• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.6
• /
• pp.627-634
• /
• 2010

In this paper, a novel voltage-controlled oscillator(VCO) using the complimentary bifilar archimedean spiral resonator(CBASR) is presented for reducing the phase noise characteristic. A CBASR has compact dimension, a sharp skirt characteristic in stopband, a low insertion loss in passband, and a large coupling coefficient value, which makes a high Q value and improve the phase noise of VCO. The proposed VCO has the oscillation frequency of 2.396~2.502 GHz in the tuning voltage of 0~5 V, the output power of 7.5 dBm and phase noise of -119.16~-120.2 dBc/㎐ at the offset frequency of 100 kHz in tuning range.

• Journal of the Korean Vacuum Society
• /
• v.22 no.6
• /
• pp.335-340
• /
• 2013

This paper is for the simulation design to enhance the breakdown voltage of MHEMTs with an InP-etchstop layer. Gate-recess and channel structures has been simulated and analyzed for the breakdown of the MHEMT devices. The fully removed recess structure at the drain side of MHEMT shows that the breakdown voltage enhances from 2 V to almost 4 V as the saturation current at gate voltage of 0 V is reduced from 90 mA to 60 mA at drain voltage of 2 V. This is because the electron-captured negatively fixed charges at the drain-side interface between the InAlAs barrier and the $Si_3N_4$ passivation layers deplete the InGaAs channel layer more and thus decreases the electron current passing the channel layer and thus the impact ionization in the channel become smaller. In addition, the replaced InGaAs/InP composite channel with the same thickness in the same asymmetrically recessed structure increases the breakdown voltage to 5 V due to the smaller impact ionization and mobility of the InP layer at high drain voltage.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.1
• /
• pp.69-75
• /
• 2010

In this paper, with using the clapp type VCO(Voltage Controlled Osillator) configuration a wideband frequency synthesizer in UHF band is proposed. In order to design a wideband frequency synthesizer, the variation of phase in the negative resistance circuit as well as the load circuit was analyzed. Based on this result we propose a method to widen the operation range of the VCO. A frequency synthesizer using the proposed wideband VCO was designed and fabricated. It is shown that the synthesizer has the operating frequency range of 740~1,530 MHz by 0~5 V varactor tuning voltage, and it had the output power of 2~-6 dBm. Moreover, the phase noise measured as -77 dBc/Hz at 10 kHz offset, and as -108 dBc/Hz at 100 kHz offset from the oscillation frequency.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39A no.12
• /
• pp.691-698
• /
• 2014

An L-band single side band(SSB) mixer with CMOS switches and a C-band quadrature voltage-controlled oscillator(QVCO) have been developed using the TowerJazz 0.18-um RFCMOS process. The SSB mixer exhibits a conversion gain of 6.6 ~ 7.5 dB with a 70-dBc image rejection ratio and 65-dBc port isolation. The oscillation frequency range of the QVCO is 6.2 ~ 6.7 GHz with an output power of 4~6 dBm. For measurement, 1.8 V supply voltage is used while drawing 36 mA for the mixer and 23 mA for the QVCO.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.9
• /
• pp.967-973
• /
• 2009

In this paper, X-band satellite communication oscillator of double phase locked is implemented by constructing a couple of phased-locked loop, and then we have analyzed the phase noise of designed PLL-DRO. The designed phase-locked oscillator is consist of series feedback DRO, frequency divider, phase detector, loop filter and programmable PLL-IC. By dividing oscillation frequency of 12.6 GHz into two frequencies, it exhibits output power of 15.32 dBm at 6.3 GHz. Phase noises of implemented oscillator are -81 dBc/Hz@100Hz, -100.86 dBc/Hz@1 kHz, -111.12 dBc/Hz@10 kHz, -116 dBc/Hz@100 kHz and -140.49 dBc/Hz@1 MHz respectively. These indicate excellent stable operation of oscillator and very good phase noise characteristics.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.5
• /
• pp.682-690
• /
• 2015

The bonding performance of two types of wood adhesives, namely phenol-resorcinol-formaldehyde (PRF) resin and melamine-urea-formaldehyde (MUF) resin for glued laminated timber manufactured by high frequency (HF) heating was evaluated. The HF heating system consists of HF oscillator with dielectric heating system for curing adhesives, and hydraulic press system for clamping glued laminated timber. The designed frequency and output power of the HF system was as 5 MHz and 60 kW, respectively. To verify dielectric heating mechanism under HF oscillation, the heat loss factors of laminae and adhesives were measured. The results show that it is possible to selectively heat adhesives for their curing due to the remarkably higher loss factor of the adhesives than those of wood laminae. The temperature of adhesive in the bonding line reached up to the set temperature within a few seconds by high frequency oscillating, which advanced the curing of adhesive afterwards. The bonding performance, such as shear strength of bonding line, water soaking delamination, and boiling water soaking delamination of PRF resin met the requirement of Korean Standard (KS), however the MUF resin did not meet the KS requirement of boiling water soaking delamination. These results indicate that the HF heating system is successful to manufacture glued laminated timbers with PRF resins to meet the bonding requirements.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.9
• /
• pp.820-825
• /
• 2004

In this paper an octave tuning voltage controlled oscillator which is used in set-top TV tuner was designed. Oscillation frequency range is 0.9 GHz～2.2 GHz with 1.3 GHz bandwidth. By using 4 varactor diodes in base and emitter of transistor, wide-band tuning, sweep linearity and low phase noise could be achieved. Designed VCO requires a tuning voltage of 0 V ～ 20 V and DC consumption of 10 V and 15 mA. Designed VCO exhibits an output power of 5.3 dBm $\pm$1.1 dB and a phase noise below -94.8 dBc/Hz ＠ 10 kHz over the entire frequency range. The sweep linearity shows 65 MHz/V with a deviation of $\pm$10 MHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.5
• /
• pp.522-527
• /
• 2011

In this work, a 54 GHz divide-by-3 injection-locked frequency divider(ILFD) based on ring oscillator has been developed in a 0.13-${\mu}M$ Si RFCMOS technology for phase-locked loop(PLL) application. The free-running frequency is 18.92~19.31 GHz with tuning range of 0~1.8 V, consuming 70 mW with a 1.8 V supply voltage. At 0 dBm input power, the locking range is 1.02 GHz(54.82~55.84 GHz) and, with varactor tuning of 0~1.8 V, the total operating range is 2.4 GHz(54.82~57.17 GHz). The fabricated circuit size is 0.42 mm${\times}$0.6 mm including probing pads and 0.099 mm${\times}$0.056 mm for core area.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.5
• /
• pp.399-406
• /
• 2016

The large scale wind turbine blades usually experience periodic change of inflow speed due to blade rotation inside the ground shear flow region. Because of the vertical wind shear, the inflow velocity in the boundary layer region is maximum at uppermost position and minimum at lowermost position. These spatial distribution of wind speeds can lead to the periodic oscillation of the 6-component loads at hub and low speed shaft of the wind turbine rotor. In this study we compare the aerodynamic loads between two inflow conditions, i.e, uniform flow (no vertical wind shear effect) and normal wind profile. From the computed results all of the relative errors for oscillating amplitudes increased due to the ground shear flow effect. Especially bending moment and thrust at hub, and bending moments at LSS increased enormously. It turns out that the aerodynamic analysis including the ground shear flow effect must be considered for fatigue analysis.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.2A
• /
• pp.202-208
• /
• 2010

The performance of upstream transmission in SCM-PON is generally limited by the presence of OBI which is caused by the beating of two or more lasers. In this paper, we propose a novel approach for reducing OBI problem by using heterodyne detection with an additional LD as a local oscillator, resulting that the RF signal is shifted to the other spectal band. In addition, it is possible that the proposed method can provide the cost-effective solution thanks to the loop-back mechanism using R-SOA in ONUs. The performance is superior when the spectral width of LD is smaller and the power difference between the transmission LD and the oscillation LD is bigger. System configuration and design consideration are discussed. Performance of the systems is evaluated by simulator called OptSim. It is expected to provide WDM/SCM-PON system not only cost-effective but also efficient in increasing the number of subscribers.