• The Transactions of the Korean Institute of Power Electronics
• /
• v.17 no.2
• /
• pp.107-113
• /
• 2012

This paper proposes a PDS(Power Transfer Display separation) method for AC-PDP. The proposed PDS method can transfer power and perform an energy recovery by a power conversion circuit operates differently depending on the time. As a result, it uses less of components than conventional PDP power supply and sustain circuit use. Moreover, the manufacturing process can be streamlined. Therefore, the proposed method is suitable for low cost PDP module. To confirm the operation, validity and features of the proposed PDS method, experimental results from a prototype for 42-in diagonal PDP are presented.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.5 no.3
• /
• pp.210-219
• /
• 2005

We report on a low-cost V-band wireless transceiver with no use of any local oscillator in the receiver block using a self-heterodyne architecture. V-band millimeter-wave monolithic IC (MMIC) modules were developed to demonstrate the wireless transceiver using coplanar waveguide (CPW) and GaAs PHEMT technologies. The MMIC modules such as the MMIC low noise amplifier (LNA), medium power amplifier (MPA) and the up/down-mixer were installed in the transceiver system. To interface the MMIC chips with the component modules for the transceiver system, CPW-to-waveguide fin-line transition modules of WR-15 type were designed and fabricated. The fabricated LNA modules showed a $S_{21}$ gain of 8.4 dB and a noise figure of 5.6 dB at 58 GHz. The MPA modules exhibited a gain of 6.9 dB and a $P_{1dB}$ of 5.4 dBm at 58 GHz. The conversion losses of the up-mixer and the down-mixer module were 14.3 dB at a LO power of 15 dBm, and 19.7 dB at a LO power of 0 dBm, respectively. From the measurement of V-band wireless transceiver, a conversion gain of 0.2 dB and a $P_{1dB}$ of 5.2 dBm were obtained in the transmitter block. The receiver block showed a conversion gain of 2.1 dB and a $P_{1dB}$ of -18.6 dBm. The wireless transceiver system demonstrated a successful data transfer within a distance of 5 meters.

• Journal of Advanced Navigation Technology
• /
• v.21 no.4
• /
• pp.413-421
• /
• 2017

In this paper, we designed and fabricated a compact UHF receive module for efficient operation such as tactical and operation situation, target location information confirmation, target reset using Link-K(Korean joint tactical data link system). And the effect of target reset was analyzed by simulation. The designed module consists of UHF(ultra high frequency) receiver section, control section, and power distribution section. The UHF receiver section performs frequency down conversion, filtering and automatic gain control, etc. The control section demodulates frequency down-converted signals, extracts information, and performs external interworking. The power distribution section supplies external power, generates and supplies the power required by each section. The fabricated module was dimension of $105{\times}105{\times}80mm$ and weighed 1.10 kg and The receiving distance is more than 50 km.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.2
• /
• pp.99-108
• /
• 2018

This paper presents a design study of a solid state power oscillator to replace the conventional magnetron. The operational conditions of a single-stage 300 W LDMOS power amplifier were fully characterized. The power module consisted of two amplifiers connected in parallel. A delay-line feedback loop was designed for self-oscillation. A phase shifter was inserted in the delay-line feedback loop for adjusting the round-trip phase. Experiments performed using the power oscillator showed an output power of 800 W and a DC-RF conversion efficiency of 58 % at 2.327 GHz. The measured results were in good agreement with those predicted by numerical simulations.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.24 no.3
• /
• pp.201-206
• /
• 2019

This study presents the design and experimental result of a GaN-based DC-DC converter with an integrated gate driver. The GaN device is attractive to power electronic applications due to its superior device performance. However, the switching loss of a GaN-based power converter is susceptible to the common source inductance, and converter efficiency is severely degraded with a large loop inductance. The objective of this study is to achieve high-efficiency power conversion and the highest power density using a multiphase integrated half-bridge GaN solution with minimized loop inductance. Before designing the converter, several GaN and Si devices were compared and loss analysis was conducted. Moreover, the impact of common source inductance from layout parasitic inductance was carefully investigated. Experimental test was conducted in buck mode operation at 48 -12 V, and results showed a peak efficiency of 97.8%.

• Proceedings of the KIPE Conference
• /
• 2006.06a
• /
• pp.488-491
• /
• 2006

In this paper proposed method of maximum power point tracking using boost converter for a connected single phase inverter with photovoltaic system. The maximum power point tracking control is based on generated circuit control MOSFET switch of boost converter and single phase inverter uses predicted current control to control four IGBT's switch in full bridge. The predicted current control provide current with sinusoidal wave shape and inphase with voltage. The generation control circuit allows each photovoltaic module to operate independently at peak capacity, simply by detecting of the output power of the system. Furthermore, the generation control circuit attenuates low-frequency ripple voltage, which is caused by the full-bridge inverter, across the photovoltaic modules. Consequently, the output power of system is increased due to the increase in average power generated by the photovoltaic modules. The effectiveness of the proposed inverter system is confirmed experimentally and by means of simulation.

• Proceedings of the KIPE Conference
• /
• 2004.07a
• /
• pp.82-86
• /
• 2004

In this paper, a cycler system for the Lithium-Polymer battery with the large capacity of 120Ah is presented. This system is constituted as the two units for the charging and discharging. The Lithium-Polymer battery should be charged in CC and CV mode, and it is required a very high precision control of the voltage and current for the charging unit. To decrease the switching noises and harmonics, parallel operation method is adopted and utilized in the power conversion module. The discharging unit has a link AC system function to return the discharging energy of battery to AC line and has comparatively less thermal loss. These units are designed to be controlled and monitored by personal computer. The total system for the battery charging and discharging is described and presented.

• Proceedings of the KIPE Conference
• /
• 2012.11a
• /
• pp.201-202
• /
• 2012

This paper presents design and implementation of the PCU(150 kVA 3-Phase PWM Inverter for Electric Vehicles). For Implementation of the PCU, it is consist with Case, Connectors, IGBT module for PWM switching, DC-capacitor for dc-source, resolver for sensing of speed & position, and PCB board for control & gate-driver. Also, for the purpose of stable operation of the PCU in vehicle with variable torque condition in motor, current control scheme based on torque-map are developed. According to real-car test mode, the prototype of proposed the PCU is verified with performance and stability. Thus, design and implement of the PCU are discussed, and experimental results are presented in this paper.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1788-1790
• /
• 2005

In this paper, an operating characteristics of a 50 kW gird-connected photovoltaic(PV) power system was analysed from 2000 to 2004. The construction of the PV system includes a 3-phase inverter for grid connection, PV module, distribution box, and data monitoring system. The major results of the demonstration test of the 50 kW class gird-connected PV system showed that efficiency of PV system was 11.13%, and the conversion efficiency of the inverter was 92% at a 50% load.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.6 s.97
• /
• pp.603-614
• /
• 2005

In this paper, digital ultra-narrowband Walky-Talky using direct conversion method for CQPSK modulation scheme is implemented with satisfying the requirements of APCO P25. RF transceiver design and implementation scheme that minimize the influence of DC-offset and AC-coupling at ultra-narrowband is proposed. This scheme also minimizes the influence of nonlinear characteristic at power amplifier fir CQPSK modulation method. Test results of full system including DSP module and direct conversion RF transceiver show that FCC emission mask at 36.8 dBm PEP meets the standard requirements. The characteristic of receiver AGC by PWM control signal is linear at 40 dB dynamic range and voice communication at input power level of -116 dBm is successful. Also it is verified that the performance of BER versus frequency offset and versus SNR meets the standard requirements.