• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2000.11a
• /
• pp.150-153
• /
• 2000

In this paper, we have designed a 2 stage MMIC power amplifier which has flat gains of in-band and reasonable out-band cutoff characteristics using 0.5$\mu\textrm{m}$ MESFET libra교 of ETRI. For the 1st stave, we obtaind P$_{1dB}$ of 9.2 dBm and gain 10.8 dB using 6 finger D-MESFET and P$_{1dB}$ of 18.4 dBm and gain of 10.8 dB using 14 finger D-MESFET for the 2nd stage, which is power matched using LIBRA's embedded TUNER. Also in-band gain flatness and out-band cutoff characteristics are obtained by attaching LC tank in the output matching circuit. The designed 2 stage MMIC power amplifier has bandwidth of 0.95～2.8 GHz, gain of 20 dB and P$_{1dB}$of 17.2 dBm. Especially gain flatness of $\pm$0.8dB was obtained in 1.8～2.5 GHz frequency ranges. And chip size is 1.4$\times$1.4 mm..4 mm.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.16 no.6
• /
• pp.60-65
• /
• 2002

The purpose of this study is to measure and compare the output power characteristics and optical gain for selenium vapour laser depending on the He gas purity. The purity of the He gas was improved with a special He-filter. During the measurement the individual wavelengths were selected with a birefringent filter. The result shows that compared with those of laser without He-filter, the output-coupling power and small signal gain of laser with He-filter increase in the most of the lines. Especially, the output-coupling power and small signal gain for the strong lines (497.6 nm, 499.3 nm, 506.9 nm, 517.6 nm, 522.8 nm, 530.5 nm), blue(460.4 nm, 464.8 nm) and red(644.4 nm 649.1 nm) lines lies notably higher.

• Current Optics and Photonics
• /
• v.4 no.6
• /
• pp.472-476
• /
• 2020

We have investigated the impact of optical filter bandwidth on the performance of all-optical automatic gain-controlled (AGC) erbium-doped fiber amplifiers (EDFAs). In principle, an optical bandpass filter (OBPF) should be placed within the feedback gain-clamping loop to set the lasing wavelength as well as the passband of the feedback amplified spontaneous emission (ASE) in all-optical AGC EDFA. From our measurement results, we found that the power level of feedback ASE with 0.1 nm passband of the optical filter was smaller than the ones with >0.2 nm passband cases. Therefore, the peak-to-peak power variation of the surviving channel with 0.1 nm passband was much larger than the ones with >0.2 nm passband. In addition, no significant difference in the power level of the feedback ASE was observed when the passband of the optical filter was ranging from 0.2 nm to 4.5 nm in our measurements. From these results, we have concluded that the passband of the optical filter should be slightly larger than 0.2 nm by taking into account the effect of feedback ASE power and the efficient use of the EDFA gain spectrum for the lasing ASE peak.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.1
• /
• pp.52-56
• /
• 2014

In this paper, a high-efficiency power amplifier is implemented using a gate and drain bias control circuit for WPT (Wireless Power Transmission). This control circuit has been employed to improve the PAE (Power Added Efficiency). The gate and drain bias control circuits consists of a directional coupler, power detector, and operation amplifier. A high gain two-stage amplifier using a drive amplifier is used for the low input stage of the power amplifier. The proposed power amplifier that uses a gate and drain bias control circuit can have high efficiency at a low and high power level. The PAE has been improved up to 80.5%.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.8
• /
• pp.1572-1579
• /
• 2009

In this dissertation ultra-broadband power amplifier(UPA) was designed and fabricated using negative feedback technique. UPA was made of pre-amplifier, drive amplifier and power amplifier. Negative feedback technique was used to achieve ultra-broadband performance. Designed power amplifier has 30dB gain and 2W output power. The load-pull data of power amplifier for optimal power matching was extracted from the measured S-parameter. Fabricated PCB material, permittivity is 4.6 and thickness is 0.8mm, is FR4 and UPA was fabricated 3 modules for comparison of the simulated and measured results. Size of the fabricated pre-amplifier and drive amplifier module is 40mm'50mm'16mm. And from the experimental results, gain of the pre-amplifier module is 9.87dB at 2GHz and flatness is 0.63dB. Experimental result of the drive amplifier module is 10.97dB at 2GHz and flatness of that is 0.26dB. Test result of the power amplifier module is 10.71dB at 2GHz and flatness is 0.72dB. Total size of the power amplifier is 45mm'134mm'16mm. According to the test results, gain of the UPA is 28.98dB at 2GHz and flatness is 1.68dB. Output power was 32.098dBm at 2GHz, 32.154dBm at 1GHz and 31.273dBm at 100MHz.

• Transactions of The Korea Fluid Power Systems Society
• /
• v.4 no.1
• /
• pp.13-17
• /
• 2007

The brake gain adaptive wheel slip controller for a vehicle is designed in this paper. The brake gain from braking pressure to braking torque defined by friction coefficient, friction area and effective friction radius is estimated by the adaptive law based on the wheel slip dynamics. And the wheel slip controller is designed based on the estimated brake gain. The robustness of the designed controller is analyzed using Lyapunov function and the convergence of brake gain is verified. Proposed wheel slip controller is verified via CarSim simulation with two kinds of desired wheel slip ratio.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.11 no.4
• /
• pp.336-343
• /
• 2011

This paper introduces a simple variable gain amplifier (VGA) structure that shows an inherently dB-linear gain control property. Requiring no additional components for dB-linear control, the structure is compact and power efficient. The designed two-stage VGA shows a gain control range of 60dB with the gain error in the range of ${\pm}0.4$ dB. The power consumption including the output buffer is 20.4 mW from 1.2 V supply voltage with bandwidth of 630 MHz. The prototype was fabricated in a 0.13 ${\mu}m$ CMOS process and the VGA core occupies 0.06 $mm^2$.

• Journal of Power Electronics
• /
• v.10 no.6
• /
• pp.680-685
• /
• 2010

Although LLC resonant converters have the advantages of a wide operation range and high efficiency, the lack of an analytical solution for the peak gain makes it difficult to optimize the resonant tank design, when considering not only the normal condition but also the holdup time requirement. In this paper, based on a mathematical analysis of a LLC resonant converter at the peak gain point, an analytical solution for the peak gain has been developed. By using the developed analytical solution, the peak gain with given resonant tank parameters can be obtained. To confirm the validity of the developed analytical solution, simulations and experimental results are compared.

• Journal of Institute of Control, Robotics and Systems
• /
• v.9 no.12
• /
• pp.1065-1070
• /
• 2003

We present a power control with variable state feedback gain (VFPC) to improve outage convergence rate of distributed constrained power control. The variable state feedback gain includes the information of the desired SIR changes and must be a decreasing sequence for the convergence. The proof of the convergence is given. The proposed algorithm can improve the outage convergence rate and SIR (Signal to Interference Ratio) response at transient as well as at steady state. The simulation results are given to demonstrate the feasibility of the proposed scheme.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.30A no.5
• /
• pp.45-51
• /
• 1993

An erbium doped fiber amplifier(EDFA) pumped by aingle 1.48$\mu$m LD was fabricated, and its gain and noise characteristics were measured. As a signal source, 1548 nm wavelength DFB LD was used. The small signal net gain of the EDFA module was 21.8 dB with maximum gain coefficient 0.7dB/mW for the erbium fiber length of 17.6 m, the pump power of 58 mW, and an input signal power of -25 dBm, respectively. The saturation power of the EDFA was 1 dBm for the input signal power of -5 dBm and the noise figure, measured by using an optical spectrum analyzer, was 5.8 dB for the input signal power of -40 dBm.