of PCB board becomes very important. Transmission matrix method, which use the multiple products of unit column matrix, is the highest speedy method in PCB board analysis. In this paper a new method to reduce the calculation time of PCB board impedances is proposed. First, in this method the eigenvalue and eigenvectors of the transmission matrix for unit column of PCB are calculated and the transmission matrix for the unit column is transformed using similarity transform to reduce the number of multiplication on the matrix elements. This method using the similarity transform can reduce the calculation time greatly comparing the previous method. The proposed method is applied to the 1.3 inch by 1.9 inch board and shows about 10 times reduction of calculation time. This method can be applied to the PCB design which needs a lots of repetitive calculation of board impedances.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.9
• /
• pp.921-932
• /
• 2010

This paper presents a dual-band array antenna based on a modified Sierpinski fractal structure. Array structure is mirror symmetric, and forms broadside radiation pattern for dual frequency band if the ports are fed with $180^{\circ}C$ phase difference between upper and lower $2{\times}1$ array. To use in-phase corporate feeding circuit, the phase inversion structure is designed by changing the position of patch and ground for upper and lower array. The dimensions of the array antenna is $28{\times}30{\times}5\;cm^3$ and the bandwidth of 855~1,380 MHz(47 %), 1,770~2,330 MHz(27 %) were achieved for -10 dB return loss. The measured gain is 9.06~12.44 dBi for the first band and 11.76~14.84 dBi for the second band. The half power beam width is $57^{\circ}$ for x-z plane and $46^{\circ}$ for y-z plane at 1,100 MHz and $43^{\circ}$ and $28^{\circ}$ at 2,050 MHz, respectively.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.21 no.6
• /
• pp.25-32
• /
• 2021

In this study, it proposes a mode converter that is relatively easy to implement and can shorten the transmission line length of the final combining port and it was fabricated and tested by applying it to an 8-way spatial combiner. The proposed mode converter converts the signal converted from the doorknob-shaped circular disk connected to the ground into the TM₀₁ mode by opening it in the circular waveguide. The 8-way waveguide spatial combiner is designed and implemented so that 8 signals input from the H-plane are combined in a circular waveguide at the center, and the final combining mode is TM₀₁. The test results confirmed excellent performance with an insertion loss of less than 0.4dB and a combining efficiency of 95% or more. In addition, it was confirmed that it is suitable for high output by calculating the breakdown voltage and discharge threshold power of the new mode conversion structure through electric field analysis. The results confirmed through this study are expected to be applicable to high-power, high-efficiency SSPA in various fields in the future.