• 조명전기설비학회논문지
• /
• 제16권6호
• /
• pp.137-144
• /
• 2002

배선용 차단기(MCCB)는 신속한 고장전류 차단과 전원시스템의 안정성을 확보하기 위해 배전시스템에 폭넓게 사용되고 있다. 본 논문에서는 MCCB의 소호부 형상에 따른 차단성능을 파악하고 이를 통해 성능향상을 꾀하고자 3차원 자계해석을 이용한 차단성능 평가해석기법을 개발하고, 개발한 평가해석기법을 각 모델 차단기에 적용한 바를 기술하였다. 또한, 소호부내 3분할 다단형 아크런너을 구성하여 불연속 통전경로를 형성함으로 해서 차단성능에 미치는 영향을 살펴보았다. 끝으로, 이상의 연구내용을 토대로 새로운 소호부 형상을 고안하여 국내 최초로 460［V］/225［A］/50［kA］ 대전력 단락시험에 성공한 결과를 제시하였다.

• 마이크로전자및패키징학회지
• /
• 제27권4호
• /
• pp.55-60
• /
• 2020

태양광 발전소에 설치된PERC 태양광 모듈 스트링-어레이는 고전압의 전위차로 인해 여전히 potential-induced degradation(PID) 열화 현상이 여전히 보고되고 있다. 이는 태양전지 모듈 커버글라스의 Na+ 이온이 태양전지 봉지재(EVA)를 투과하여 셀 표면으로 전이되고 결함이 많이 분포되어 있는 ARC(SiOx/SiNx) 계면에 양전하가 축적됨으로써 shunt-Resistance(Rsh)가 감소되고 누설전류량이 증가되어 태양전지 출력이 저하되는 현상이다. 본 연구에서는 이를 방지하기 위해 나노임프린트 리소그래피(nano-imprint lithography, NIL) 방식을 이용하여 모스아이(Moth-eye) 나노 구조를 광학 필름 후면에 증착 하였고, 이를 커버글라스와 EVA 사이에 삽입하여 태양광 미니 모듈을 구성하였다. PID 열화 현상을 확인하기 위해 IEC 62804-1 규격에 기반한 셀 단위 PID 열화가속시험을 진행하였고, Light I-V, Dark I-V 분석을 통해 출력(Pmax), 효율(Efficiency), 병렬 저항(shunt resistance)을 확인하였다. 그 결과 기존의 태양전지는 초기 효율 19.76%에서 6.3% 감소하였으나 모스아이 나노 구조 광학 필름(Moth-eye film)이 적용된 태양전지는 0.6% 만 감소하여 PID 열화 현상이 방지되는 것을 확인하였고, 모스아이 나노구조를 통해 투과도가 4% 향상되어 미니 모듈 출력이 2.5% 향상되었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2016년도 제50회 동계 정기학술대회 초록집
• /
• pp.200.2-200.2
• /
• 2016

Carbon-based materials have been known as ablative material and have been used for thermal protection systems. Ablation is an erosive phenomenon that results in thermochemical and thermomechanical changes on materials. Ablation resistance is one of the key properties that determines performance and life-time of the thermal protection material under ablative conditions. In this study, ablation properties of graphite, 3-dimensional (C/C) composites (needle-punched type and rod type) were investigated byusing a plasma wind tunnel which produce a supersonic plasma flow from a segmented arc heater with the power level of 0.4 MW. The mass losses and surface roughness changes which contain main result of the ablation are measured. A morphological analysis ofthe carbon-based materials, before and after the ablation test, are performed through field emission scanning electron microscopy (FE-SEM) and non-contact 3D surface measuring system. Electronic balance and a portable surface roughness tester were used for evaluation of the recession and mass loss of the test samples.

• 자원리싸이클링
• /
• 제14권1호
• /
• pp.39-46
• /
• 2005

본 연구에서는 고상폐기물(소각재) 처리를 위해 중간 전극 (IEI, Inter-Electrode Insert)이 있는 button 형태의 고형 체형 고출력 토치를 개발하였고 폐기물처리 플라즈마설비에 적용하여 운전특성을 얻었다. 본 연구의 토치 실험 결과 비이송형 모드에서는 가스량의 증가에 따라 전압이 증가하였고, 이송형 모드에서는 가스량 변화에는 영향이 없었으나 토치와 바닥면과의 거리, 슬래그의 성분 그리고 용융 슬래그의 체적에 따라 전압의 변화가 발생하였다. 특히 아크전압이 슬래그내의 total Fe 함량이 10% 내외에서 안정적으로 유지되었으며, 전기전도도 계산결과 0.05~0.25${\Omega}^{-1}cm^{-1}$ 범위로 나타났다. 본 연구의 토치 효율은 75~85%로 나타났으며, 마모율은 2${\times}10^{-6}~6{\times}10^{-6}$ kg/s의 범위로 나타났다.

• Restorative Dentistry and Endodontics
• /
• 제27권5호
• /
• pp.488-492
• /
• 2002

The purpose of this study was to evaluate the effectiveness of plasma arc curing (PAC) unit for composite and compomer curing. To compare its effectiveness with conventional quartz tungsten halogen (QTH) light curing unit, the polymerization shrinkage rates and amounts of three composites (Z100, Z250, Synergy Duo Shade) and one compomer, that had been light cured by PAC unit or QTH unit, was compared using a custome made linometer. The measurement of polymerization shrinkage was peformed after polymerization with either QTH unit or PAC unit. In case of curing with the PAC unit, the composite was light cured with Apollo 95E for 6s, the power density of which was recorded as 1350 mW/$\textrm{cm}^2$ by Coltolux Light Meter. For light curing with QTH unit, the composite was light cured for 30s with the XL2500, the power density of which was recorded as 800 mW/$\textrm{cm}^2$ by Coltolux Light Meter. The amount of linear polymerization shrinkage was recorded in the computer every 0.5s for 60s. Ten measurements were made for each material. The amount of linear polymerization shrinkage for each material in 10s and 60s which were cured with PAC or QTH unit were compared with t test. The amount of polymerization shrinkage in the tested materials were compared with 1way ANOVA with Duncan's multiple range test. As for the amounts of polymerization shrinkage in 60s, there was no difference between PAC unit and QTH unit in Z250 and Synergy Duo Shade. In Z100 and Dyract AP, it was lower when it was cured with PAC unit than when it was cured with QTH unit (p<0.05). As for the amounts of polymerization shrinkage in 10s, there was no difference between PAC unit and QTH unit in Z100 and Dyract AP. The amounts of polymerization shrinkage was significantly higher when it was cured with PAC unit in Z250 and Synergy Duo Shade (p<0.05). The amounts of polymerization shrinkage in the tested materials when they were cured with QTH unit were Z250 (6.6um) < Z100 (9.3um), Dyract AP (9.7um) < Synergy Duo Shade (11.2um) (p<0.05). The amount of polymerization shrinkage when the materials were cured with PAC unit were Dyract AP (5.6um) < Z100 (8.1um), Z250(7.0um) < Synergy Duo Shade (11.2um) (p<0.05).

• 대한기계학회논문집A
• /
• 제26권5호
• /
• pp.924-931
• /
• 2002

Vacuum interrupters in order to be used in various switch-gear components such as circuit breakers, distribution switches, contactors, etc. spread the arc uniformly over the surface of the contacts. The electrodes of vacuum interrupters are made of sinter-forged Cu-Cr materials for good electrical and mechanical characteristics. Since the closing velocity is 1-2m/s and impact deformation of the electrode depends on the strain rate at that velocity, the dynamic behavior of the sinter-forged Cu-Cr is a key to investigate the impact characteristics of the electrodes. The dynamic response of the material at the high strain rate is obtained from the split Hopkinson pressure bar test using disc-type specimens. Experimental results from both quasi-static and dynamic compressive tests are Interpolated to construct the Johnson-Cook model as the constitutive relation that should be applied to simulation of the dynamic behavior of the electrodes. The impact characteristics of a vacuum interrupter are investigated with computer simulations by changing the value of five parameters such as the initial velocity of a movable electrode, the added mass of a movable electrode, the wipe spring constant, initial offset of a wipe spring and the virtual fixed spring constant.

• 대한기계학회논문집
• /
• 제10권6호
• /
• pp.916-922
• /
• 1986

본 논문에서는 여러 연구자들이 반타원형 표면균열에 대한 응력확대계수의 수 정계수(correction factor)을 이론해석, 수치해석 및 실험해석 등을 통하여 구했는데, 그 결과는 서로가 5∼100%의 차이를 나타내고 있는 것이다. 이 때문에 표면균열에 대한 연구보고는 다른 분야에 비하여 비교적 적은 편이며, 현재까지 펴면균열의 피로 성장거동에 대한 정열이 설정되어 있지 못한 실정인 것이다. 이에 저자들은 표면균 열의 피로성장거동에 대한 다각적인 연구계획을 추진하고 있는 중이며, 본 보고서는 그 제1단계 연구로서, 초기 표면균열의 크기가 피로균열성장거동에 미치는 영향을 규 명하기 위한 실험적인 연구결과이다.

• 전기학회논문지
• /
• 제62권5호
• /
• pp.643-648
• /
• 2013

In this study, degradation was observed by irradiating UV rays to the polymer insulators which have been widely used in outdoor electric power facilities. For an indoor accelerated UV test, 0.55 w/m2 of UV rays were applied using a xenon-arc method. A UV detection system with 65 ${\phi}mm$ in diameter, 100 mm in length and 1.0 of brightness (F/#) has been designed. Even though efflorescence on the surface of polymer insulators wasn't observed according to the accelerated UV test. UV rays were detected at around 50% and 40% of insulation breakdown in EPDM and silicone-type insulators respectively. As degradation continued because of an indoor accelerated UV test, breakdown voltage with which UV rays can be detected in an early stage decreased as well. A silicone polymer insulator would be severer than EPDM polymer insulator in terms of surface degradation because of UV strength against $V_m/V_{BD}$ was high in silicone polymer insulators. UV strength in silicone-type insulators increased at 1,000 $kJ/m^2$ because contact angle at the intial stage sharply decreased to from $113^{\circ}$ to $92.1^{\circ}$.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.1774-1777
• /
• 1996

In this paper, applicability of SI-PD(switching impulse - partial discharge) testing method was put on an attempt as a newly proposed diagnostic method for the underground distribution power cable system in Korea. For this purpose, SI-PD testing equipment was designed, and tests were performed using artificial needle-type defects integrated into the 22.9 kV CN/CV cables in drder to prove its reliability. As a result, arc noises, generated from spark gap, were considerably decreased by use of a pneumatic switch immersed into oil, and artificial needle-type defects were well detected with impulse voltage level under $2U_0$. These results imply that it is likely possible to apply SI-PD measurement method as a the nondistructive test for the 22.9 kV CN/CV cable system in Korea.

• 한국항공우주학회지
• /
• 제32권9호
• /
• pp.114-121
• /
• 2004

정지궤도 통신위성 원격측정명령처리기의 기술인증모델 개발을 위하여 기술모델의 열 설계변경 및 해석을 수행하였다. 보드레벨의 소모전력량 측정치와 열주기시험의 결과를 활용하여 기술모텔에 대한 열해석모델을 개발하였다. 발열소자의 열소산 모델링은 인쇄회로기판에 투영된 소자의 footprint를 생성하고 그 표면의 전 영역에 균일하게 열소산량을 가하였다. 열설계변경(안)에 따라 설계변경 후 기술인증수준의 열진공환경에서 소자온도를 예측한 결과, CTU의 모든 소자들의 접합온도는 허용온도 이내로 존재하였다.